EnGenius ECB3500 Bedienungsanleitung

Quick Start Guide

11b/g Wireless Long Range Multi-function 7+1 AP

Quick Start Guide v.1.0

Refer to User’s Manual for complete instructions 1

ECB3500 is a powerful, enhanced, enterprise level product that supports 7 multi-functions to operate for

every kind of working environment.

This is a Wireless high transmit output power and high data rate indoor

device which plays different roles of Access Point/ Client Bridge /

Repeater / WDS AP / WDS Bridge / Client Router / AP Router. It

operates seamlessly in the 2.4 GHz frequency spectrum supporting the

802.11b (2.4GHz, 11Mbps) and super high speed of 802.11g (2.4GHz,

108Mbps) wireless standards. It supports high output power level

settings, bandwidth selection, RSSI indicator and antenna diversity

which enable the best transmitting and receiving signal for traffic

communication.

The attractive design, high performance, and array of features make ECB3500 a suitable wireless

solution for your residence or office.

This Guide will assist you in setting up the device as quickly as possible and with the least effort.

Hardware Installation

1. Place the unit in an appropriate place after

conducting a site survey.

2. Plug one end of the Ethernet cable into the

RJ-45 port on the rear panel of the device and

another end into your PC/Notebook.

3. Insert the DC-inlet of the power adapter into

the port labeled “DC-IN” and the other end

into the power socket on the wall.

IP Address Configuration

The default IP address of the device is

192.168.1.1 (Access Point mode).In order to log

into this device, you must first configure the

TCP/IP settings of your PC/Notebook.

4. In the control panel, double click Network

Connections and then double click on the

connection of your Network Interface Card

(NIC). You will then see the following screen.

5. Select Internet Protocol (TCP/IP) and then

click on the Properties button. This will allow

you to configure the TCP/IP settings of your

PC/Notebook.

6. Select Use the following IP Address radio

button and then enter the IP address

(192.168.1.21) and subnet mask

(255.255.255.0). Ensure that the IP address

and subnet mask are on the same subnet as

the device.

7. Click on the OK button to close this window,

and once again to close LAN properties

window.

Logging In

1. To configure the device through the

web-browser, enter the IP address of the

Bridge (default: 192.168.1.1) into the

address bar of the web-browser and press

Enter.

2. After connecting to the IP address, the

web-browser will display the login page.

Specify admin as the default User Name and

Password, and then click on the Login

button.

Administration

1. Click on the Administration link under the

Management menu. This option allows you

to create a new password for the device. For

security it is highly recommended for security

reasons.

2. Name: Specify a user name into the first field.

3. Password: Specify a password into this field

and then re-type the password into the

Confirm Password field.

4. Click on the Apply button to save the

changes.

Quick Start Guide

Long Range Wireless Access Point / Client Bridge

Quick Start Guide v.1.0

Refer to User’s Manual for complete instructions 2

Switching Between Operating Modes

This device can operate in the following modes:

Access Point, Client Bridge, WDS Bridge,

Repeater, AP Router, and Client Router.

1. Click on the System Properties link under

the System navigation drop-down menu.

2. Device Name: Specify a name for the device.

This is not the SSID.

3. Country/Region: Select the country from the

drop-down list.

4. Operating Mode: Select an operating mode

from the list (Access Point, Client Bridge, or

Client Router) and then click on the Apply

button.

5. Refer to the User’s Manual for a detailed

description and configuration for each

Operating Mode.

IP and DHCP Settings

1. Click on the IP Settings link under the

System drop-down menu This page

allows you to configure the device with a

static IP address or a DHCP client.

2. IP Network Setting: Select Obtain an IP

address automatically (DHCP) radio

button if the Access Point is connected to a

DHCP server. Select Specify an IP

Address radio button if you would like the

device to use a static IP address. In this

case, you would be required to specify an

IP address, subnet mask, and default

gateway IP address.

3. IP Address: Specify an IP address

4. IP Subnet Mask: Specify the subnet mask

for the IP address

5. Default Gateway: Specify the IP address

of the default gateway.

6. Click on the Apply button to save the

changes.

Note: If you change the IP address here, you may

need to adjust your PC’s network settings to

access the network again.

Wireless Network & Security

1. Click on the Wireless Network link on the

Wireless drop-down menu. This page

allows you to configure the wireless mode,

channel, SSID, and security settings.

2. Wireless Mode: Depending on the type of

wireless clients that are connected to the

network, you may select B, G, B/G-mixed

or Super G mode.

3. Channel: Select a channel from the

drop-down list. The channels available are

based on the country’s regulation.

4. Current Profiles: You may configure up to

four different wireless profiles. Click on the

Edit button to modify the profile and place

a check in the Enable box to activate the

profile.

5. SSID: The SSID must be identical on all

points of the wireless network and cannot

exceed 32 characters.

6. VLAN ID: If you have enabled VLAN

tagging on your network, specify the VLAN

tag ID.

7. Suppressed SSID: Place a check in this

box if you would like to hide the SSID. By

enabling this feature, wireless clients will

not be able to scan this access point in a

site survey.

8. Station Separation: This is also known as

layer 2 isolation. Clients connected to this

Access Point will not be able to directly

communicate with each other.

9. Security Mode: By default, the security is

disabled. Refer to the next section to

configure the security features such as

WEP, WPA, WPA-PSK, WPA2,

WPA2-PSK and WPA-Mixed.

10. Refer to the User’s Manual for a detailed

description and configuration for each

security feature.

11. Click on the Apply button to save the

changes.

Andere Handbücher für ECB3500

Inhaltsverzeichnis

Andere EnGenius Drahtloser Zugangspunkt Handbücher

EnGenius

EnGenius ENH210EXT Bedienungsanleitung

EnGenius

EnGenius ENH220EXT Bedienungsanleitung

EnGenius

EnGenius ECB-3220 Bedienungsanleitung

EnGenius

EnGenius EOC5611P Bedienungsanleitung

EnGenius

EnGenius ENH500 Bedienungsanleitung

EnGenius

EnGenius EWS550AP Bedienungsanleitung

EnGenius

EnGenius ECB600 Bedienungsanleitung

EnGenius

EnGenius EWS860AP The Neutron Series Bedienungsanleitung

EnGenius

EnGenius EWS850AP Bedienungsanleitung

EnGenius

EnGenius EWS357AP v3/ECW220 v2 Bedienungsanleitung

EnGenius

EnGenius AC866 Bedienungsanleitung

EnGenius

EnGenius M8000 Bedienungsanleitung

EnGenius

EnGenius ENS500 Bedienungsanleitung

EnGenius

EnGenius ECB1200 Bedienungsanleitung

EnGenius

EnGenius EAP-3660 Bedienungsanleitung

EnGenius

EnGenius ENH200 Bedienungsanleitung

EnGenius

EnGenius ECB1221R Bedienungsanleitung

EnGenius

EnGenius ENS1750 Bedienungsanleitung

EnGenius

EnGenius ECB1200 Bedienungsanleitung

EnGenius

EnGenius EW310AP Bedienungsanleitung

EnGenius

EnGenius EAP900H Bedienungsanleitung

EnGenius

EnGenius EAP9550 Bedienungsanleitung

EnGenius

EnGenius Neutron EWS210AP Bedienungsanleitung

EnGenius

EnGenius ECM355AP Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung