Endress+Hauser Prosonic M FMU41 Technische Daten

Products Solutions Services

Brief Operating Instructions

Prosonic M FMU41

HART

Ultrasonic measuring technology

These Instructions are Brief Operating Instructions; they are

not a substitute for the Operating Instructions pertaining to

the device.

Detailed information about the device can be found in the

Operating Instructions and the other documentation:

Available for all device versions via:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

KA01423F/00/EN/01.22-00

71571000

2022-04-04

Associated documentation Prosonic M FMU41 HART

2 Endress+Hauser

1 Associated documentation

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

2 About this document

2.1 Symbols

2.1.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

Prosonic M FMU41 HART Basic safety instructions

Endress+Hauser 3

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

2.1.2 Electrical symbols

Ground connection

Grounded clamp, which is grounded via a grounding system.

Protective earth (PE)

Ground terminals, which must be grounded prior to establishing any other connections. The

ground terminals are located on the inside and outside of the device.

Temperature resistance of the connection cables

Minimum value for the temperature resistance of the connection cables

2.1.3 Symbols for certain types of information and graphics

Permitted

Procedures, processes or actions that are permitted.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

Reference to documentation

Series of steps

Result of an individual step

1, 2, 3 ... Item numbers

3 Basic safety instructions

3.1 Requirements for the personnel

To carry out their tasks, such as commissioning or maintenance, personnel must meet the

following requirements:

‣Trained specialists must have a qualification that is relevant to the specific function and

task.

Basic safety instructions Prosonic M FMU41 HART

4 Endress+Hauser

‣Must be authorized by the plant owner/operator.

‣Must be familiar with national regulations.

‣Must have read and understood the instructions in the manual and supplementary

documentation.

‣Must follow instructions and comply with general policies.

3.2 Intended use

Compact measuring device for continuous, non-contact level measurement. The measuring

range is up to 8 m (26 ft) for liquids and up to 3.5 m (11 ft) for bulk solids. Flow

measurements can be carried out in open flumes and weirs with the linearization function.

3.3 Workplace safety

When working on and with the device:

‣Wear the required protective equipment according to federal/national regulations.

3.4 Operational safety

Risk of injury!

‣Operate the device only if it is in proper technical condition, free from errors and faults.

‣The operator is responsible for the trouble-free operation of the device.

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers.

‣If modifications are nevertheless required, consult with Endress+Hauser.

Repair

To ensure continued operational safety and reliability:

‣Only perform repair work on the device if this is expressly permitted.

‣Observe federal/national regulations pertaining to the repair of an electrical device.

‣Use original spare parts and accessories from Endress+Hauser only.

3.5 Product safety

This device has been constructed and tested to state-of-the-art operational safety standards

and in accordance with good engineering practice. The device left the factory in a safe

operating condition.

3.5.1 CE mark

The device meets the legal requirements of the applicable EU Directives. These are listed in

the corresponding EU Declaration of Conformity along with the standards applied.

Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.

Prosonic M FMU41 HART Incoming acceptance and product identification

Endress+Hauser 5

3.5.2 EAC conformity

The device meets the legal requirements of the applicable EAC Directives. These are listed in

the corresponding EAC Declaration of Conformity along with the standards applied.

Endress+Hauser confirms successful testing of the device by affixing to it the EAC mark.

3.6 IT security

We only provide a warranty if the device is installed and used as described in the Operating

Instructions.

Provide additional protection for the device and data transfer to/from the device

‣IT security measures defined in the plant owner/operator's own security policy must be

implemented by plant owners/operators themselves.

4 Incoming acceptance and product identification

4.1 Incoming acceptance

Check the following during goods acceptance:

 Are the order codes on the delivery note and the product sticker identical?

 Are the goods undamaged?

 Do the nameplate data match the ordering information on the delivery note?

 If necessary (see nameplate), are the Safety Instructions, e. g. XA, provided?

If one of these conditions is not satisfied, contact your Sales Center.

4.2 Product identification

The following options are available for identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

‣Enter serial number from nameplates in W@M Device Viewer

(www.endress.com/deviceviewer)

 All of the information on the measuring device and on the scope of the technical

documentation pertaining to the device is displayed.

‣Enter the serial number from the nameplate into the Endress+Hauser Operations App or

scan the 2-D matrix code on the nameplate.

 All of the information on the measuring device and on the scope of the technical

documentation pertaining to the device is displayed.

Incoming acceptance and product identification Prosonic M FMU41 HART

6 Endress+Hauser

4.3 Manufacturer address

Endress+Hauser SE+Co. KG

Hauptstraße 1

79689 Maulburg, Germany

Place of manufacture: See nameplate.

4.4 Storage and transport

• Pack the measuring device so that it is protected against impact.

The original packaging offers the best protection

• Permitted storage temperature: –40 to +80 °C (–40 to 176 °F)

4.4.1 Transporting the product to the measuring point

LCAUTION

The housing or flange can be damaged.

Risk of injury!

‣Transport the measuring device to the measuring point in its original packaging or by the

process connection.

‣Always secure lifting equipment (belts, lugs, etc.) at the process connection, while paying

attention to the center of gravity of the device to ensure that the device does not tilt or slip.

‣Follow the safety instructions and transport conditions for devices weighing more than

18 kg (39.6 lb)(IEC 61010).

Prosonic M FMU41 HART Mounting

Endress+Hauser 7

5 Mounting

5.1 Mounting requirements

5.1.1 Installation conditions for sensor for level measurements

A0038210

 1 Installation conditions

1 Distance to vessel wall: ¹⁄₆ of vessel diameter

2 Use of a weather protection cover; protection from direct sunlight or rain

3 Do not install the sensor in the middle of the vessel.

4 Avoid measurements through the filling curtain.

5 Do not install limit switches or temperature sensors inside the beam angle.

6 Measurement is affected by symmetrical fittings, e.g. heating coils and baffles.

7 Position the sensor so that it is perpendicular to the product surface.

• Install only one device per vessel: signals from multiple devices will interfere with each

other.

• Determine the detection range using a 3 dB beam angle α.

Further information is available in the Operating Instructions.

5.1.2 Installation conditions for the sensor for flow measurements

• Mount the measuring device on the upstream side immediately above the maximum upper

water level Hmax

• Take the blocking distance into account

• Position the measuring device in the center of the flume or weir

Mounting Prosonic M FMU41 HART

8 Endress+Hauser

• Align the sensor membrane so that it is parallel to the surface of the water

• Observe the installation clearance of the flume or weir

• Enter the "flow - level" ("Q/h curve") linearization curve via the FieldCare operating program

or manually via the local display

1 x b

B C

Hmax = F

A0038222

 2 Khafagi-Venturi flume (example)

A Khafagi-Venturi flume

B Upstream side

C Downstream side

BD Blocking distance of the sensor

E Empty calibration (enter during commissioning)

Hmax Maximum upstream level

V Flow

b0Width of Khafagi-Venturi flume

Prosonic M FMU41 HART Mounting

Endress+Hauser 9

≥ 2 Hmax

Hmax (= F)

≥3 Hmax

A0038223

 3 Triangular weir (example)

BD Blocking distance of the sensor

E Empty calibration (enter during commissioning)

F Full calibration

Hmax Maximum upstream level

Mounting Prosonic M FMU41 HART

10 Endress+Hauser

5.1.3 Mounting examples

C D

A0038234

 4 Mounting examples

A With counter nut

B With welding boss

C With mounting bracket

D With screw-in flange

5.1.4 Mounting the device

NOTICE

The device can be damaged.

‣Tighten the device at the threaded boss only, with maximum 20 Nm (14.75 lbf ft).

Andere Handbücher für Prosonic M FMU41

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser Levelflex M FMP41C Bedienungsanleitung

Endress+Hauser

Endress+Hauser SpectraSensors OXY5500 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar S FMD76 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline t-mass 65F Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93T Portable Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Gebrauchsanweisung

Endress+Hauser

Endress+Hauser Liquiline System CA80HA Bedienungsanleitung

Endress+Hauser

Endress+Hauser Solitrend MMP20 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquitrend QMW43 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar M PMC51? Cerabar M PMP51 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 10 Technische Daten

Endress+Hauser

Endress+Hauser LT5 Bedienungsanleitung

Endress+Hauser

Endress+Hauser magphant Bedienungsanleitung

Endress+Hauser

Endress+Hauser SpectraSensors SS2100r Bedienungsanleitung

Endress+Hauser

Endress+Hauser StamoLys CA 71 AM Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar M PMC41 Handbuch

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Solicap M FTI56 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proservo NMS83 Technische Daten

Endress+Hauser

Endress+Hauser Hart Cerabar PMP71B Bedienungsanleitung

Endress+Hauser

Endress+Hauser Conducal CLY421 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung