Endress+Hauser Gammapilot FMG50 Technische Daten

Products Solutions Services

Brief Operating Instructions

Gammapilot FMG50

HART

Radiometric measuring technology

These Brief Operating Instructions are not a substitute for the

Operating Instructions pertaining to the device.

Detailed information is provided in the Operating Instructions

and other documentation.

Available for all device versions via:

• Internet: www.endress.com/deviceviewer

• Smartphone/tablet: Endress+Hauser Operations app

KA01427F/00/EN/03.23-00

71623890

2023-07-10

Associated documentation Gammapilot FMG50 HART

2 Endress+Hauser

1 Associated documentation

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

2 About this document

2.1 Symbols used

2.1.1 Safety symbols

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

DANGER

Gammapilot FMG50 HART About this document

Endress+Hauser 3

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

2.1.2 Symbols for certain types of information and graphics

Warns against radioactive substances or ionizing radiation

Permitted

Procedures, processes or actions that are permitted

Forbidden

Procedures, processes or actions that are forbidden

Tip

Indicates additional information

Reference to documentation

Notice or individual step to be observed

Series of steps

Result of a step

1, 2, 3, ...

Item numbers

A, B, C, ...

Views

Visual inspection

About this document Gammapilot FMG50 HART

4 Endress+Hauser

2.2 Documentation

The following document types are available in the Downloads area of the Endress+Hauser

website (www.endress.com/downloads):

For an overview of the scope of the associated Technical Documentation, refer to the

following:

•Device Viewer (www.endress.com/deviceviewer): Enter serial number from nameplate.

•Endress+Hauser Operations app: Enter serial number from nameplate or scan matrix

code on nameplate.

2.2.1 Technical Information (TI)

Planning aid

The document contains all the technical data on the device and provides an overview of the

accessories and other products that can be ordered for the device.

2.2.2 Operating Instructions (BA)

Your reference guide

These Operating Instructions contain all the information that is required in various phases of

the life cycle of the device: from product identification, incoming acceptance and storage, to

mounting, connection, operation and commissioning through to troubleshooting,

maintenance and disposal.

2.2.3 Safety Instructions (XA)

Depending on the approval, the following Safety Instructions (XA) are supplied with the

device. They are an integral part of the Operating Instructions.

The nameplate indicates the Safety Instructions (XA) that are relevant to the device.

2.2.4 Functional Safety Manual (FY)

Depending on the SIL approval, the Functional Safety Manual (FY) is an integral part of the

Operating Instructions and applies in addition to the Operating Instructions, Technical

Information and ATEX Safety Instructions.

The different requirements that apply for the protective function are described in the

Functional Safety Manual (FY).

2.3 Registered trademarks

HART®

Registered trademark of the FieldComm Group, Austin, Texas, USA

Apple®

Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the

U.S. and other countries. App Store is a service mark of Apple Inc.

Android®

Android, Google Play and the Google Play logo are trademarks of Google Inc.

Gammapilot FMG50 HART Basic safety instructions

Endress+Hauser 5

Bluetooth®

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG,

Inc. and any use of such marks by Endress+Hauser is under license. Other trademarks and

trade names are those of their respective owners.

3 Basic safety instructions

3.1 Requirements for personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill the

following requirements:

• Trained, qualified specialists must have a relevant qualification for this specific function and

task

• Are authorized by the plant owner/operator

• Are familiar with federal/national regulations

• Before beginning work, the specialist staff must have read and understood the instructions

in the Operating Instructions and supplementary documentation as well as in the

certificates (depending on the application)

• Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

• Being instructed and authorized according to the requirements of the task by the facility's

owner-operator

• Following the instructions in these Operating Instructions

3.2 Intended use

The Gammapilot FMG50 is a compact transmitter for non-contact level, point level, density

and concentration measurement. The detector is up to 3 m (9.84 ft) in length. The

Gammapilot FMG50 is certified according to IEC 61508 for safety-related operation up to SIL

2/3.

3.3 Hazardous area

If the measuring system is used in hazardous areas, the corresponding national standards and

regulations must be observed. The device is accompanied by separate "Ex documentation",

which is an integral part of these Operating Instructions. The installation specifications,

connection values and safety instructions listed in this supplementary documentation must be

observed.

• Technical personnel must be qualified and trained for the hazardous area.

• Comply with the metrological and safety-related requirements for the measuring point.

LWARNING

‣Observe the safety instructions associated with the device. These instructions depend on

the certificate ordered

Basic safety instructions Gammapilot FMG50 HART

6 Endress+Hauser

3.4 Radiation protection

The Gammapilot FMG50 is used in conjunction with a radioactive source, fitted in a source

container. The Gammapilot FMG50 does not emit any radioactive radiation. Observe the

following instructions when handling radioactive sources:

3.4.1 Basic radiation protection guidelines

LWARNING

‣When working with radioactive sources, avoid any unnecessary exposure to radiation. All

unavoidable radiation exposure must be kept to a minimum. Three basic concepts apply to

achieve this:

ABC

A0016373

A Shielding

B Time

C Distance

LCAUTION

‣When working with source containers, all the instructions for mounting and usage outlined

in the following documents must be observed:

Source container documentation

•FQG60:

TI00445F

•FQG61, FQG62:

TI00435F

•FQG63:

TI00446F

•FQG66:

• TI01171F

• BA01327F

Gammapilot FMG50 HART Basic safety instructions

Endress+Hauser 7

Shielding

Ensure the best possible shielding between the radiation source and yourself and all other

person. Effective shielding is provided by source containers (FQG60, FQG61/FQG62,FQG63,

FQG66) and all high-density materials (lead, iron, concrete etc.).

Time

Remain as short as possible in the area exposed to radiation.

Distance

Keep as far away from the radiation source as possible. The radiation intensity decreases in

proportion to the square of the distance from the radiation source.

3.5 Workplace safety

When working on and with the device:

‣Wear the required personal protective equipment as per national regulations.

‣Switch off the supply voltage before connecting the device.

3.6 Operational safety

Risk of injury!

‣Operate the device only if it is in proper technical condition, free from errors and faults.

‣The operator is responsible for ensuring trouble-free operation of the device.

3.7 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the-art safety requirements, has been tested, and left the factory in a condition in which it

is safe to operate. It meets general safety standards and legal requirements.

The manufacturer confirms successful testing of the device by affixing to it the CE mark, the

UKCA mark, the C-Tick mark and the EAC mark.

3.8 Supplementary safety instructions

LCAUTION

Devices with version NaI(TI) contain more than 0.1% sodium iodide and are recorded in

the CAS No. 7681-82-5 safety data sheet.

‣The sodium iodide is generally not accessible and fully encapsulated. Ensure full

compliance with the safety instructions in the CAS No.7681-82-5 safety data sheet if the

encapsulation of the sodium iodide within the device is damaged.

Incoming acceptance and product identification Gammapilot FMG50 HART

8 Endress+Hauser

4 Incoming acceptance and product identification

4.1 Incoming acceptance

Check the following during incoming acceptance:

• Are the order codes on the delivery note and the product sticker identical?

• Are the goods undamaged?

• Does the data on the nameplate match the order specifications on the delivery note?

• If required (see nameplate), are the Safety Instructions (XA) provided?

If any one of these conditions is not met, contact your Endress+Hauser Sales Center.

4.1.1 Product identification

The following options are available for identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

‣Enter serial number from nameplates in W@M Device Viewer

(www.endress.com/deviceviewer)

 All of the information on the measuring device and on the scope of the technical

documentation pertaining to the device is displayed.

‣Enter the serial number from the nameplate into the Endress+Hauser Operations App or

scan the 2-D matrix code on the nameplate.

 All of the information on the measuring device and on the scope of the technical

documentation pertaining to the device is displayed.

4.1.2 Manufacturer address

Endress+Hauser SE+Co. KG

Hauptstraße 1

79689 Maulburg, Germany

Place of manufacture: See nameplate.

4.2 Transport, storage and disposal

4.2.1 Storage conditions

Pack the device so that is protected against impact for storage and transport. The original

packaging offers the best protection for this. The permitted storage temperature is:

NaI (Tl) crystal

–40 to +80 °C (–40 to +176 °F)

PVT scintillator (standard)

–40 to +60 °C (–40 to +140 °F)

Gammapilot FMG50 HART Mounting

Endress+Hauser 9

PVT scintillator (high-temperature version)

–20 to +80 °C (–4 to +176 °F)

As the device contains a battery, it is recommended to store the device at room

temperature in a location that does not receive direct sunlight

4.2.2 Transporting to the measuring point

LCAUTION

Risk of injury

‣Follow the safety instructions and transport conditions for devices weighing more than

18 kg (39.69 lb).

4.2.3 Disposal

If required by the Directive 2012/19/EU on waste electrical and electronic equipment

(WEEE), our products are marked with the depicted symbol in order to minimize the

disposal of WEEE as unsorted municipal waste. Such products may not be disposed of as

unsorted municipal waste and can be returned to Endress+Hauser for disposal at conditions

stipulated in our General Terms and Conditions or as individually agreed.

Battery disposal

• The end user is legally obliged to return used batteries.

• The end user can return old batteries or electronic assemblies containing these batteries

free of charge to Endress+Hauser.

In accordance with German law regulating the use of batteries (BattG §28 Para 1 Number

3), this symbol is used to denote electronic assemblies that must not be disposed of as

household waste.

5 Mounting

LWARNING

‣The four screws connecting the detector pipe to the terminal head may not be opened.

Mounting Gammapilot FMG50 HART

10 Endress+Hauser

A0038007

5.1 Mounting requirements

5.1.1 General information

• The angle of emission of the source container must be exactly aligned to the measuring

range of the Gammapilot FMG50. Observe the measuring range marks of the device.

• The source container and the Gammapilot FMG50 should be mounted as close to the vessel

as possible. Any access to the beam must be blocked to ensure that it is not possible to reach

into this area.

• The Gammapilot FMG50 should be protected against direct sunlight or process heat in

order to increase its service life.

• Feature 620, option PA: "Weather protection cover 316L"

• Feature 620, option PV: "Heat shield 1200-3000 mm, PVT"

• Feature 620, option PW: "Heat shield NaI, 200-800 mm, PVT"

• Terminals can optionally be ordered with the device

• The mounting device must be installed in such a way as to withstand the weight of the

Gammapilot FMG50 under all anticipated operating conditions (e.g. vibrations).

More information with regard to the safety-related use of the Gammapilot FMG50 can

be found in the Functional Safety Manual.

In addition to the dimensions and weights, the mounting requirements for level measurement

and point level measurement are described in the following section.

Mounting requirements for

• Density measurement

• Interface measurement

• Density profile measurement (DPS)

• Concentration measurement

• Concentration measurement with radiating media

• Flow measurements

are described in the Operating Instructions.

Andere Handbücher für Gammapilot FMG50

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser micropilot M FMR 231 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CNGmass DCI Bedienungsanleitung

Endress+Hauser

Endress+Hauser QWX43 Bedienerhandbuch

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot FMR56 Handbuch

Endress+Hauser

Endress+Hauser Cerabar S PMP72 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 83 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Prowirl C 200 Technische Daten

Endress+Hauser

Endress+Hauser SmarTec S CLD 132 PROFIBUS-PA Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar PMD55B Technische Daten

Endress+Hauser

Endress+Hauser Proline Promass 84 MODBUS RS485 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP51 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Handbuch

Endress+Hauser

Endress+Hauser Teqwave H Bedienungsanleitung

Endress+Hauser

Endress+Hauser Flowphant T DTT31 Handbuch

Endress+Hauser

Endress+Hauser Levelflex FMP51 Technische Daten

Endress+Hauser

Endress+Hauser Proline t-mass 65 PROFIBUS DP Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 80 Anwendungshandbuch

Endress+Hauser

Endress+Hauser Proline Promag 50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 91W Handbuch

Endress+Hauser

Endress+Hauser Promag 300 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Endress+Hauser

Endress+Hauser Endress+Hauser Technische Daten

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung