Endress+Hauser Proline t-mass 65F Bedienungsanleitung

BA112D/06/en/12.05

71009066

Valid as of version:

V 1.00.XX (device software)

Description of Device Functions

Proline t-mass 65F, 65I

Thermal Mass Flow Measuring System

Device Functions Proline t-mass 65

2Endress+Hauser

Device Functions Proline t-mass 65 Table of Contents

Endress+Hauser 3

Table of Contents

1 Function matrix Proline t-mass 65 . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 The function matrix: layout and use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Graphical illustration of the function matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Group MEASURING VALUES . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 Group SYSTEM UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 Group SPECIAL UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Group QUICK SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.1 Quick Setup Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

6 Group OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

7 Group USER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

8 Group TOTALIZER 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

9 Group HANDLING TOTALIZER . . . . . . . . . . . . . . . . . . . . . . . . . 23

10 Group CURRENT OUTPUT 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . 24

11 Group PULSE/FREQUENCY OUTPUT . . . . . . . . . . . . . . . . . . . . 28

12 Group RELAY OUTPUT 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

12.1 Information on the response of the relay output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

12.2 Switching response of the relay output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

13 Group STATUS INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

14 Group CURRENT INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

15 Group COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

16 Group PROCESS PARAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . 55

17 Group GAS MIXTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

18 Group SYSTEM PARAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

19 Group SENSOR DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

20 Group SUPERVISION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Table of Contents Device Functions Proline t-mass 65

4Endress+Hauser

21 Group SIMULATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . 68

22 Group SENSOR VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

23 Group AMPLIFIER VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

24 Factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

24.1 SI units (not for USA and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

24.2 US units (only for USA and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

25 Index of key words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Device Functions Proline t-mass 65 1 Function matrix Proline t-mass 65

Endress+Hauser 5

1 Function matrix Proline t-mass 65

1.1 The function matrix: layout and use

The function matrix is a two-level construct: the groups form one level, functions the other.

The groups are the highest-level grouping of the control options for the flowmeter.

Each group comprises a number of functions.

You select a group in order to access the individual functions for controlling or parameterizing the

flowmeter.

You will find an overview of the groups in the table of contents on Page 3 and in the graphical

representation of the function matrix on Page 6.

You will also find an overview of the functions on Page 6, complete with the page references of the

detailed function descriptions.

The descriptions of the individual functions start on Page 8.

Example of how to parameterize a function (in this case changing the language for

the user interface):

➀Entry into the function matrix (F-key).

➁Select the OPERATION group.

➂Select the LANGUAGE function, change the setting from ENGLISH to DEUTSCH

with OS and save F(all texts displayed on the user interface appear in German).

➃Exit the function matrix (ESC > 3 seconds).

A0001142

>3s

-+E

Esc

E E E E E

–

Esc

–

Esc

–

Esc

–

1 Function matrix Proline t-mass 65 Device Functions Proline t-mass 65

6Endress+Hauser

1.2 Graphical illustration of the function matrix

ACTUAL FREQUENCY

(p. 33)

ASSIGN STATUS

(p. 40)

TEST DISPLAY

(p. 20)

VALUE SIMULATION

CURRENT (p. 27)

FAILSAFE VALUE

(p. 33)

VALUE SIMULATION

PULSE (p. 40)

REFERENCE DENSITY

(p. 57)

UNIT LENGTH

(p. 11)

BACKLIGHT

(p. 20)

SIMULATION CURRENT

(p. 27)

FAILSAFE MODE

(p. 33)

SIMULATION PULSE

(p. 39)

VALUE SIMULATION

CURRENT INPUT (p. 51)

DEVICE REVISION

(p. 54)

REFERENCE PRESSURE

(P. 57)

UNIT DENSITY

(p. 11)

CONTRAST LCD

(p. 19)

ACTUAL CURRENT

(p. 27)

TIME CONSTANT

(p. 33)

FAILSAFE MODE

(p. 39)

VALUE SIMULATION

SWITCH POINT (p. 45)

SIMULATION CUR-

RENT INPUT (p. 51)

DEVICE ID

(p. 53)

REFERENCE TEMPERA-

TURE (p. 57)

UNIT TEMPERATURE

(p. 11)

DISPLAY DAMPING

(p. 19)

FAILSAFE MODE

(p. 27)

OUTPUT SIGNAL

(p. 30)

OUTPUT SIGNAL

(p. 36)

VALUE SIMULATION

SWITCH POINT (p. 42)

SIMULATION SWITCH

POINT (p. 44)

VALUE SIMULATION

STATUS INPUT (p. 49)

ACTUAL CURRENT

INPUT (p. 51)

MANUFACTURER ID

(p. 53)

PROCESS PRESSURE

(p. 56)

UNIT PRESSURE

(p. 11)

ACCESS CODE

COUNTER (p. 17)

FORMAT

(p. 19)

RESET TOTALIZER

(p. 22)

TIME CONSTANT

(p. 26)

VALUE f HIGH

(p. 29)

PULSE WIDTH

(p. 35)

SIMULATION SWITCH

POINT (p. 42)

ACTUAL STATUS RELAY

(p. 44)

SIMULATION STATUS

INPUT (p. 49)

FAILSAFE VALUE

(p. 51)

WRITE PROTECTION

(p. 53)

INSTALLATION FAC-

TOR (p. 56)

UNIT CORRECTED

VOLUME (p. 10)

STATUS ACCESS

(p. 16)

100% VALUE LINE 2

(p. 19)

UNIT TOTALIZER

(p. 22)

VALUE 20 mA

(p. 25)

VALUE f LOW

(p. 29)

PULSE VALUE

(p. 35)

ACTUAL STATUS

(p. 41)

TIME CONSTANT

(p. 44)

ACTUAL STATUS INPUT

(p. 48)

VALUE 20 mA

(p. 51)

HART PROTOCOL

(p. 53)

ZERO POINT ADJUST

(p. 56)

TEMPERATURE

(p. 8)

UNIT CORRECTED

VOLUME FLOW (p. 10)

DEFINE PRIVATE CODE

(p. 16)

100% VALUE LINE 1

(p. 18)

OVERFLOW

(p. 21)

VALUE 0_4 mA

(p. 25)

END VALUE

FREQUENCY (p. 28)

ASSIGN PULSE

(p. 34)

TIME CONSTANT

(p. 41)

OFF-VALUE

(p. 44)

MINIMUM PULSE

WIDTH (p. 48)

VALUE 0_4 mA

(p. 50)

FIELDBUS ADDRESS

(p. 53)

OFF VALUE LOW FLOW

CUT OFF (p. 55)

CORRECTED VOLUME

FLOW (p. 8)

UNIT MASS

(p. 9)

FACTOR ARBITRARY

MASS (p. 12)

T-DAT SAVE/LOAD

(p. 13)

ACCESS CODE

(p. 16)

ASSIGN LINE 2

(p. 18)

SUM

(p. 21)

FAILSAFE MODE

(p. 23)

CURRENT SPAN

(p. 24)

ASSIGN FREQUENCY

(p. 28)

VALUE SIMULATION

FREQUENCY (p. 34)

OFF-VALUE

(p. 41)

ON-VALUE

(p. 43)

ACTIVE LEVEL

(p. 48)

CURRENT SPAN

(p. 50)

TAG DESCRIPTION

(p. 53)

ON VALUE LOW FLOW

CUT OFF (p. 55)

MASS FLOW

(p. 8)

UNIT MASS FLOW

(p. 9)

TEXT ARBITRARY MASS

(p. 12)

QUICK SETUP

COMMISSION (p. 13)

LANGUAGE

(p. 16)

ASSIGN LINE 1

(p. 18)

ASSIGN TOTALIZER

(p. 21)

RESET ALL TOTALIZ-

ERS (p. 23)

ASSIGN CURRENT

(p. 24)

OPERATION MODE

(p. 28)

SIMULATION

FREQUENCY (p. 34)

ON-VALUE

(p. 41)

ASSIGN RELAY

(p. 43)

ASSIGN STATUS INPUT

(p. 48)

ASSIGN CURRENT

INPUT (p. 50)

TAG NAME

(p. 53)

ASSIGN LOW FLOW

CUT OFF (p. 55)

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

MEASURING VALUES

(p. 8)

SYSTEM UNITS

(p. 9)

SPECIAL UNITS

(p. 12)

QUICK SETUP

(p. 13)

OPERATION

(p. 16)

USER INTERFACE

(p. 18)

TOTALIZER 1/2

(p. 21)

HANDLING TOTALIZER

(p. 23)

CURRENT OUTPUT 1/2

(p. 24)

PULSE/FREQ. OUT.

(p. 28)

RELAY OUTPUT 1/2

(p. 43)

STATUS INPUT

(p. 48)

CURRENT INPUT

(p. 50)

COMMUNICATION

(p. 53)

PROCESS PARAM.

(p. 55)

▼

Device Functions Proline t-mass 65 1 Function matrix Proline t-mass 65

Endress+Hauser 7

GAS TYPE 5

(p. 60)

HOURS SINCE RESET

(p. 67)

% FRACTION 4

(p. 60)

SAVE CHANGES

(p. 62)

OPERATION HOURS

(p. 67)

GAS TYPE 4

(p. 60)

CHECK VALUES

(p. 62)

SYSTEM RESET

(p. 67)

SOFTWARE REV NO

SUB-I/O TYPE (p. 70)

% FRACTION 3

(p. 60)

% FRACTION 8

(p. 62)

FLOW CONDITIONER

(p. 65)

ALARM DELAY

(p. 67)

SUB-I/O TYPE

(p. 70)

GAS TYPE 3

(p. 60)

GAS TYPE 8

(p. 62)

ZERO POINT

(p. 65)

ERROR CATEGORY

(p. 66)

PRE-AMPLIFIER HARD-

WARE REV. NO. (p. 69)

SOFTWARE REV. NO.

I/O MODULE (p. 70)

% FRACTION 2

(p. 59)

% FRACTION 7

(p. 61)

INTERNAL WIDTH

(p. 65)

ASSIGN PROCESS

ERROR (p. 66)

PRE-AMPLIFIER SOFT-

WARE REV. NO. (p. 69)

I/O MODULE TYPE

(p. 70)

GAS TYPE 2

(p. 59)

GAS TYPE 7

(p. 61)

INTERNAL HEIGHT

(p. 65)

ERROR CATEGORY

(p. 66)

SOFTWARE REVISION

NUMBER S-DAT (p. 69)

SOFTWARE REVISION

NUMBER T-DAT (p. 70)

% FRACTION 1

(p. 59)

% FRACTION 6

(p. 61)

INTERNAL DIAMETER

(p. 64)

ASSIGN SYSTEM ERROR

(p. 66)

VALUE SIMULATION

MEASURAND (p. 68)

TRANSDUCER SERIAL

NUMBER (p. 69)

SOFTWARE REVISION

NO AMPLIFIER (p. 70)

GAS TYPE 1

(p. 59)

GAS TYPE 6

(p. 61)

FLOW DAMPING

(p. 63)

NOMINAL DIAMETER

(p. 64)

PREVIOUS SYSTEM

CONDITION (p. 66)

SIMULATION

MEASURAND (p. 68)

SERIAL NUMBER

(p. 69)

HARDWARE REVISION

NO AMPLIFIER (p. 70)

NUMBER OF GAS COM-

PONENTS (p. 58)

% FRACTION 5

(p. 61)

POSITIVE ZERO

RETURN (p. 63)

PIPE TYPE

(p. 64)

ACTUAL SYSTEM

CONDITION (p. 66)

SIMULATION FAILSAFE

MODE (p. 68)

SENSOR TYPE

(p. 69)

DEVICE SOFTWARE

(p. 70)

▼▼▼▼▼▼▼

▼

GAS MIXTURE

(p. 70)

SYSTEM PARAMETER

(p. 63)

SENSOR DATA

(p. 64)

SUPERVISION

(p. 66)

SIMULAT. SYSTEM

(p. 68)

SENSOR VERSION

(p. 69)

AMPLIFIER VERSION

(p. 70)

2 Group MEASURING VALUES Device Functions Proline t-mass 65

8Endress+Hauser

2 Group MEASURING VALUES

Function description MEASURING VALUES

!Note!

The engineering unit of the measured variable shown here can be set in the SYSTEM UNITS group (see Page 9).

MASS FLOW In this function, the currently measured mass flow appears on the display.

Display:

5-digit floating-point number, including unit

(e.g. 150.00 kg/h; 330.70 lb/h; etc.)

CORRECTED VOLUME

FLOW

In this function, the currently measured corrected volume flow appears on the display.

The calculated corrected volume flow is derived from the measured mass flow and the

reference density of the gas (at reference temperature and pressure).

User Interface:

5-digit floating-point number, including unit

(e.g. 104.97 Nm3/h; 110.73 Sm3/h; etc.)

TEMPERATURE In this function, the currently measured gas ambient temperature appears on the display.

Display:

5-digit floating-point number, including unit and sign

(e.g. –23.4 °C; +160.0 °F; 295.4 K; etc.)

Device Functions Proline t-mass 65 3 Group SYSTEM UNITS

Endress+Hauser 9

3 Group SYSTEM UNITS

Function description SYSTEM UNITS

You can select the unit for the measured variable in this function group.

UNIT MASS FLOW Use this function to select the unit for displaying the mass flow (mass/time).

The unit you select here is also valid for:

• Current outputs

• Frequency output

• Switching points (limit value for mass flow)

• Low flow cut off

!Note!

The following units of time can be selected:

s = second, m = minute, h = hour, d = day

Options:

Metric:

gram →g/time unit

kilogram →kg/time unit

Metric ton →t/time unit

US:

ounce →oz/time unit

pound →lb/time unit

ton →ton/time unit

For arbitrary units (see function TEXT ARBITRARY MASS on Page 12)

_ _ _ _ →_ _ _ _/s: _ _ _ _/min; _ _ _ _/h; _ _ _ _/day

Factory setting:

kg/h or US lb/h (country dependent, → Page 71 ff.)

!Note!

If you defined a unit for mass in the SPECIAL UNIT function group (see Page 12) the unit

in question is shown here.

UNIT MASS Use this function to select the unit for displaying the mass.

The unit you select here is also valid for:

• Pulse value (e.g. kg/p)

Options:

Metric →g; kg; t

US →oz; lb; ton

For free selectable units →_ _ _ _

(see function TEXT ARBITRARY MASS on Page 12)

Factory setting:

kg or US lb (country dependent, → Page 71 ff.)

!Note!

If you defined a unit of mass in the SPECIAL UNIT function group (see Page 12) the unit

in question is shown here.

The unit for the totalizer is independent of your choice here, it is selected separately in

the TOTALIZER group (see Page 21).

3 Group SYSTEM UNITS Device Functions Proline t-mass 65

10 Endress+Hauser

UNIT CORRECTED VOL-

UME FLOW

Use this function to select the unit for displaying the corrected volume flow (corrected

volume/time).

The unit you select here is also valid for:

• Current outputs

• Frequency output

• Relay switch points (limit value for corrected volume flow, flow direction)

• Low flow cut off

!Note!

The following units of time can be selected:

s = second, m = minute, h = hour, d = day

Options:

Metric:

Normal liter →Nl/time unit

Normal cubic meter →Nm3/time unit

US:

Standard cubic meter →Sm3/time unit

Standard cubic foot →Scf/time unit

Factory setting:

Nm3/h or Sm3/h (country dependent, → Page 71 ff.)

UNIT CORRECTED

VOLUME

Use this function to select the unit for displaying the corrected volume.

The unit you select here is also valid for:

• Pulse value (e.g. Nm3/p)

Options:

Metric:

Nm3

US:

Sm3

Scf

Factory setting:

Nm3or Sm3(country dependent, → Page 71 ff.)

!Note!

The unit of the totalizers is independent of your choice here. The unit for each totalizer is

selected separately for the totalizer in question.

Function description SYSTEM UNITS

Andere Handbücher für Proline t-mass 65F

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser Fieldgate FXA520 Bedienungsanleitung

Endress+Hauser

Endress+Hauser EngyCal RS33 Technische Daten

Endress+Hauser

Endress+Hauser Proline Prowirl F 200 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 FOUNDATION Fieldbus Bedienungsanleitung

Endress+Hauser

Endress+Hauser Dosimag Bedienungsanleitung

Endress+Hauser

Endress+Hauser eco-graph Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline System CA80PH Technische Daten

Endress+Hauser

Endress+Hauser Levelflex FMP51 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Prosonic Flow P 500 Bedienungsanleitung

Endress+Hauser

Endress+Hauser SpectraSensors OXY5500 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline t-mass 65F Handbuch

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag H 300 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Prosonic Flow E 100 HART Bedienungsanleitung

Endress+Hauser

Endress+Hauser Memograph M RSG40 Handbuch

Endress+Hauser

Endress+Hauser Liquiline System CA80AL Technische Daten

Endress+Hauser

Endress+Hauser Proline Promass series Technische Daten

Endress+Hauser

Endress+Hauser Waterpilot FMX21 Montageanleitung

Endress+Hauser

Endress+Hauser Promag 800 L Bedienungsanleitung

Endress+Hauser

Endress+Hauser Gammapilot M FMG50 Technische Daten

Endress+Hauser

Endress+Hauser FQG60 Handbuch

Endress+Hauser

Endress+Hauser memo-graph RSG10 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Technische Daten

Endress+Hauser

Endress+Hauser Topclean S CPC30 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung

Uniks

Uniks C126 Bedienungsanleitung