Equinox Systems Goboceptor Bedienungsanleitung

Order code: EQLED066

Goboceptor

User Manual

www.prolight.co.uk Goboceptor User Manual

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.

• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.

• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary

fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.

• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand

thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.

Donotendangeryourownsafetyandthesafetyofothers!

Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Neverletthepowercablecomeintocontactwithother

cables.Handlethepowercableandallmainsvoltage

connectionswithparticularcaution!

• Neverremovewarningorinformativelabelsfromtheunit.

• Donotopentheequipmentanddonotmodifytheunit.

• Donotconnectthisequipmenttoadimmerpack.

• Donotswitchtheequipmentonandoffinshortintervals,

asthiswillreducethesystem’slife.

• Onlyusetheequipmentindoors.

• Donotexposetoammablesources,liquidsorgases.

• Alwaysdisconnectthepowerfromthemainswhen

equipmentisnotinuseorbeforecleaning!Onlyhandle

thepower-cablebytheplug.Neverpullouttheplugby

pullingthepower-cable.

• Makesurethattheavailablemainssupplyvoltageis

between100~240VAC,50/60Hz.

• Makesurethatthepowercableisnevercrimpedor

damaged.Checktheequipmentandthepowercable

periodically.

• Iftheequipmentisdroppedordamaged,disconnectthe

mainspowersupplyimmediatelyandhaveaqualied

engineerinspecttheequipmentbeforeoperatingagain.



• Iftheequipmenthasbeenexposedtodrastic

temperatureuctuation(e.g.aftertransportation),

donotconnectpowerorswitchitonimmediately.

Thearisingcondensationmightdamagetheequipment.

Leavetheequipmentswitchedoffuntilithasreached

roomtemperature.

• Ifyourproductfailstofunctioncorrectly,stopuse

immediately.Packtheunitsecurely(preferablyinthe

originalpackingmaterial),andreturnittoyourProLight

dealerforservice.

• Onlyusefusesofsametypeandrating.

• Repairs,servicingandpowerconnectionmustonlybe

carriedoutbyaqualiedtechnician.THISUNITCONTAINS

NOUSERSERVICEABLEPARTS.

• Thislightingxtureisforprofessionaluseonly-itis

notdesignedfororsuitableforhouseholduse.The

productmustbeinstalledbyaqualiedtechnicianin

accordancewithlocalterritoryregulations.Thesafetyof

theinstallationistheresponsibilityoftheinstaller.The

xturepresentsrisksofsevereinjuryordeathduetore

hazards,electricshockandfalls.

• Warning!RiskGroup2LEDproductaccordingto

EN62471.Donotviewthelightoutputwithoptical

instrumentsoranydevicethatmayconcentratethebeam.

• WARRANTY:Oneyearfromdateofpurchase.

www.prolight.co.uk Goboceptor User Manual

Product overview & technical specications

Threeeffectsinone.Thisroomllingderbyeffecthasbeencombinedwith

agobowheeltoproduceamultitudeofcolourchangingbeams.Adding

evenmoretothemixare8x3WUVoodsand2x3Wstrobesallina

compacthousing.

•8x3WLEDs(R:2,G:2,B:2,A:2)plus8x3WUVLEDs

and2x3WwhiteLEDswithstrobeandwasheffects

•DMXchannels:2or7selectable

•Auto,soundactiveandmaster/slavemodes

•0-100%dimmingandvariablestrobe

•Suppliedwithhangingbracket

•4pushbuttonmenuwithLEDdisplay

•IECpowerinput/output

•3-PinXLRinput/output

•Fancooled

•SuppliedwithIRremote

Goboceptor

Specications

Powerconsumption 60W

Powersupply 100~240V,50/60Hz

Fuse T2A250V

Dimensions 192x230x245mm

Weight 2kg

Ordercodes EQLED066

192mm

230mm 245mm

www.prolight.co.uk Goboceptor User Manual

Technical specications

09 08

07 05 06

01-LEDdisplay

02-Functionbuttons

03-3-PinDMXinput

04-3-PinDMXoutput

05-IECpowerinput

06-IECpoweroutput

07-FuseT2A250V

08-On/offswitch

09-Safetyeye

10-Hangingbracket

11-Hangingbracketadjustmentknobs

Inthebox:1 x xture,

1 x IR remote,

1 x power cable

& 1 x user manual

www.prolight.co.uk Goboceptor User Manual

Operating instructionsOperating instructions

5 1 2

A d d r

DMX address setting

2 C h

8 C h

C h n d

Channel modes

d N S t

No DMX signal

N A s t

b L N d

L A S t

N A s t

S L A v

S L N d

Master/slave mode

S h 1

S h 4

S h N d

Show modes

100

S P E E

Show mode speed

o n

oFF

S o U n

Sound active

o n

oFF

LEd

LED backlight

t E S t

Test mode

F h r S

Fixture hours

uEr

Software version

r S E t

Reset

1 0 0

S o S E

Sound sensitivity

d I S P

d S I P

d I S P

Display invert

www.prolight.co.uk Goboceptor User Manual

DMX mode:

OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes

tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitof

thextureandeachxtureindependently.

ToaccesstheDMXaddressmode,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonson

therearoftheunittoshowA001ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”

and“DOWN”buttonstosettherequiredDMXaddress.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

DMX channel mode:

ToaccesstheDMXchannelmode,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonson

therearoftheunittoshowChndontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”

and“DOWN”buttonstochooseoneofthe2or8DMXchannelmodes.Pressthe“ENTER”

buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Operating instructions

2 channel mode: 8 channel mode:

Channel Value Function

CH1

000-009 Nofunction

010-069 Show1(RGBALEDs)

070-129 Show2(WhiteLEDs)

130-189 Show3(UVLEDs)

190-255 Show4(Shows1-3random)

CH2 000-247 Show1-4speed(slow-fast)

248-255 Show1-4soundactive

Channel Value Function

CH1

000-009 Nofunction

010-069 Show1(RGBALEDs)

070-129 Show2(WhiteLEDs)

130-189 Show3(UVLEDs)

190-255 Show4(Shows1-3random)

CH2

000-009 RGBALEDsoff

010-198 Colourselection

199-225 Colourchangesinglecolour

(slow-fast)

226-255 Colourchange(slow-fast)

CH3

000-009 Nofunction

010-244 Strobe(RGBALEDsslow-fast)

245-255 Strobe(RGBALEDssoundcontrol)

CH4 000-127 Gobopositioning

128-255 Goboscanning(slow-fast)

CH5 000-255 WhiteLEDsdimmer(0-100%)

CH6 000-244 Strobe(WhiteLEDsslow-fast)

245-255 Strobe(WhiteLEDssoundcontrol)

CH7 000-255 UVLEDsdimmer(0-100%)

CH8 000-244 Strobe(UVLEDsslow-fast)

245-255 Strobe(UVLEDssoundcontrol)

www.prolight.co.uk Goboceptor User Manual

Operating instructions

Show mode:

Toaccesstheshowmodes,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonsontherear

oftheunittoshowShNdontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and

“DOWN”buttonstochoosebetweenSh 1~Sh 4.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Show mode speed:

Toadjusttheshowmodespeed,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonson

therearoftheunittoshowSPEEontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”

and“DOWN”buttonstochoosebetween0~100.Pressthe“ENTER”buttontoconrmthesetting.

Value: 0 - 100 (0 = slow, 100 = fast)

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Master/slave mode:

Tosetthemasterunit,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonsontherear

oftheunittoshowSLNd ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and

“DOWN”buttonstochooseNast.Pressthe“ENTER”buttontoconrmthesetting.Thenselectyour

desiredprogram.

Tosettheotherunitsinslavemode,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttons

ontherearoftheunittoshowSLNdontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe

“UP”and“DOWN”buttonstochooseSLAv.Pressthe“ENTER”buttontoconrmthesetting.Theunit

willnowruninsequencewiththemasterunit.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.

Sound active:

Toaccesssoundactivesetting,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonsonthe

rearoftheunittoshowSoUnontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”

and“DOWN”buttonstochoosebetweenonoroff.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Sound sensitivity:

Toadjustthesoundsensitivity,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonsonthe

rearoftheunittoshowSoSEontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”

and“DOWN”buttonstochoosebetween0~100.Pressthe“ENTER”buttontoconrmthesetting.

Value: 0 - 100 (0 = low, 100 = high)

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

www.prolight.co.uk Goboceptor User Manual

DMX signal lost:

TochangewhattheunitdoeswhentheDMXsignalislost,pressthe“MENU”buttonandusethe“UP”

and“DOWN”buttonsontherearoftheunittoshowdNstontheLEDdisplay.Nowpressthe“ENTER”

buttonandusethe“UP”and“DOWN”buttonstochoosebetweenNAst(Master/slavemode),LASt

(Holdthelastcommand)orbLNd(Blackout).Pressthe“ENTER”buttontoconrmthesetting.Toexit

outofanyoftheaboveoptions,pressthe“MENU”button.

LED backlight:

ToaccesstheLEDbacklightsetting,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonson

therearoftheunittoshowLEdontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”

and“DOWN”buttonstochoosebetweenonorofF.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Test mode:

Toaccessthetestmode,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonsontherearof

theunittoshowtEStontheLEDdisplay.Nowpressthe“ENTER”buttonandthetestmodewillrun.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Display invert setting:

Toaccessthedisplayinvertsetting,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonson

therearoftheunittoshowdISPontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”

and“DOWN”buttonstochoosebetweendISPordSIp.Pressthe“ENTER”buttontoconrmthe

setting.Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Fixture hours:

Toaccessthexturehours,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonsontherear

oftheunittoshowFhrSontheLEDdisplay.Nowpressthe“ENTER”buttonandthexturehourswill

bedisplayed.Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Software version:

Toaccessthesoftwareversion,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonson

therearoftheunittoshowvErontheLEDdisplay.Nowpressthe“ENTER”buttonandthesoftware

versionwillbedisplayed.Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Reset:

Toaccesstheresetsetting,pressthe“MENU”buttonandusethe“UP”and“DOWN”buttonsontherear

oftheunittoshowrSEtontheLEDdisplay.Nowpressthe“ENTER”buttonandtheunitwillstartto

reset.Pleasenote:theLEDdisplaywillgooffduringthistimeandwillcomebackonafter15seconds

oncetheresethasbeenperformed.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Operating instructions

www.prolight.co.uk Goboceptor User Manual

Operating instructions

IR remote functions:

Button functions:

01-Setstheunitintoblackoutonoroff

02-Setstheunitintothechosenshowmode-Usethe

‘Speed’,‘Speed-’and‘Speed+’buttonstoselect

thedesiredspeed.

03-Allowsacolourtobeselected

04-Selectsarandomcolour

05-Putstheunitintosoundactivemodeon

06-Putstheunitintosoundactivemodeoff

07-Increasestheselectedshowspeed

08-Decreasestheselectedshowspeed

09-Setstheselectedshowspeedatamediumspeed

www.prolight.co.uk Goboceptor User Manual

Setting the DMX address:

TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”

from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel

indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas

addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105

and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe

chainstartsat107.

DMX 512:

DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent

xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.

DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”

XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).

DMX linking:

DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether

andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.

ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest

cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe

DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein

aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda

DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,

nomatterwhereitislocatedintheDMXchain.

DATA cable (DMX cable) requirements (for DMX operation):

ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.

YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,

seeimagebelow.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

FurtherDMXcablescanbe

purchasedfromallgoodsound

andlightingsuppliersor

ProLightConceptsdealers.

Pleasequote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

Inhaltsverzeichnis

Andere Equinox Systems Beleuchtungsausrüstung Handbücher

Equinox Systems

Equinox Systems LED Par 64 Bedienungsanleitung

Equinox Systems

Equinox Systems ATRIA Bedienungsanleitung

Equinox Systems

Equinox Systems NEBULA Bedienungsanleitung

Equinox Systems

Equinox Systems VS 1500 Fogger Bedienungsanleitung

Equinox Systems

Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung

Equinox Systems

Equinox Systems XP 80W Bedienungsanleitung

Equinox Systems

Equinox Systems VIXEN EQLA36 Bedienungsanleitung

Equinox Systems

Equinox Systems Swing Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Vortex Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Lithium Batten Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED65 Giga Bar System Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Tri Bedienungsanleitung

Equinox Systems

Equinox Systems SCORPIO EQLA11 Bedienungsanleitung

Equinox Systems

Equinox Systems VEGA EQLA16 Bedienungsanleitung

Equinox Systems

Equinox Systems Megabar System EQLED63 Bedienungsanleitung

Equinox Systems

Equinox Systems ORION Bedienungsanleitung

Equinox Systems

Equinox Systems SIGMA EQLA09 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par Series Bedienungsanleitung

Equinox Systems

Equinox Systems Explo Strobe EX-2500 Bedienungsanleitung

Equinox Systems

Equinox Systems FLAM11 Bedienungsanleitung

Equinox Systems

Equinox Systems COBALT Bedienungsanleitung

Equinox Systems

Equinox Systems ARIES EQLA20 Bedienungsanleitung

Equinox Systems

Equinox Systems Cirrus Bedienungsanleitung

Equinox Systems

Equinox Systems Terminator 2 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung