Equinox Systems FLAM11 Bedienungsanleitung

Order code: FLAM11

1.5m DMX

Flame Machine

User Manual

www.prolight.co.uk 1.5m DMX Flame Machine User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

240V AC, 50Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is

not designed for or suitable for household use. The

product must be installed by a qualied technician in

accordance with local territory regulations. The safety of

the installation is the responsibility of the installer. The

xture presents risks of severe injury or death due to re

hazards, electric shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk 1.5m DMX Flame Machine User Manual 3

Product overview & technical specications

This 1.5m LED DMX ame machine featuresred, green and blue 10mm LEDs,

so you can choose any colour of ame.

Ideal for incorporation with other mood

enhancing lighting. Ideal for weddings,

halloween and special events.

• 168 x 10mm LEDs (R: 60, G: 54, B: 54)

• DMX channels: 6

• Sound active, auto and master/slave modes

• Built-in colour change programs

• High velocity fans (not suitable for

low noise applications)

• IEC power input

• 3-Pin XLR input/output

1.5m Flame Machine

Specications

Power consumption 150W

Power supply 110-240V, 50/60Hz

Fuse F2A 250V

Dimensions 512 x 240 x 330mm

Weight 9.7kg

Order codes FLAM11

330mm

512mm 240mm

01 - Handle

02 - On/off switch

03 - IEC power input

04 - Fuse: F2A 250V

05 - Earth point

06 - 3-Pin DMX input

07 - 3-Pin DMX output

08 - Dipswitches

09 - Sensitivity/brightness adjustment knob

In the box: 1 x xture,

1 x power cable

& 1 x user manual

www.prolight.co.uk

FUSE: F2A 250V

POWER INPUT: 240V~50Hz

DMX INPUT

DIPSWITCHES

SENSITIVITY

110

DMX OUTPUT

OFF

www.prolight.co.uk 1.5m DMX Flame Machine User Manual 4

Operating instructions

Operation:

Located on the side panel of the unit is IEC power input socket. Connect the IEC cable to the unit and

connect to a 110-240V power supply. Select the power input switch to the “ON” position.

To turn the unit off switch from the “ON” position to the “OFF” position.

DMX mode:

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of the

xture and each xture independently.

To access the DMX address mode, set dipswitch 10 to the “ON” position and use dipswitches 1-9 to

address each xture accordingly.

Strobe mode:

To access the strobe mode, set dipswitch 1 to the “ON” position and all the others to the “OFF”

position. Now use the sensitivity control to adjust the speed.

Fade mode:

To access the fade mode, set dipswitch 2 to the “ON” position and all the others to the “OFF”

position. Now use the sensitivity control to adjust the speed.

Colour change mode:

To access the 7 colour change mode, set dipswitch 3 to the “ON” position and all the others to the “OFF”

position. To access the 5 colour change mode, set dipswitch 4 to the “ON” position and all the others to

the “OFF” position. To access the red & green colour change mode, set dipswitch 5 to the “ON” position

and all the others to the “OFF” position. Now use the sensitivity control to adjust the speed.

Static colour mode:

To set a static colour use the following dipswitches:

Set dipswitch 6 to the “ON” position for Red, set dipswitch 7 to the “ON” position for Green and set

dipswitch 8 to the “ON” position for Blue. Now use the sensitivity control to adjust the brightness.

Please note: Dipswitches 6, 7 & 8 can be combined to mix colours.

Sound mode:

To access the sound mode, set dipswitch 9 to the “ON” position and all the others to the “OFF” position.

Now use the sensitivity control to adjust the sound sensitivity.

6 channel mode:

Channel Value Function

CH1 000-127 No function

128-255 DMX mode

CH2 000-255 Red (0-100%)

CH3 000-255 Green (0-100%)

CH4 000-255 Blue (0-100%)

CH5

000-010 No function

011-085 Strobe mode (slow-fast)

086-160 Auto mode (slow-fast)

161-235 Fade mode (slow-fast)

236-255 Sound mode

CH6 000-255 Strobe speed (slow-fast)

(CH2, 3 & 4)

www.prolight.co.uk 1.5m DMX Flame Machine User Manual 5

Master/slave mode:

Use any of the above modes to set the master unit. To set the unit(s) in slave mode set dipswitch 10

to the “ON” position and all the others to the “OFF” position.

Please note: When all dipswitches are set to the “OFF” position the unit will run an RGB colour chase.

Use the sensitivity control to adjust the sound sensitivity.

DMX dipswitch quick reference chart

Operating instructions

DMX DIPSWITCH SET

0 = OFF

1 = ON

#90000000011111111

#80000111100001111

#70011001100110011

#60101010101010101

#1 #2 #3 #4 #5

00000 3264 96 128 160 192 224 256 288 320 352 384 416 448 480

1 0 0 0 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481

0 1 0 0 0 2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482

1 1 0 0 0 3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483

0 0 1 0 0 4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484

10100 537 69 101 133 165 197 229 261 293 325 357 389 421 453 485

0 1 1 0 0 6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486

1 1 1 0 0 7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487

0 0 0 1 0 8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488

10010 941 73 105 137 169 201 233 265 297 329 361 393 425 457 489

01010 10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490

11010 11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491

00110 1244 76 108 140 172 204 236 268 300 332 364 396 428 460 492

10110 13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493

01110 14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494

11110 15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495

00001 16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496

10001 17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497

01001 18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498

11001 19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499

0 0 1 0 1 20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500

10101 21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501

0 1 1 0 1 22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502

1 1 1 0 1 23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503

00011 24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504

10011 2557 89 121 153 185 217 249 281 313 345 377 409 441 473 505

0 1 0 1 1 26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506

11011 27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507

0 0 1 1 1 28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508

10111 2961 93 125 157 189 221 253 285 317 349 381 413 445 477 509

0 1 1 1 1 30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510

11111 31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511

www.prolight.co.uk 1.5m DMX Flame Machine User Manual 6

Setting the DMX address:

The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”

from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel

indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was

addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105

and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the

chain starts at 107.

DMX 512:

DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.

DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”

XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).

DMX linking:

DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest

cable path possible. The order in which xtures are connected in a DMX line does not inuence the

DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in

a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a

DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,

no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):

This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.

Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output,

see image below.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

Further DMX cables can be

purchased from all good sound

and lighting suppliers or

Pro Light Concepts dealers.

Please quote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk 1.5m DMX Flame Machine User Manual 7

Notice:

Be sure to follow the diagrams below when making your own cables. Do not connect the cables

shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs

outer casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special note:

Line termination:

When longer runs of cable are used,

you may need to use a terminator on

the last unit to avoid erratic behaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a

3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.

Termination reduces signal transmission

problems and interference. It is always

advisable to connect a DMX terminal,

(resistance 120 Ohm 1/4 W) between pin 2

(DMX-) and pin 3 (DMX+) of the last xture.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

www.prolight.co.uk 1.5m DMX Flame Machine User Manual 8

WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed of

with other household wastes at the end of its working life. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, please separate this from other

types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their

local government ofce, for details of where and how they can take this item for environmentally

safe recycling.

Business users should contact their supplier and check the terms and conditions of the

purchase contract. This product should not be mixed with other commercial wastes for disposal.

Inhaltsverzeichnis

Andere Equinox Systems Beleuchtungsausrüstung Handbücher

Equinox Systems

Equinox Systems EQLED040 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Flower EQLED77 Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Saber Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED203 Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Orbit MKII Bedienungsanleitung

Equinox Systems

Equinox Systems 400W UV Cannon Bedienungsanleitung

Equinox Systems

Equinox Systems MidiPar Tri Plus Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED032A Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Lithium Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Megabar System EQLED63 Bedienungsanleitung

Equinox Systems

Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung

Equinox Systems

Equinox Systems QUADZILLA Bedienungsanleitung

Equinox Systems

Equinox Systems KAMIKAZE EQLA14 Bedienungsanleitung

Equinox Systems

Equinox Systems Nimbus Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par Series Bedienungsanleitung

Equinox Systems

Equinox Systems Krypton EQLED21 Bedienungsanleitung

Equinox Systems

Equinox Systems Goboceptor Bedienungsanleitung

Equinox Systems

Equinox Systems XP 80W Bedienungsanleitung

Equinox Systems

Equinox Systems GEMINI Bedienungsanleitung

Equinox Systems

Equinox Systems Eyebar Bedienungsanleitung

Equinox Systems

Equinox Systems TRICLOPS EQLED50 Bedienungsanleitung

Equinox Systems

Equinox Systems SCORPIO EQLA11 Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT MAX MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Axis 50W Gobo Flower Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung