Equinox Systems 2M Flight CasedDMX LED Flame Machine Bedienungsanleitung

User Manual

Equinox 2M Flight Cased

DMX LED Flame Machine

Order code: FLAM12

www.prolight.co.uk

Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

 •Neverletthepower-cablecomeintocontactwithothercables.Handlethepower-cable

 andallmainsvoltageconnectionswithparticularcaution!

 •Neverremovewarningorinformativelabelsfromtheequipment.

 •Donotopentheequipmentanddonotmodifytheequipment.

 •Donotconnectthisequipmenttoadimmer-pack.

 •Donotswitchtheequipmentonandoffinshortintervals,asthiswillreducethe

 system’slife.

 •Onlyusetheequipmentindoors.

 •Donotexposetoammablesources,liquidsorgases.

 •Alwaysdisconnectthepowerfromthemainswhenequipmentisnotinuseorbefore

 cleaning!Onlyhandlethepower-cablebytheplug.Neverpullouttheplugbypullingthe

 power-cable.

 •Makesurethattheavailablevoltageisbetween220V/240V.

 •Makesurethatthepower-cableisnevercrimpedordamaged.Checktheequipmentand

 thepower-cableperiodically.

 •Iftheequipmentisdroppedordamaged,disconnectthemainspowersupplyimmediately.

 Haveaqualiedengineerinspecttheequipmentbeforeoperatingagain.

 •Iftheequipmenthasbeenexposedtodrastictemperatureuctuation(e.g.after

 transportation),donotswitchitonimmediately.Thearisingcondensationmightdamage

 theequipment.Leavetheequipmentswitchedoffuntilithasreachedroomtemperature.

 •Ifyourproductfailstofunctioncorrectly,discontinueuseimmediately.Packtheunit

 securely(preferablyintheoriginalpackingmaterial),andreturnittoyourProlightdealer

 forservice.

 •Onlyusefusesofsametypeandrating.

 •Repairs,servicingandpowerconnectionmustonlybecarriedoutbyaqualied

 technician.THISUNITCONTAINSNOUSERSERVICEABLEPARTS.

 •WARRANTY;Oneyearfromdateofpurchase.

OPERATING DETERMINATIONS

Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,

theproductmaysufferdamageandthewarrantybecomesvoid.

Incorrectoperationmayleadtodangere.g.:short-circuit,burns,electricshocks,LEDfailureetc.

Donotendangeryourownsafetyandthesafetyofothers!

Incorrectinstallationorusecancauseseriousdamagetopeopleandproperty.

Overview

You should nd inside the Equinox carton the following items:

1,Equinox2MFlightCasedDMXLEDFlameMachine2,Usermanual 3,Powercable

Features:

•Red/amberLEDSfortrueameeffect

•18x1WRGBALEDs(R:3,G:6,B:6,A:3)

•0-100%dimmingandvariablestrobe(onlyinstandalone)

•DMXchannels:4

•Staticcolourmixing,colourchange,colourfade,soundactive,DMXandmaster/slavemodes

•4pushbuttonmenuwithLEDdisplay

•IECpowerinsocket

•3-pinXLRin/outsockets

•Highvelocityfan(notsuitableforlownoiseapplications)

•Suppliedinfullightcase

•Heavyduty,industrialgradehandlesandbutterycatchesarerivetedforstrength.

•Maxameheight:2m

•Powerconsumption:157W

•Powersupply240V

•Dimensions:561x460x438mm

•Weight:20Kgs

Over View

Identication

1.LEDdisplay

2.DMXinputsocket

3.DMXoutputsocket

4.Sensitivitycontrol

5.IECpowerinputsocket

6.Modebutton

7.Enterbutton

8.Upbutton

9.Downbutton

10.Microphone

11.On/offpowerswitch

YT-9054FH

Operation:

Toactivatetheunit,rstconnecttheIECcableintotheunitandthenconnecttheplugintoaAC240V

powersupply.Oncetheunithasbeenconnectedusethe“POWER SWITCH”locatednexttothe

“POWER IEC” inputsockettoturntheunitON or OFF.

Operating Instructions

The2MFlightCasedDMXLEDFlameMachineisaDMX-512controllable,fullRGBAcolourmixing

FlameMachinemadeupofhighefciencyLED’s.Therearefourcolourgroups(red,blue,greenand

amber)whoseintensitycanbecontrolledindividuallyallowingthecreationofarangeofcolours.

The2MFlightCasedDMXLEDFlameMachinewilloperateinstand-alone,master/slave,sound

activatedandDMX-512control.

Operation modes

Static colour mode

Toaccessthestaticcolourmode,pressthe“MODE”buttontoshow“C000”ontheLEDdisplay.Now

pressthe“ENTER”buttontochoose“Cr”(red+amber),“C9”(green)or“Cb”(blue).Toadjustthe

brightnessusethe“UP” or “DOWN”buttonstoincreaseordecreasethesettingfrom00-99.

Examples:IfyousetCr,C9andCbtozero,theLEDamemachinewillhavenoLEDson(blackout).

IfyousetCrto99andC9andCbtozero,theLEDamemachinewillbe100%RedandAmber.

Toaddstrobe,pressthe“ENTER” buttonandusethe“UP” or “DOWN”buttonstoincreaseor

decreasethestrobespeedfrom00-99.

Note: 00 = Off, 99 = Full on

Colour change mode

Toaccessthecolourchangemode,pressthe“MODE”buttontoshow“J000”ontheLEDdisplay.Now

pressthe“ENTER” buttonandusethe“UP” or “DOWN”buttonstoincreaseordecreasethespeed

from00-99.

Note: 00 = Slow, 99 = Fast

Colour fade mode

Toaccessthecolourfademode,pressthe“MODE”buttontoshow“F000”ontheLEDdisplay.Now

pressthe“ENTER”buttonandusethe“UP” or “DOWN”buttonstoincreaseordecreasethespeed

from00-99.

Note: 00 = Slow, 99 = Fast

Sound active mode

Toaccessthesoundactivemode,pressthe“MODE”buttontoshow“Sund”ontheLEDdisplay.Now

usethe“SENSITIVITY” controlontherearpaneltoadjustthesoundsensitivitylevel.

Master/slave mode

Tosettheunitasthemaster,simplyuseanyoneoftheabovemodes.

Tosettheunitasaslave,pressthe“MODE”buttontoshow“Slau”ontheLEDdisplay.Nowtheslave

unitwillfollowinsequencewiththemasterunit.

Operation

DMX mode

ToaccesstheDMXmode,pressthe“MODE”buttontoshow“Addr”ontheLEDdisplay.Nowpressthe

“ENTER”buttonandusethe“UP” or “DOWN”buttonstosetthedesiredDXMaddressfrom000-512.

FortheDMXfunctions,pleaseseetheDMXchartbelow.

Operation

Channel

Value

000-125

000

126-255

001-255

Function

Nofunction

Red+Amber@100%

Green@100%

Blue@100%

Colourchase

Daisy Chain Connection

1)Connectthe(male)3pinconnectorsideoftheDMXcabletotheoutput(female)3pin

connectoroftherstxture

2)Connecttheendofthecablecomingfromtherstxturewhichwillhavea(female)3pin

connectortotheinputconnectorofthenextxtureconsistingofa(male)3pinconnector.

Proceedtoconnectfromtheoutputasstatedabovetotheinputofthefollowingxture

andsoon.

DMX Control Mode

OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomesto

customisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthexture

andeachxtureindependently.The2MFlightCasedDMXLEDFlameMachineuses4channelsof

control.

Setting the DMX address

TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”

from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel

indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas

addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105and

106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthechain

startsat107.

DMX-512:

•DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent

xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.

DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”XLR

terminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).

DMX Linking:

•DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogetherand

operatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.Toensure

properDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortestcablepath

possible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencetheDMX

addressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywhereinaDMX

line,atthebeginning,attheend,oranywhereinthemiddle.WhenaxtureisassignedaDMXaddress

of1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,nomatterwhereitis

locatedintheDMXchain.

DATA Cable (DMX cable) requirements (for DMX operation):

•The2MFlightCasedDMXLEDFlameMachinecanbecontrolledviaDMX-512protocol.TheDMX

addressissetonthebackoftheunit.YourunitandyourDMXcontrollerrequireastandard3-pinXLR

connectorfordatainput/output(gure1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

DMXSetUp

Notice:

•Besuretofollowgures2&3whenmakingyourowncables.Donotconnectthecable’sshield

conductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLR’soutercasing.

Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.

Special Note: Line termination:

•Whenlongerrunsofcableareused,youmayneedtouseaterminatoronthelastunitto

avoiderraticbehaviour.

Using a cable terminator (part number CABL90 3-pin or CABL89 5-pin) will decrease the

possibilities of erratic behaviour.

5-Pin XLR DMX Connectors:

•Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-Pin

XLRxturesmaybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pin

XLRconnectorsintoa3-pinlineacableadaptormustbeused.Thechartbelowdetailsthe

correctcableconversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems CARBON Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED019 Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion 50 MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems Colour Raider Uplighter Pack Bedienungsanleitung

Equinox Systems

Equinox Systems Hallucination Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion 200 Zoom Spot Bedienungsanleitung

Equinox Systems

Equinox Systems BLITZER Bedienungsanleitung

Equinox Systems

Equinox Systems Crossfire XP Bedienungsanleitung

Equinox Systems

Equinox Systems FXbar18 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED003 Bedienungsanleitung

Equinox Systems

Equinox Systems Hot Rod EQLED089 Bedienungsanleitung

Equinox Systems

Equinox Systems MoonPar Bedienungsanleitung

Equinox Systems

Equinox Systems Butterfly Quad Bedienungsanleitung

Equinox Systems

Equinox Systems Quad Pix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED136 Bedienungsanleitung

Equinox Systems

Equinox Systems MicroPar UV EQLED028 Bedienungsanleitung

Equinox Systems

Equinox Systems Flame Machine 1.5M Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Wash RGBA Bedienungsanleitung

Equinox Systems

Equinox Systems FEVER Bedienungsanleitung

Equinox Systems

Equinox Systems Kaleido XP Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten EQLED055 Bedienungsanleitung

Equinox Systems

Equinox Systems Triton Beam EQLED071 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED054 Bedienungsanleitung

Equinox Systems

Equinox Systems Confetti Burst EQLED400 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung