Endress+Hauser CCS50D Bedienungsanleitung
Products Solutions Services
Operating Instructions
CCS50D
Digital sensor with Memosens technology for
determining chlorine dioxide
BA01773C/07/EN/02.19
71431040
2019-02-08
CCS50D Table of contents
Endress+Hauser 3
Table of contents
1 About this document ........... 4
1.1 Warnings ........................... 4
1.2 Symbols used ........................ 4
2 Basic safety instructions ....... 6
2.1 Requirements for the personnel ........ 6
2.2 Designated use ...................... 6
2.3 Workplace safety .................... 6
2.4 Operational safety ................... 7
2.5 Product safety ....................... 7
3 Product description ............. 8
3.1 Product design ....................... 8
4 Incoming acceptance and
product identification ......... 13
4.1 Incoming acceptance ................ 13
4.2 Product identification ................ 13
5 Installation .................... 15
5.1 Installation conditions ............... 15
5.2 Mounting the sensor ................ 17
5.3 Post-installation check ............... 24
6 Electrical connection .......... 25
6.1 Connecting the sensor ............... 25
6.2 Ensuring the degree of protection ..... 25
6.3 Post-connection check ............... 26
7 Commissioning ................ 27
7.1 Function check ..................... 27
7.2 Sensor polarization .................. 27
7.3 Sensor calibration ................... 27
8 Diagnostics and
troubleshooting ............... 29
9 Maintenance .................. 31
9.1 Maintenance schedule ............... 31
9.2 Maintenance tasks .................. 32
10 Repair .......................... 39
10.1 Spare parts ........................ 39
10.2 Return ............................ 39
10.3 Disposal ........................... 39
11 Accessories .................... 40
11.1 Maintenance kit CCV05 .............. 40
11.2 Device-specific accessories ............ 40
12 Technical data ................. 41
12.1 Input .............................. 41
12.2 Performance characteristics .......... 43
12.3 Environment ....................... 44
12.4 Process ............................ 44
12.5 Mechanical construction ............. 45
13 Installation and operation in
hazardous environment Class
I Div. 2 .......................... 46
Index ................................. 48
About this document CCS50D
4 Endress+Hauser
1 About this document
1.1 Warnings
Structure of information Meaning
LDANGER
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious injury.
LWARNING
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious injury.
LCAUTION
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.
NOTICE
Cause/situation
If necessary, Consequences of non-
compliance (if applicable)
‣Action/note
This symbol alerts you to situations which may result in damage to property.
1.2 Symbols used
Symbol Meaning
Additional information, tips
Permitted or recommended
Not permitted or not recommended
Reference to device documentation
Reference to page
Reference to graphic
Result of a step
CCS50D About this document
Endress+Hauser 5
1.2.1 Symbols on the device
Symbol Meaning
Reference to device documentation
Basic safety instructions CCS50D
6 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
Installation, commissioning, operation and maintenance of the measuring system may be
carried out only by specially trained technical personnel.
‣The technical personnel must be authorized by the plant operator to carry out the specified
activities.
‣The electrical connection may be performed only by an electrical technician.
‣The technical personnel must have read and understood these Operating Instructions and
must follow the instructions contained therein.
‣Measuring point faults may be repaired only by authorized and specially trained personnel.
Repairs not described in the Operating Instructions provided must be carried out only
directly at the manufacturer's site or by the service organization.
2.2 Designated use
Drinking water and industrial water must be disinfected through the addition of appropriate
disinfectants such as chlorine gas or inorganic chlorine compounds. The dosing quantity must
be adapted to continuously fluctuating operating conditions. If the concentrations in the water
are too low, this could jeopardize the effectiveness of the disinfection. On the other hand,
concentrations which are too high can lead to signs of corrosion and have an adverse effect on
taste, as well as generating unnecessary costs.
The sensor was specifically developed for this application and is designed for continuous
measurement of chlorine dioxide in water. In conjunction with measuring and control
equipment, it allows optimal control of disinfection.
Use of the device for any purpose other than that described, poses a threat to the safety of
people and of the entire measuring system and is therefore not permitted.
The manufacturer is not liable for damage caused by improper or non-designated use.
2.2.1 Hazardous environment in accordance with cCSAus NI Cl. I, Div. 2 1)
1. The device must be installed in a housing or cabinet that can be accessed only by means
of a tool or key.
2. Pay attention to the control drawing and the specified application conditions in the
appendix of these Operating Instructions, and follow the instructions.
2.3 Workplace safety
As the user, you are responsible for complying with the following safety conditions:
• Installation guidelines
• Local standards and regulations
1) Only if connected to CM44x(R)-CD*
CCS50D Basic safety instructions
Endress+Hauser 7
Electromagnetic compatibility
• The product has been tested for electromagnetic compatibility in accordance with the
applicable European standards for industrial applications.
• The electromagnetic compatibility indicated applies only to a product that has been
connected in accordance with these Operating Instructions.
2.4 Operational safety
Before commissioning the entire measuring point:
1. Verify that all connections are correct.
2. Ensure that electrical cables and hose connections are undamaged.
3. Do not operate damaged products, and protect them against unintentional operation.
4. Label damaged products as defective.
During operation:
‣If faults cannot be rectified:
products must be taken out of service and protected against unintentional operation.
2.4.1 Special instructions
‣Do not operate the sensors under process conditions where it is expected that osmotic
conditions will cause electrolyte components to pass through the membrane and into the
process.
Use of the sensor for its intended purpose in liquids with a conductivity of at least 10 nS/cm
can be classified as safe in terms of the application.
2.5 Product safety
The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
European standards have been observed.
Product description CCS50D
8 Endress+Hauser
3 Product description
3.1 Product design
The sensor consists of the following functional units:
• Membrane cap (measuring chamber with membrane)
– Separates the inner amperometric system from the medium
– With robust PVDF membrane and pressure relief valve
– Guarantees a defined and consistent electrolyte film between cathode and membrane
– With special support grid between cathode and membrane for a defined and consistent
electrolyte film and therefore a relatively constant reading at varying pressures and flows
• Sensor shaft with
– Large anode
– Cathode embedded in plastic
– Embedded temperature sensor
3
1
2
4
5
7
6
8
A0034227
1 Sensor structure
1 Memosens plug-in head
2 Sensor shaft
3 Large anode, silver/silver chloride
4 Gold cathode
5 Grooves for installation adapter
6 Membrane cap with dirt-repellent
membrane
7 Pressure relief valve (elastic)
8 Sensor membrane
3.1.1 Measuring principle
Chlorine dioxide levels are determined in accordance with the amperometric measuring
principle.
The chlorine dioxide (ClO2) in the medium diffuses through the sensor membrane and is
reduced to chloride ions (Cl-) at the gold cathode. At the silver anode, silver is oxidized to
CCS50D Product description
Endress+Hauser 9
silver chloride. Electron donation at the gold cathode and electron acceptance at the silver
anode cause a current to flow which is proportional to the concentration of chlorine dioxide in
the medium. This process does not depend on the pH value over a wide range.
The transmitter uses the current signal to calculate the measured variable for concentration in
mg/l (ppm).
3.1.2 Effects on the measured signal
pH value
pH dependency
pH value Result
< 3.5 Chlorine is produced if chloride (Cl-) is present in the medium at the same time. The strong cross-sensitivity
to chlorine dioxide causes an increase in the measured value.
3.5 to 9 The pH value does not affect measurement of the chlorine dioxide concentration in the medium.
> 9 Chlorine dioxide is unstable and decomposes.
Flow
The minimum flow velocity of the membrane-covered measuring cell is 15 cm/s (0.5 ft/s).
• When using the Flowfit CCA151 flow assembly, this corresponds to a flow rate of
5 l/h (1.3 gal/h).
• When using the CCA250 flow assembly, this corresponds to a flow rate of
30 l/h (7.9 gal/h) (upper edge of float at the height of the red bar mark).
Product description CCS50D
10 Endress+Hauser
80
90
100
relative slope / maximum slope in %
CCA151 flow gal/hr
CCA250 flow gal/hr
flow velocity at the membrane "/s
0 0.5 1 1.5 2 3
0 5 10 25 40
012 3 4 5 6
2.5
15 20 30 35
A0034487-EN
2 Correlation between slope of electrode and flow velocity at the membrane/flow rate in assembly
At higher flow rates, the measured signal is virtually flow-independent. However, if the flow
rate falls below the specified value, the measured signal depends on the flow.
The installation of an INS proximity switch in the assembly enables reliable detection of this
invalid operating status, thus triggering an alarm or causing the dosing process to be switched
off if necessary.
Below the minimum flow rate, the sensor current is more sensitive to flow fluctuations. For
abrasive media, it is recommended not to exceed the minimum flow. If suspended solids are
present, which may form deposits, the maximum flow rate is recommended.
Temperature
Changes in the temperature of the medium affect the measured value:
• Increases in temperature result in a higher measured value (approx. 4 % per K)
• Decreases in temperature result in a lower measured value.
Use of the sensor in combination with the Liquiline enables automatic temperature
compensation (ATC). Recalibration in the case of temperature changes is not necessary.
1. If automatic temperature compensation is disabled at the transmitter, the temperature
must be maintained at a constant level following calibration.
2. Otherwise, recalibrate the sensor.
Inhaltsverzeichnis
Andere Endress+Hauser Zubehör Handbücher
Endress+Hauser
Endress+Hauser Liquiphant M FTL51C Bedienungsanleitung
Endress+Hauser
Endress+Hauser ISEmax CAS40D Bedienungsanleitung
Endress+Hauser
Endress+Hauser Deltapilot S DB50 Handbuch
Endress+Hauser
Endress+Hauser Ceramax CPS341D Bedienungsanleitung
Endress+Hauser
Endress+Hauser Turbimax CUS51D Bedienungsanleitung
Endress+Hauser
Endress+Hauser Oxymax COS22D Bedienungsanleitung
Endress+Hauser
Endress+Hauser OUSAF46 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Deltabar FMD71 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Turbimax CUS50D Bedienungsanleitung
Endress+Hauser
Endress+Hauser Turbimax CUS71D Bedienungsanleitung
Endress+Hauser
Endress+Hauser Proline 200 FOUNDATION Fieldbus Technische Daten
Endress+Hauser
Endress+Hauser Liquipoint T Series Handbuch
Endress+Hauser
Endress+Hauser Proline Promag Bedienungsanleitung
Endress+Hauser
Endress+Hauser NAR 300 Technische Daten
Endress+Hauser
Endress+Hauser Oxymax H COS21D Bedienungsanleitung
Endress+Hauser
Endress+Hauser CCS120 Bedienungsanleitung
Endress+Hauser
Endress+Hauser OUSAF44 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Proline Promag 50 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Soliwave FQR56 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Deltapilot M FMB50 Handbuch
