Endress+Hauser Analytik Jena Biometra TS1 ThermoShaker Anleitung zur Verwendung

Short Manual Biometra ThermoShaker TS1

Analytik Jena GmbH

Konrad-Zuse-Strasse 1

07745 Jena ⋅ Germany

Phone +49 3641 77 70

[email protected]

www.analytik-jena.com

Short Manual Biometra ThermoShaker TS1

Version: A (08/2022)

34-9990-029-23

1/2

CAUTION

Risk of damage to health

The device is used to heat biological and biochemical hazardous substances to temperatures

of up to 100°C. Improper operation of the device and incorrect handling of samples may

result in injury.

¡Only use the quick reference guide together with the detailed operating manual.

¡Risk of burns from the hot block module and the samples!

¡Mix and temper samples only in sealed and heat-resistant tubes and microplates.

¡Wear personal protective equipment If samples open during operation, hot liquids may

spurt out.

Design

The thermoshaker consists of:

¡Basic device with control panel

¡Interchangeable block modules for the samples

(must be ordered separately)

The control panel has arrow keys for setting the timer, mixing frequency and temperature.

The set and actual values are shown on the display.

Timer 1minto96h, with signal tone (buzzer)

Mixing frequency 250to1400rpm

Temperature control

range

+25to+100°C

Heating rate 4°C/min (+25to+100°C)

Installation/changing a block

}Switch off the basic device safely and allow it to acclimatize.

}Select a suitable block module.

NOTICE!Switch off the device before installation/changing a block.

}Align the block module so that the labeling faces to the front.

}Connect the block module to the basic device using the 6-pin connector.

}Place the block module straight onto the basic device and fasten it with the four screws.

}Connect the device to the power outlet using the power supply unit. Switch on the device

using the ON/OFF switch at the rear of the device.

üThe device is ready for operation and immediately starts to temper the block module.

Operation

Starting the program:

}On the control panel, set the desired values for

time, mixing frequency and temperature.

}When T(°C) Actual = T(°C) Set: Place the prefilled

and sealed samples in the block module.

CAUTION!The block module can become

very hot.

}Start the program with Start/Stop Shaker.

End of program: An acoustic signal (buzzer) sounds.

}End the program with Start/Stop Shaker.

}End temperature control by entering T<25°C.

Or: Insert the next samples into the device and start a new program run.

Short Manual Biometra ThermoShaker TS1

Analytik Jena GmbH

Konrad-Zuse-Strasse 1

07745 Jena ⋅ Germany

Phone +49 3641 77 70

[email protected]

www.analytik-jena.com

Short Manual Biometra ThermoShaker TS1

Version: A (08/2022)

34-9990-029-23

2/2

Interrupting the program:

¡Use Start/Stop Timer to reset the timer to 00:00. Tap the key a second time and start

the timer again.

¡Or: Interrupt the mixing process with Start/Stop Shaker. STOP is shown on the display.

Tap the key a second time to restart the mixing process and the timer.

Operate the device using the arrow keys and the start/stop keys:

Keys Input

Time Input duration in h:min

If 00:00 is entered: continuous operation

RPM Input mixing frequency in rpm

If 000 is entered: only temperature control active

T(°C) Input block temperature in °C

If T<25°C is entered: Display: OFF, only mixer active

Start/Stop Shaker Start and stop program

Temperature control stops only after entering T<25°C.

Start/Stop Timer Reset: Set the timer to 00:00

Calibration

Calibration compensates for the different thermal conductivities of sample tubes/microplates

from different suppliers. Calibration coefficient: 0.936to1.063 (±0.063)

}Insert an empty sample tube or an empty microplate into the block module.

}Insert an external temperature sensor (±0.5°C) into the tube/well.

}Set a temperature of, e.g., 40°C, on the device.

}After 30min, compare T(°C) Actual with the sensor temperature. Calibrate the device if

there is a deviation.

Set

Actual

Time (h:min) RPM T(°C)

sct. 40.0 40.0

39.0 40.00.975

2 3

}Press the Start/Stop Timer key for longer than 8s. The calibration mode is active when

sct. (1) appears on the display.

}Adjust the temperature (3) with the arrow keys until the sensor temperature is reached

(here: 39°C). The calibration coefficient (2) adjusts itself automatically.

}Save the calibration coefficient with the Start/Stop Shaker start/stop key and exit the

calibration mode.

Maintenance

Cleaning the device:

}Switch off the device before carrying out external cleaning. Disconnect the device from

the electrical mains supply.

}Clean the housing using a slightly damp, not dripping cloth with water and commercially

available surfactants. Disinfect with ethanol (75%).

Replace the rubber belt after 1.5years or 2,000operating hours:

The rubber belt transmits the power from the shaker motor to the block module and thereby

generates the mixing movement.

}Switch off the device.

}Disconnect the plug of the external power supply.

}Carefully place the device on its side.

}Remove the base plate. To do so, loosen the four

Phillips screws.

}Change the rubber belt.

}Reassemble the base plate.

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser Proline Promass 40 Technische Daten

Endress+Hauser

Endress+Hauser Proline Promass 83 Stücklistenhandbuch

Endress+Hauser

Endress+Hauser Proline Promass A 500 PROFINET Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline Compact CM72 Technische Daten

Endress+Hauser

Endress+Hauser TOC Analyzer CA79 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass E 200 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Gammapilot FMG50 Handbuch

Endress+Hauser

Endress+Hauser Proline t-mass 65 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP51 Firmware-Update

Endress+Hauser

Endress+Hauser Deltapilot M FMB50 Technische Daten

Endress+Hauser

Endress+Hauser Levelflex M FMP40 Bedienungsanleitung

Endress+Hauser

Endress+Hauser RIA14 Technische Daten

Endress+Hauser

Endress+Hauser Proline Promag 55 PROFIBUS PA Bedienungsanleitung

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 Montageanleitung

Endress+Hauser

Endress+Hauser Smartec S CLD134 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiphant M FTL51C Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CA80CR Technische Daten

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Gebrauchsanweisung

Endress+Hauser

Endress+Hauser HART Proline Promass 80 Bedienungsanleitung

Endress+Hauser

Endress+Hauser SpectraSensors OXY5500 Benutzerhandbuch

Endress+Hauser

Endress+Hauser EngyCal RH33 Technische Daten

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 51 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung

Uniks

Uniks C126 Bedienungsanleitung