Equinox Systems Fusion 200 Zoom Spot Bedienungsanleitung

Order code: EQLED054

Fusion 200 Zoom Spot

User Manual

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 100~240V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• Never touch the xture during operation as it may be hot.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is not

designed for or suitable for household use. The product

must be installed by a qualied technician in accordance

with local territory regulations. The safety of the installation

is the responsibility of the installer. The xture presents

risks of severe injury or death due to re hazards, electric

shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 3

Safety advice

This xture falls under Protection Class 1, therefore it has to be connected

to a mains socket with a protective earthing connection.

Risk group 2, RG-2: CAUTION!

Do not stare at exposed LED in operation as it may damage/be harmful to

the eyes. Avoid looking directly into the light source.

CAUTION!

If the lens gets damaged ie. cracks or deep scratches so the output is impaired

then it must be replaced.

CAUTION!

The maximum ambient temperature (Ta) of 40° must not be exceeded.

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 4

0m 2m 3m 4m 5m

11° - Lux

25° - Lux

27900

9855

111600

39420

12400

4380

25°

6975

2463

4464

1576

11°

Product overview & technical specications

• 1 x 200W white LED (7500K)

• Adjustable beam angle: 11°-25°

• 11° - 27,900 Lux @ 2m,

25° - 9,855 Lux @ 2m

• 4.3kHz refresh rate

• Motorised zoom and focus

• 6 facet circular rotating indexable prism

plus 5 facet linear rotating indexable prism

• Gobo wheel 1: 7 rotating, indexable,

replaceable gobos + open

• Gobo wheel 2: 7 static gobos + open

• Colour wheel: 7 colours + open

• DMX channels: 2/14 or 18 selectable

• Auto, sound active manual control

and master/slave modes

• Pan/tilt auto correction

• 16-Bit pan/tilt positioning

• Pan: 540°, Tilt: 270°

• 0-100% dimming and variable strobe

• Quick release omega clamps included

• 4 push button menu with 2.6” LCD display

• PowerCON input/output

• 3-Pin XLR input/output

• Fan cooled

Fusion 200 Zoom Spot

Specications Fusion 200 Zoom Spot

Power consumption 240W

Power supply 100~240V, 50/60Hz

Fuse F4A 250V

Dimensions 450 x 302 x 200mm

Weight 12.7kg

Order code EQLED054

The Fusion 200 Spot features a single 200W LED and produces stunning light shows with an adjustable beam

angle of 11°- 25°. Offering 7 colours plus open along with a rotating and static gobo wheel each containing

7 gobos plus open, the xture is ideal for installation and performers alike. Two bi-directional indexable prisms

(6 facet circular and 5 facet linear) further bolster the xtures comprehensive features and a motorised zoom

keeps the gobos razor sharp over any distance. PowerCON, DMX in/out and a four button LCD display further

enhance the xture.

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 5

Technical specications

355mm

450mm

274mm

405mm

293mm

302mm

96mm

183mm

200mm

96mm

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 6

Technical specications

01 - LCD display

02 - Function buttons

03 - 3-Pin DMX input

04 - 3-Pin DMX output

05 - PowerCON input

06 - PowerCON output

07 - Fuse F4A 250V

08 - Power switch

09 - Carry handles

In the box: 1 x xture,

2 x omega clamps,

1 x power cable

& 1 x user manual

09 07

01 02 04 08 05 0603

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 7

Installation

Before installing the xture, the supporting structure (ie. truss) must be able to hold a minimum of 10

times the xtures weight without any deformation (eg. 15kg - 150kg point load). The xture must be

secured with a secondary safety attachment when being installed (ie. an appropriate safety cable).

Never stand directly below the xture when mounting, removing, and/or servicing.

Overhead installation requires experience and qualications to calculate working load limits, the

material being used at the installation area and periodic safety inspections of the xture and installation

material. If you do not have the relevant experience and/or qualications please do not attempt the

installation yourself. The installation should be checked annually by a qualied person.

The Equinox Fusion 200 Zoom Spot can be operated in a number of mounting positions as shown

in the diagram above, hanging upside-down from the ceiling or truss, mounting sideways on truss or

stood upright on a at level surface. Always use a safety wire as an extra safety precaution to prevent

damage/injury in the event a clamp fails (see the next page for clamp installation).

