Equinox Systems Power Par Series Bedienungsanleitung

Order codes:

Power Par 36 - EQLED112

Power Par 54 - EQLED113

Power Par Series

User Manual

www.prolight.co.uk Power Par Series User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.

• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.

• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary

fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.

• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand

thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.

Donotendangeryourownsafetyandthesafetyofothers!

Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Neverletthepowercablecomeintocontactwithother

cables.Handlethepowercableandallmainsvoltage

connectionswithparticularcaution!

• Neverremovewarningorinformativelabelsfromtheunit.

• Donotopentheequipmentanddonotmodifytheunit.

• Donotconnectthisequipmenttoadimmerpack.

• Donotswitchtheequipmentonandoffinshortintervals,

asthiswillreducethesystem’slife.

• Onlyusetheequipmentindoors.

• Donotexposetoammablesources,liquidsorgases.

• Alwaysdisconnectthepowerfromthemainswhen

equipmentisnotinuseorbeforecleaning!Onlyhandle

thepower-cablebytheplug.Neverpullouttheplugby

pullingthepower-cable.

• Makesurethattheavailablemainssupplyvoltageis

between100~240VAC,50/60Hz.

• Makesurethatthepowercableisnevercrimpedor

damaged.Checktheequipmentandthepowercable

periodically.

• Iftheequipmentisdroppedordamaged,disconnectthe

mainspowersupplyimmediatelyandhaveaqualied

engineerinspecttheequipmentbeforeoperatingagain.



• Iftheequipmenthasbeenexposedtodrastic

temperatureuctuation(e.g.aftertransportation),

donotconnectpowerorswitchitonimmediately.

Thearisingcondensationmightdamagetheequipment.

Leavetheequipmentswitchedoffuntilithasreached

roomtemperature.

• Ifyourproductfailstofunctioncorrectly,stopuse

immediately.Packtheunitsecurely(preferablyinthe

originalpackingmaterial),andreturnittoyourProLight

dealerforservice.

• Onlyusefusesofsametypeandrating.

• Repairs,servicingandpowerconnectionmustonlybe

carriedoutbyaqualiedtechnician.THISUNITCONTAINS

NOUSERSERVICEABLEPARTS.

• Thislightingxtureisforprofessionaluseonly-itis

notdesignedfororsuitableforhouseholduse.The

productmustbeinstalledbyaqualiedtechnicianin

accordancewithlocalterritoryregulations.Thesafetyof

theinstallationistheresponsibilityoftheinstaller.The

xturepresentsrisksofsevereinjuryordeathduetore

hazards,electricshockandfalls.

• Warning!RiskGroup2LEDproductaccordingto

EN62471.Donotviewthelightoutputwithoptical

instrumentsoranydevicethatmayconcentratethebeam.

• WARRANTY:Oneyearfromdateofpurchase.

www.prolight.co.uk Power Par Series User Manual 3

Product overview & technical specications

Theseextremelypowerfulxturesfeature3Wtri-colourLEDsandproduceavariedrangeofeffectsincluding

colourchangeandfadeeffectscontrollableinautoandsoundactivemodesalongwithDMX.Adualbracketis

includedallowingthexturetobehungorstoodontheoor.

Power Par 36

Power Par 54

• 36x3Wtri-colourLEDs

(RGB)

• Beamangle:25°

• 1459Lux@2m(fullon)

• DMXchannels:6

selectable

• Auto,soundactiveand

master/slavemodes

• 0-100%dimmingand

variablestrobe

• 4pushbuttonmenu

withLEDdisplay

• Bracketallowsformultiple

riggingoroorstanding

applications

• IECpowerinput/output

• 3-PinXLRinput/output

• Fancooled

• 54x3Wtri-colourLEDs

(RGB)

• Beamangle:25°

• 2530Lux@2m(fullon)

• DMXchannels:6

selectable

• Auto,soundactiveand

master/slavemodes

• 0-100%dimmingand

variablestrobe

• 4pushbuttonmenu

withLEDdisplay

• Bracketallowsformultiple

riggingoroorstanding

applications

• IECpowerinput/output

• 3-PinXLRinput/output

• Fancooled

Power Par Series

Specications Power Par 36

Powerconsumption 110W

Powersupply 100~240V,50/60Hz

Fuse F3A250V

Dimensions 290x265x100mm

Weight 1.5kg

Ordercodes EQLED112

290mm

265mm 100mm

MENU DOWN

FUSE: F3A 250V

POWER INPUT/OUTPUT:

100~240V, 50/60Hz

DMX INPUT

DMX OUTPUT

UP ENTER

POWER PAR

www.prolight.co.uk

01-Hangingbracket

02-Hangingbracket

adjustmentknob

03-LEDdisplay

04-Functionbuttons

05-IECpowerinput

06-IECpoweroutput

07-Fuse:F3A250V

08-3-PinDMXinput

09-3-PinDMXoutput

10-Fan

Inthebox:

1 x xture,

1 x power cable

& 1 x user manual

Specications Power Par 54

Powerconsumption 165W

Powersupply 100~240V,50/60Hz

Fuse F3A250V

Dimensions 290x265x100mm

Weight 1.5kg

Ordercodes EQLED113

www.prolight.co.uk Power Par Series User Manual 4

Operating instructions

DMX mode:

OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes

tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthe

xtureandeachxtureindependently.

ToaccesstheDMXaddressmode,pressthe“MENU”buttononthefrontoftheunittoshowA001

ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe

requiredDMXaddress.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

RGB colour mix mode:

Inthismodeyoucansetthexturetoanycolourandanybrightness.

Toaccessthecolourmixmodepress“MENU”untilthedisplayshowsPr--ontheLEDdisplay.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectPr00.

Pressthe“ENTER”buttontoshow r---with3digitsafterontheLEDdisplay.

Pressthe“ENTER”buttontoconrm.

Therrepresentsred,G=greenandb=blue.

The3digitsafterarethebrightnesssettingfrom000~255.

For example:

Ifyousetr,G,balltozero,yourunitwillhavenoLEDslitup(blackout).

Ifyousetr000tor255andGandbtozero,yourunitwillshowonlyredLEDs.

Pressthe“ENTER”buttontoconrmthesettingandmovetothenextcolour.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

6 channel mode:

Channel Value Function

CH1 000-255 Reddimmer(0-100%)

CH2 000-255 Greendimmer(0-100%)

CH3 000-255 Bluedimmer(0-100%)

CH4

000-027 Nofunction

028-055 Strobe(useCH6forspeed)

056-083 Strobewithcolourchange

(useCH6forspeed)

084-111 Red

112-139 Green

140-167 Blue

168-195 Yellow

196-223 Purple

224-251 Cyan

252-255 White

CH5

000 Nofunction

001-012 Redfadein/out

(useCH6

forspeed)

013-025 Greenfadein/out

026-038 Bluefadein/out

039-051 Yellowfadein/out

052-064 Purplefadein/out

065-077 Cyanfadein/out

078-090 Whitefadein/out

091-116 Autocolourfadein/out

117-142 Colourfade

143-168 Colourchange

169-181 Colourchangewithstrobe

182-207 Allautoshows

208-255 Soundactiveash(whenCH6is000)

208-255 Soundactive(whenCH6is001-255)

CH6 000-255 Speed(slow-fast)/Sensitivity(low-high)

www.prolight.co.uk Power Par Series User Manual 5

Built-in program mode:

Toaccessbuilt-inprogrammodepress“MENU”untilthedisplayshowsPr--ontheLEDdisplay.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectbetweenPr00~Pr13.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectthespeedbetween

SP00~Sp20.Pressthe“ENTER”buttontoconrm.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Sound active mode:

Toaccessthesoundactivemode,pressthe“MENU”buttononthefrontoftheunittoshowSoudon

theLEDdisplay.Nowpressthe“ENTER”buttonandthedisplaywillshowSens.Pressthe“ENTER”

buttonagainandusethe“UP”and“DOWN”buttonstoselectthesensitivitylevelfrom000-100.

Pressthe“ENTER”buttontoconrmthesetting.

Value: 000 - 100 (000 = low,100 = high)

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Master/slave mode:

Tosetthemasterunit,pressthe“MENU”buttonontherearofthemasterunittoselectyour

desiredprogram(soundactiveorRGBcolourmix).

Tosettheotherunitsinslavemode,pressthe“MENU”buttonontherearoftheunittoshowSLav

ontheLEDdisplayandpressthe“ENTER”buttontoconrmthesetting.Theunitswillnowrunin

sequencewiththemasterunit.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Built-inprogrammode

Pr00-Pr13

Pr00-RGBcolourmixmode

r000~r255R

G000~G255G

b000~b255B

Pr01-R

Pr02-G

Pr03-B

pr04-RG

Pr05-RB

Pr06-GB

Pr07-RGB

Pr08-Colourfadein-out(3colours)

Pr09-Colourfadein-out(7colours)

Pr10-Colourfade

Pr11-Colourfadein-out(7colours)&colourfade

Pr12-Colourchange(3colours)

Pr13-Colourchange(7colours)

Slavemode SLAV

Soundactivemode SOUd

Sens

000~100

DMXmode 6CH

Addresssetting A001~A512

Menusystem

www.prolight.co.uk Power Par Series User Manual 6

Setting the DMX address:

TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”

from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel

indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas

addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105

and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe

chainstartsat107.

DMX 512:

DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent

xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.

DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”

XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).

DMX linking:

DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether

andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.

ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest

cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe

DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein

aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda

DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,

nomatterwhereitislocatedintheDMXchain.

DATA cable (DMX cable) requirements (for DMX operation):

ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.

YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,

seeimagebelow.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

FurtherDMXcablescanbe

purchasedfromallgoodsound

andlightingsuppliersor

ProLightConceptsdealers.

Pleasequote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk Power Par Series User Manual 7

Notice:

Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables

shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs

outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.

Special note:

Line termination:

Whenlongerrunsofcableareused,

youmayneedtouseaterminatoron

thelastunittoavoiderraticbehaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures

maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa

3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.

Terminationreducessignaltransmission

problemsandinterferance.itisalways

advisabletoconnectaDMXterminal,

(resistance120Ohm1/4W)betweenpin2

(DMX-)andpin3(DMX+)ofthelastxture.

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

www.prolight.co.uk Power Par Series User Manual 8

Operating instructions & WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof

withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe

environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother

typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.

Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir

localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally

saferecycling.

Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe

purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Equinox Systems Beleuchtungsausrüstung Handbücher

Equinox Systems

Equinox Systems Kaleido EQLED85 Bedienungsanleitung

Equinox Systems

Equinox Systems Nova Par 64 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED013 Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT MAX MKII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED65 Giga Bar System Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Saber Bedienungsanleitung

Equinox Systems

Equinox Systems POLARIS Bedienungsanleitung

Equinox Systems

Equinox Systems Spectra Strobe Batten Bedienungsanleitung

Equinox Systems

Equinox Systems QUADRILLE Bedienungsanleitung

Equinox Systems

Equinox Systems UV Mini Batten 9 Bedienungsanleitung

Equinox Systems

Equinox Systems TRINITY BEAM Bedienungsanleitung

Equinox Systems

Equinox Systems PIXELpoint Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Cirrus Bedienungsanleitung

Equinox Systems

Equinox Systems Axis 50W Gobo Flower Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Orbit MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Eyebar Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED040 Bedienungsanleitung

Equinox Systems

Equinox Systems Tri Power Batten MKII Bedienungsanleitung

Equinox Systems

Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung

Equinox Systems

Equinox Systems 400W UV Cannon Bedienungsanleitung

Equinox Systems

Equinox Systems SIGMA EQLA09 Bedienungsanleitung

Equinox Systems

Equinox Systems Lexor Bedienungsanleitung

Equinox Systems

Equinox Systems Swing Batten Bedienungsanleitung

Equinox Systems

Equinox Systems VIXEN EQLA36 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung