Endress+Hauser Proline Promass 300 Bedienerhandbuch

Products Solutions Services

Special Documentation

Proline Promass 300

PROFIBUS DP

Web server

SD02226D/06/EN/01.18

71402820

Valid as of version

01.00.zz (Device firmware)

Proline Promass 300 PROFIBUS DP Table of contents

Endress+Hauser 3

Table of contents

1 About this document ................ 4

1.1 Document function ..................... 4

1.2 Target group .......................... 4

1.3 Using this document .................... 4

1.4 Symbols used .......................... 4

2 Basic safety instructions ............ 6

2.1 Requirements for personnel ............... 6

2.2 Designated use ........................ 6

2.3 Occupational safety ..................... 6

2.4 Operational safety ...................... 6

2.5 Product safety ......................... 6

2.6 IT security ............................ 7

2.7 Device-specific IT security ................. 7

3 Product features and availability ... 10

3.1 Product features ...................... 10

3.2 Availability .......................... 10

3.3 Identification in the measuring device ...... 10

4 Commissioning .................... 11

4.1 Prerequisites - computer ................ 11

4.2 Prerequisites - measuring device .......... 17

4.3 Connecting the computer to the measuring

device .............................. 17

4.4 Establishing a connection to the Web

server .............................. 19

4.5 Setting the IP address .................. 20

4.6 Overview of the Web server parameters ..... 20

5 Operation options ................. 23

5.1 Logging on .......................... 23

5.2 User interface ........................ 24

5.3 Logging out .......................... 25

6 Diagnostics and troubleshooting ... 26

6.1 General Web server troubleshooting ........ 26

6.2 Diagnostic information in the Web browser .. 27

6.3 Diagnostic information in the measuring

device .............................. 28

6.4 Checking the network connection .......... 28

7 Technical data .................... 29

About this document Proline Promass 300 PROFIBUS DP

4 Endress+Hauser

1 About this document

1.1 Document function

This manual is a Special Documentation; it does not replace the Operating Instructions

pertaining to the device. It serves as a reference for using the Web server integrated in the

measuring device.

1.2 Target group

The document is aimed at specialists who work with the device over the entire life cycle

and perform specific configurations.

1.3 Using this document

1.3.1 Information on the document structure

This Special Documentation contains a range of information, including:

• Prerequisites for use on the computer and measuring device

• Connection of the computer via the service interface or WLAN interface

• Configuration of the communication interface

• Establishing a connection

• Diagnostics and troubleshooting

The information and safety instructions in the Operating Instructions pertaining to

the measuring device must always be observed →  4.

1.3.2 Device documentation

The Technical Documentation for the measuring device is available:

• On the CD-ROM supplied with the measuring device (depending on the device version,

the CD-ROM might not be part of the delivery!)

• Via the W@M Device Viewer: enter the serial number from the nameplate

(www.endress.com/deviceviewer)

• Via the Endress+Hauser Operations App: enter the serial number from the nameplate or

scan the 2-D matrix code (QR code) on the nameplate.

Technical documentation can also be downloaded from the Download Area of the

Endress+Hauser web site: www.endress.com → Download. However this technical

documentation applies to a particular instrument family and is not assigned to a

specific measuring device.

1.4 Symbols used

1.4.1 Safety symbols

Symbol Meaning

DANGER

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will

result in serious or fatal injury.

WARNING

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can

result in serious or fatal injury.

Proline Promass 300 PROFIBUS DP About this document

Endress+Hauser 5

Symbol Meaning

CAUTION

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can

result in minor or medium injury.

NOTICE

NOTE!

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.4.2 Symbols for certain types of information

Symbol Meaning

Permitted

Indicates procedures, processes or actions that are allowed.

Forbidden

Indicates procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

Reference to documentation

Reference to page

Reference to graphic

Notice or individual step to be observed

… Series of steps

Result of a step

1.4.3 Symbols in graphics

Symbol Meaning

1, 2, 3,... Item numbers

… Series of steps

Basic safety instructions Proline Promass 300 PROFIBUS DP

6 Endress+Hauser

2 Basic safety instructions

2.1 Requirements for personnel

Personnel involved in installation, commissioning, diagnostics and maintenance must

meet the following requirements:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the

application)

‣Follow instructions and comply with basic conditions

Operating personnel must meet the following requirements:

‣Be instructed and authorized by the plant operator with regard to the requirements of

the task

‣Follow the instructions in this manual

2.2 Designated use

The designated use of the measuring device is described in the Operating Instructions

pertaining to the device →  4.

2.3 Occupational safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

If working on and with the device with wet hands:

‣It is recommended to wear gloves on account of the higher risk of electric shock.

2.4 Operational safety

Risk of injury!

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers.

‣If, despite this, modifications are required, consult with Endress+Hauser.

2.5 Product safety

This device is designed in accordance with good engineering practice to meet state-of-the-

art safety requirements, has been tested, and left the factory in a condition in which it is

safe to operate.

It meets general safety standards and legal requirements. It also complies with the EC

directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser

confirms this by affixing the CE mark to the device.

Proline Promass 300 PROFIBUS DP Basic safety instructions

Endress+Hauser 7

2.6 IT security

Our warranty is valid only if the device is installed and used as described in the Operating

Instructions. The device is equipped with security mechanisms to protect it against any

inadvertent changes to the settings.

IT security measures, which provide additional protection for the device and associated

data transfer, must be implemented by the operators themselves in line with their security

standards.

2.7 Device-specific IT security

The device offers a range of specific functions to support protective measures on the

operator's side. These functions can be configured by the user and guarantee greater in-

operation safety if used correctly. An overview of the most important functions is provided

in the following section.

Function/interface Factory setting Recommendation

Write protection via hardware write

protection switch →  7

Not enabled. On an individual basis following risk

assessment.

Access code

(also applies for Web server login or

FieldCare connection) →  8

Not enabled

(0000).

Assign a customized access code during

commissioning.

WLAN

(order option in display module)

Enabled. On an individual basis following risk

assessment.

WLAN security mode Enabled (WPA2-

PSK)

Do not change.

WLAN passphrase

(password) →  8

Serial number Assign a customized access code during

commissioning.

WLAN mode Access Point On an individual basis following risk

assessment.

Web server→  8 Enabled. On an individual basis following risk

assessment.

CDI-RJ45 service interface →  8 – On an individual basis following risk

assessment.

2.7.1 Protecting access via hardware write protection

Write access to the device parameters via the local display, Web browser or operating tool

(e.g. FieldCare, DeviceCare) can be disabled via a write protection switch (DIP switch on

the motherboard). When hardware write protection is enabled, only read access to the

parameters is possible.

Hardware write protection is disabled when the device is delivered.

2.7.2 Protecting access via a password

Different passwords are available to protect write access to the device parameters or access

to the device via the WLAN interface.

Basic safety instructions Proline Promass 300 PROFIBUS DP

8 Endress+Hauser

• User-specific access code

Protect write access to the device parameters via the local display, Web browser or

operating tool (e.g. FieldCare, DeviceCare). Access authorization is clearly regulated

through the use of a user-specific access code.

• WLAN passphrase

The network key protects a connection between an operating unit (e.g. notebook or

tablet) and the device via the WLAN interface which can be ordered as an option.

• Infrastructure mode

When the device is operated in infrastructure mode, the WLAN passphrase corresponds

to the WLAN passphrase configured on the operator side.

User-specific access code

Write access to the device parameters via the local display, Web browser or operating tool

(e.g. FieldCare, DeviceCare) can be protected by the modifiable, user-specific access code.

When the device is delivered, the device does not have an access code and is equivalent to

0000 (open).

WLAN passphrase: Operation as WLAN access point

A connection between an operating unit (e.g. notebook or tablet) and the device via the

WLAN interface, which can be ordered as an optional extra, is protected by the network

key. The WLAN authentication of the network key complies with the IEEE 802.11

standard.

When the device is delivered, the network key is pre-defined depending on the device. It

can be changed via the WLAN settings submenu in the WLAN passphrase parameter.

Infrastructure mode

A connection between the device and WLAN access point is protected by means of an SSID

and passphrase on the system side. Please contact the relevant system administrator for

access.

General notes on the use of passwords

• The access code and network key supplied with the device should be changed during

commissioning.

• Follow the general rules for generating a secure password when defining and managing

the access code or network key.

• The user is responsible for the management and careful handling of the access code and

network key.

2.7.3 Access via Web server

The Web server is enabled when the device is delivered. The Web server can be disabled if

necessary (e.g. after commissioning) via the Web server functionality parameter.

The device and status information can be hidden on the login page. This prevents

unauthorized access to the information.

For detailed information on device parameters, see:

The "Description of Device Parameters" document

2.7.4 Access via service interface (CDI-RJ45)

The device can be connected to a network via the service interface (CDI-RJ45). Device-

specific functions guarantee the secure operation of the device in a network.

The use of relevant industrial standards and guidelines that have been defined by national

and international safety committees, such as IEC/ISA62443 or the IEEE, is recommended.

Proline Promass 300 PROFIBUS DP Basic safety instructions

Endress+Hauser 9

This includes organizational security measures such as the assignment of access

authorization as well as technical measures such as network segmentation.

Product features and availability Proline Promass 300 PROFIBUS DP

10 Endress+Hauser

3 Product features and availability

3.1 Product features

Thanks to the integrated Web server, the device can be operated and configured via a Web

browser and via a service interface (CDI-RJ45) or via a WLAN interface. The structure of

the operating menu is the same as for the local display. In addition to the measured values,

status information on the device is also displayed and allows the user to monitor the status

of the device. Furthermore the device data can be managed and the network parameters

can be configured.

A device that has a WLAN interface (can be ordered as an option) is required for the

WLAN connection: order code for "Display; operation", option G "4-line, illuminated; touch

control + WLAN". The device acts as an Access Point and enables communication by

computer or a mobile handheld terminal.

3.2 Availability

The integrated Web server is a standard feature. It does not need to be ordered for the

device ex works as it is provided as standard when the device is delivered to the customer.

No particular measures are required to put the feature into operation.

3.3 Identification in the measuring device

An adhesive label on the inside of the electronics compartment cover or the connection

compartment describes all the available hardware components, and their functions, for the

measuring device. The service interface (CDI-RJ45) has the following identification:

Service Int. (CDI)

IP 192.168.1.212

A0030874

 1 Example of the CDI-RJ45 service interface

1 Symbol for service interface

2 Information on the default setting for the WLAN IP address

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser Levelflex M FMP40 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP43 Bedienungsanleitung

Endress+Hauser

Endress+Hauser SmarTec S CLD 132 PROFIBUS-PA Bedienungsanleitung

Endress+Hauser

Endress+Hauser micropilot M FMR 230 Handbuch

Endress+Hauser

Endress+Hauser LT1100 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CAT860 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prothermo NMT532 Handbuch

Endress+Hauser

Endress+Hauser SpectraSensors OXY5500 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Technische Daten

Endress+Hauser

Endress+Hauser Nivocompact FTC 131 Handbuch

Endress+Hauser

Endress+Hauser Liquiline System CA80AL Technische Daten

Endress+Hauser

Endress+Hauser Solicap M FTI56 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag H 100 EtherNet/IP Technische Daten

Endress+Hauser

Endress+Hauser Gammapilot FMG50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP40 Anwendungshandbuch

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 83 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar M PMC41 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP41C Bedienungsanleitung

Endress+Hauser

Endress+Hauser promag 31 Bedienungsanleitung

Endress+Hauser

Endress+Hauser SpectraSensors SS2100i-1 Benutzerhandbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung

Uniks

Uniks C126 Bedienungsanleitung