Never use the carry handles for secondary attachments.

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 8

Installation

Installation:

1. Fasten each clamp to the omega clamps with a bolt and lock nut through the hole in the

omega clamp.

2. Align and insert the omega clamp quick-lock fasteners with the respective holes on the bottom

of the unit.

3. Tighten both locking fasteners clockwise on each omega clamp ensuring they’re fully secure.

4. Mount the xture onto your truss system via the clamps and tighten to ensure secure.

5. Pull the safety cable through the safety cable holes located on the metal base plate on the

underside of the xture and around the truss.

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 9

Operating instructions

Control Panel Menu:

The LCD control panel situated on the front of the xture allows the user to access the menu system to

adjust the xtures settings.

When the unit has been powered on the display will show “Equinox Fusion 200 Zoom Spot”,

“Motor Reset... Please Wait...” whilst the unit performs its motor reset.

The xture will then return to its home screen.

Pressing the “ENTER” button once will take the user to the xtures main menu. Using the “UP” and

“DOWN” buttons you can then navigate between the different options in the main menu. Pressing the

“ENTER” button on one of these options allows you to access the sub menu where you can use the

“UP” and “DOWN” buttons to select option/value required. Once the option/value has been selected

press the “ENTER” button once more to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

DOWN

ENTERMENU

DMX

200 ZOOM SPOT

www.prolight.co.uk Fusion 200 Zoom Spot User Manual 10

1. DMX

Address

1. DMX Address

xxx

DMX address:

To access the DMX address mode, press the

“ENTER” button and use the “UP” and “DOWN”

buttons to show “DMX Address” on the LCD

display. Now press the “ENTER” button and use

the “UP” and “DOWN” buttons to set the required

DMX address. Press the “ENTER” button to

conrm the setting.

Main Menu - Defaults are in grey

DMX channel mode:

To access the DMX channel mode, press the

“ENTER” button and use the “UP” and “DOWN”

buttons to show “Channel Mode” on the LCD

display. Now press the “ENTER” button and use

the “UP” and “DOWN” buttons to set the required

DMX channel. Press the “ENTER” button to

conrm the setting.

Show mode:

To access the show modes, press the “ENTER”

button and use the “UP” and “DOWN” buttons

to show “Show Mode” on the LCD display. Now

press the “ENTER” button and use the “UP” and

“DOWN” buttons to set the required show mode.

Press the “ENTER” button to conrm the setting.

Show 4 is a forward facing show mode.

2. Channel

Mode 2 Channel

14 Channel

18 Channel

3. Show

Mode Show 1

Show 2

Show 3

Show 4

Operating instructions

Default

001

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems Hot Rod EQLED089 Bedienungsanleitung

Equinox Systems

Equinox Systems Confetti Burst EQLED400 Bedienungsanleitung

Equinox Systems

Equinox Systems Midas Spot Bedienungsanleitung

Equinox Systems

Equinox Systems Cabaret Colour HEX Bedienungsanleitung

Equinox Systems

Equinox Systems MoonPar Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED135 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED064 Bedienungsanleitung

Equinox Systems

Equinox Systems Helix 100W Gobo Flower Bedienungsanleitung

Equinox Systems

Equinox Systems BLITZER Bedienungsanleitung

Equinox Systems

Equinox Systems Pulse Tube Bedienungsanleitung

Equinox Systems

Equinox Systems Domin8R II Bedienungsanleitung

Equinox Systems

Equinox Systems C-Shot Bedienungsanleitung

Equinox Systems

Equinox Systems Quad Pix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems TAURUS Bedienungsanleitung

Equinox Systems

Equinox Systems Six Shooter MKII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED136 Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED019 Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer RGB Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems Colour Raider Uplighter Pack Bedienungsanleitung

Equinox Systems

Equinox Systems Helix Scan XP 150W Scanner Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth LED Starcloth System Bedienungsanleitung

Equinox Systems

Equinox Systems HYPE Bedienungsanleitung

Equinox Systems

Equinox Systems Ultra LED Scan EQLED75 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung