Equinox Systems TRINITY BEAM Bedienungsanleitung
Order code: EQLA42
User manual
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
Equinox Trinity Beam Laser Safety
Equinox Trinity Beam Laser Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
You should nd inside the Laser carton the following items:
1, Trinity Beam Laser 2, Power cable 3, User manual 4, Safety Keys
Technical Specications:
DMX channels: 2
Laser diodes: 1 x 80mW Green (532nM) DPSS laser, 1 x 400mW Blue (450nM) DPSS laser
1 x 300mW Red (650nM) DPSS laser
Operating modes: 1, Sound Active
2, Auto Run
3, DMX
4, Master/slave
Power consumption: 220W
Power supply: 240V - 50Hz
Dimensions: 350 x 392 x 110mm
Weight: 4.6Kgs
Fuse: 2A
Features:
The Trinity Beam Laser features 7 DMX channels and many laser patterns that are ideal with or
without fog.
Equinox Trinity Beam Laser Technical specications
Back view:
Hanging bracket positioning:
When you rst open the Trinity Beam carton, you will notice that the hanging bracket is placed on
back of the unit, this is for installation set up (g 1). For mobile rigging use, please attach the extra
brackets (included in the carton) to the additional screw holes on the side of the xture (g 2).
Fig 1
Installation set up
Fig 2
Mobile rigging set up
Operation modes:
The Trinity Beam has 4 modes of operation as follows:
1, Sound active mode
To select sound active mode set dip switch 10 to ON and all others to OFF. You can now use the
sensitivity control on the back panel to set the required sound level.
2, Auto run mode
To select auto pattern mode, set dip switch 9 and 10 to the ON position and all others to OFF.
The Trinity Beam will now cycle through all it’s internal patterns.
3, DMX mode
To select DMX mode, set dip switch 10 to OFF. You can now set the required DMX address using
dip switches 1 to 9. Please refer to the chart below for DMX functions.
The DMX address starts at 1.
4, Master/slave mode
To set the unit/s in slave mode, set dip switch 3 to the ON position and all others to OFF. The
Trinity Beam laser/s will now run in sequence with the master unit.
DMX function chart:
Equinox Trinity Beam Laser Operation modes
Example:
DMX manual mode
Channel DMX Address Function
CH.1
CH.2
0-70
71-140
141-210
211-255
Blackout
Sound active
Auto run
0-255 28 Pattern selector (CH.1, DMX manual mode)
DMX Control Mode
Operating in a DMX control mode environment gives the user the greatest exibility when it comes
to customising or creating a show. In this mode you will be able to control each individual trait of
the xture and each xture independently.
Setting the DMX address
The DMX mode enables the use of a universal DMX controller. Each xture requires a
“start address” from 1- 511. A xture requiring one or more channels for control begins to read the
data on the channel indicated by the start address. For example, a xture that occupies or uses 7
channels of DMX and was addressed to start on DMX channel 100, would read data from
channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used
do not overlap. E.g. the next unit in the chain starts at 107.
Set the start address using the group of dip switches located usually on the back of the xture.
Each dip switch has an associated value. Adding the value of each switch in the ON position will
provide the start address. Determining which switches to toggle ON given a specic start address
can be accomplished in the following manner. By subtracting the largest switch value possible
from the selected start address until zero is achieved.
on
on
EXAMPLE STARTING ADDRESS
Address 10
Pin NO: 4 = 8
Pin NO: 2 = 2
Total = 10
Address 24
Pin NO: 5 = 16
Pin NO: 4 = 8
Total = 24
DMX address using
simple maths
233 - (128 = 105,Turn on dip No: 8
105 - (64) = 41,Turn on dip No:7
41 - (32) = 9,Turn on dip No: 6
9 - (8) = 1,Turn on dip No: 4
1 - (1) = 0,Turn on dip No:1
You will most likely use the first available
number which maybe Number 1.This
number was selected for
example purposes
DIP SWITCH (DMX VALUE)
1
2
3
4
5
6
7
8
9
10
1
2
4
8
16
32
64
128
256
Equinox Trinity Beam Laser DMX control mode
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent xtures and controllers. A DMX controller sends DMX data instructions form the
controller to the xture. DMX data is sent as serial data that travels from xture to xture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have
a data “out” terminal).
DMX Linking:
• DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX xtures try to use the
shortest cable path possible. The order in which xtures are connected in a DMX line does not
inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
DATA Cable (DMX cable) requirements (for DMX operation):
• The Equinox Trinity Beam laser can be controlled via DMX-512 protocol. The DMX address is set
on the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector
for data input/output (gure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
Equinox Trinity Beam Laser DMX Set Up
Further DMX cables can be purchased from all
good sound and lighting suppliers or Prolight
dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic
behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
Equinox Trinity Beam Laser DMX Set Up
Equinox Trinity Beam Laser Dip Switch Reference Chart
DMX Dip Switch Quick Reference Chart
Dip Switch Position
Dip Switch position DMX Address
Equinox Trinity Beam Laser Safety
Class 3B Laser Lighting Effect User Safety Guide ProLight Concepts Limited
Installation and Operation Notes
1. The laser should only be installed and operated by those that are aware of how
to operate laser, and what the various controls perform. The keyswitch provided
on the laser should help to prevent use by unintended people.
2. The laser should be mounted in a suitable and secure position in the venue, so
that once in position it is unlikely to be affected by unintended movement.
3. Prior to installation and operation of the laser, the paths of the beams and
effects should be considered, particularly with respect to how they will touch the
audience. If direct audience scanning is desired then the laser energy in the
effects needs to be considered to decide if the effects are safe for direct
viewing.
Introduction
Laser lighting products are used to create some of the most vivid and striking visual effects, and
are often noted for how they seem to produce solid shapes that cut through the air, and pick up
highly dened swirling smoke patterns. The light that is used to create these stunning effects is
different from normal light and therefore several precautions need to taken when using lasers to
ensure that the lighting effects are safe and enjoyable to view. The optical power output from the
kind of lasers used for lighting displays can be harmful if not properly setup or is misused. But
when used following the recommended health and safety guidelines, laser lighting effects no more
harmful than looking at any conventional lighting effect.
This guide has been put together to provide you with some background information about laser
safety, and guidance on the recommended health and safety requirements for using lasers in
public places. Although this guide covers the main points to consider when using laser effects,
users are advised to familiarise themselves with other guidance, particularly that issued by the
Health and Safety Executive, HS(G)95 The Radiation Safety Of Lasers Used For Display
Purposes, which is freely downloadable from the HSE website. Attending one of the laser safety
training courses, listed at the end of this guide, is also highly recommended.
Important Warnings
Class 3B Lasers have the potential to harm eyesight if viewed directly in the face, and
in many instances this may be the case, even if viewed over longer distances of several
tens of metres. Therefore before using the laser product you should familiarise yourself
with its operation, and also the safety aspects that need to be considered.
Laser lighting effects are quite safe to watch if installed and used correctly, and being
aware of a few basic factors will help you to achieve this. This guide has been prepared to
help provide a basic backgrounder to the key safety aspects, and is based on current UK
health and safety guidance on the use of lasers for public displays.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Equinox Systems Beleuchtungsausrüstung Handbücher
Equinox Systems
Equinox Systems ORION Bedienungsanleitung
Equinox Systems
Equinox Systems Fusion 150 Bedienungsanleitung
Equinox Systems
Equinox Systems SCORPIO EQLA11 Bedienungsanleitung
Equinox Systems
Equinox Systems GEOMETRIX EQLA35 Bedienungsanleitung
Equinox Systems
Equinox Systems VIXEN EQLA36 Bedienungsanleitung
Equinox Systems
Equinox Systems GEMINI Bedienungsanleitung
Equinox Systems
Equinox Systems TRICLOPS EQLED50 Bedienungsanleitung
Equinox Systems
Equinox Systems VS 1500 Fogger Bedienungsanleitung
Equinox Systems
Equinox Systems Lexor Bedienungsanleitung
Equinox Systems
Equinox Systems SpectraPix Lithium Batten Bedienungsanleitung
Equinox Systems
Equinox Systems EQLED203 Bedienungsanleitung
Equinox Systems
Equinox Systems CONSTELLA Bedienungsanleitung
Equinox Systems
Equinox Systems UV Mini Batten 9 Bedienungsanleitung
Equinox Systems
Equinox Systems Domin8r IIEQLED53 Bedienungsanleitung
Equinox Systems
Equinox Systems PREDATOR Bedienungsanleitung
Equinox Systems
Equinox Systems Krypton EQLED21 Bedienungsanleitung
Equinox Systems
Equinox Systems XP 80W Bedienungsanleitung
Equinox Systems
Equinox Systems Fusion Saber Bedienungsanleitung
Equinox Systems
Equinox Systems Power Flower EQLED77 Bedienungsanleitung
Equinox Systems
Equinox Systems Interceptor MKII Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
