Equinox Systems Tri Power Batten MKII Bedienungsanleitung

Order code: EQLED035

Tri Power Batten MKII

User Manual

www.prolight.co.uk Tri Power Batten MKII User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CARE-

FULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 100~240V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is

not designed for or suitable for household use. The

product must be installed by a qualied technician in

accordance with local territory regulations. The safety of

the installation is the responsibility of the installer. The

xture presents risks of severe injury or death due to re

hazards, electric shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk Tri Power Batten MKII User Manual 3

Product overview & technical specications

The Tri Power Batten MKII is a Pixel controllable LED bar with 12 x 3W 3-in-1 RGB LEDs. Full pixel control is

available when operated in 36 channel mode to create stunning colour ows and chases but can also be

controlled in several other channel modes.

• 12 x 3W tri-colour LEDs (RGB)

• Beam angle: 38°

• 1015 Lux @ 2m (full on)

• 2kHz refresh rate

• Pixel mapping capabilities

• DMX channels: 3/3/5 or 36 selectable

• Static colour, auto, sound active and master/

slave modes plus built-in programs

• 0 -100% dimming and variable strobe

• Bracket allows for multiple rigging or oor

standing applications

• 4 push button menu with LED display

• IEC power input/output

• 3-Pin XLR input/output

• Convection cooled

Tri Power Batten MKII

Specications

Power consumption 40W

Power supply 100~240V, 50/60Hz

Fuse T1A 250V

Dimensions 88 x 1070 x 65mm

Weight 2.15kg

Order code EQLED035

0m 1m 2m 3m 4m 5m

38° - Lux

FULL ON

4040

1970

3290

952

1015

492

822

238

449

219

365

106

38°

253

123

206

59.5

162

78.7

132

38.1

1070mm 65mm

88mm

www.prolight.co.uk Tri Power Batten MKII User Manual 4

Technical specications

In the box: 1 x xture,

2 x mounting

brackets/feet

1 x power cable

& 1 x user manual

POWER INPUT:

100-240V~50/60Hz

FUSE: T1A 250V

MENU ENTER UP DOWN POWER OUTPUT

DMX INPUT DMX OUTPUT

POWER

BATTEN

MKII

TRI

www.prolight.co.uk

POWER INPUT:

100-240V~50/60Hz

FUSE: T1A 250V

MENU ENTER UP DOWN POWER OUTPUT

DMX INPUT DMX OUTPUT

POWER

BATTEN

MKII

TRI

www.prolight.co.uk

POWER INPUT:

100-240V~50/60Hz

FUSE: T1A 250V

MENU ENTER UP DOWN POWER OUTPUT

DMX INPUT DMX OUTPUT

POWER

BATTEN

MKII

TRI

www.prolight.co.uk

POWER INPUT:

100-240V~50/60Hz

FUSE: T1A 250V

MENU ENTER UP DOWN POWER OUTPUT

DMX INPUT DMX OUTPUT

POWER

BATTEN

MKII

TRI

www.prolight.co.uk

01 02

030810 05 06 0704 09

01 - Bracket tightening knobs

02 - Bracket

03 - Earth point

04 - LED display

05 - Function buttons

06 - 3-Pin XLR input

07 - 3-Pin XLR output

08 - IEC power input

09 - IEC power output

10 - Fuse T1A 250V

www.prolight.co.uk Tri Power Batten MKII User Manual 5

Operating instructions

S L a v

Slave mode

C o L r

Colour mix mode

r 0 0 0

g 0 0 0

r 2 5 5

g 2 5 5

b 0 0 0 b 2 5 5

S o u d

Sound modes

S_. 0 0

S -. 0 0

S_. 3 1

S -. 3 1

S_.00

{---

S _. 3 1

- - - }

Auto mode

A u T 0

n 0 0 1

s P 0 1

n 1 0 0

S P F L

F 5 0 0 F 5 9 9

d. 0 0 1

DMX address setting

& channel mode

d.001

d.512

3 = c h

3 - c h

5 - c h

3 6 c h

Pr--

Pr02 Pr16

S P F L

F 5 9 9

- - - }

S P 0 1

F 5 0 0

{ - - -

Built-in

programs

1 - - r

2 - r b

3 - - g

4 - g b

5 - - b

6 - r b

7 r g b

8 O F F

F 5 0 0

F 5 9 9

0 1

www.prolight.co.uk Tri Power Batten MKII User Manual 6

Operating instructions

DMX mode:

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of the

xture and each xture independently.

To access the DMX address mode, press the “MENU” button on the front of the unit to show d.001

on the LED display. Now use the “UP” and “DOWN” buttons to set the required DMX address.

Press the “ENTER” button to conrm the setting. The display will now show --ch on the LED display.

Now use the “UP” and “DOWN” buttons to choose one of the 3/3/5 or 36 DMX channel modes.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Value CH1 CH2 CH3

000 No function No function No function

001-014 Program 2

Speed

(0-255)

Flash

(0-255)

015-029 Program 3

030-044 Program 4

045-059 Program 5

060-074 Program 6

075-089 Program 7

090-104 Program 8

105-119 Program 9

120-134 Program 10

135-149 Program 11

150-164 Program 12

165-179 Program 13

180-194 Program 14

195-209 Program 15

210-224 Program 16

225-255 Sound active Sensitivity

(0-255) No function

3 channel mode 2 (3=ch):

Channel Value Function

1 000-255 Master dimmer (0-100%)

2 000-255 Red (0-100%)

3 000-255 Green (0-100%)

4 000-255 Blue (0-100%)

5 000-255 Strobe (slow-fast)

5 channel mode:

Channel Value Function

1 000-255 Red (0-100%)

2 000-255 Green (0-100%)

3 000-255 Blue (0-100%)

3 channel mode 1 (3_ch):

www.prolight.co.uk Tri Power Batten MKII User Manual 7

Operating instructions

Static colour mode:

To access the static colour mode press “MENU” until CoLr shows on the LED display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to select the brightness

between r.000 ~ r.255. Press the “ENTER” button and repeat for green (G), and blue (b).

Value: 000 - 255 (000 = low brightness, 255 = high brightness)

To exit out of any of the above options, press the “MENU” button.

Built-in programs:

To access the built-in programs, press the “MENU” button on the front of the unit to show Pr--

on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose the

required program Pr01 ~ Pr16. Press the “ENTER” button to conrm the setting.

Pr01 - Now use the “UP” and “DOWN” buttons to select the required colour. Press the “ENTER”

button to conrm the setting and use the “UP” and “DOWN” buttons to choose the ash speed

F500 ~ F599. Press the “ENTER” button to conrm the setting.

Pr02 ~ Pr16 - Now use the “UP” and “DOWN” buttons to select the running speed

SP01 ~ SPFL. Press the “ENTER” button to conrm the setting. Now use the “UP” and “DOWN”

buttons to select the ash speed F500 ~ F599. Press the “ENTER” button to conrm the setting.

Use the “UP” and “DOWN” buttons to select the fading time FS00 ~ FS99. Finally press the “ENTER”

button and use the “UP” and “DOWN” buttons to select the direction {--- or ---}.

To exit out of any of the above options, press the “MENU” button.

36 channel mode:

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12

(0-100%)

CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24

(0-100%)

CH25 CH26 CH27 CH28 CH29 CH30 CH31 CH32 CH33 CH34 CH35 CH36

(0-100%)

R10

(0-100%)

G10

(0-100%)

B10

(0-100%)

R11

(0-100%)

G11

(0-100%)

B11

(0-100%)

R12

(0-100%)

G12

(0-100%)

B12

(0-100%)

www.prolight.co.uk Tri Power Batten MKII User Manual 8

Operating instructions

Auto mode:

To access auto mode, press the “MENU” button on the front of the unit to show Auto on the LED

display. The unit will now play through all the 16 built-in programs. To select the number of times

each program is repeated press the “ENTER” button and use the “UP” and “DOWN” buttons to select

between n001 ~n100. Press the “ENTER” button then use the “UP” and “DOWN” buttons to select

the running speed SP01 ~ SPFL. Finally press the “ENTER” button and use the “UP” and “DOWN”

buttons to select the ash speed F500 ~ F599.

Press the “ENTER” button to conrm the setting.

Master/slave mode:

The default setting for this xture is Master.

To set the slave unit, press the “MENU” button on the front of the master unit to show SLav

on the LED display. The unit is now in Slave mode.

To exit out of any of the above options, press the “MENU” button.

Please ensure that all slave units are set to the same DMX channel mode as the master unit.

Sound active mode:

To access the sound active mode, press the “MENU” button on the front of the unit to show Soud

on the LED display. Now press the “ENTER” button to choose Sound mode 1 and use the “UP” and

“DOWN” buttons to choose the required sound sensitivity S-.00 ~S-.31. Press the “ENTER” button

again to choose Sound mode 2 and use the “UP” and “DOWN” buttons to choose the required sound

sensitivity S-.00 ~S-.31. Press the “ENTER” button again to choose Sound mode 3 and use the “UP”

and “DOWN” buttons to choose the required sound sensitivity S_.00 ~S_.31. Finally press

the “ENTER” button and use the “UP” and “DOWN” buttons to select the direction {--- or ---}.

Press the “ENTER” button to conrm the setting.

Value: 01 - 31 (01 = low sensitivity, 31 = high sensitivity)

To exit out of any of the above options, press the “MENU” button.

Factory reset:

To reset the xture to factory settings, power the xture off. Press and hold the “MENU” and “ENTER”

buttons whilst powering the unit up. Keep hold of the “MENU” and “ENTER” buttons for 3 seconds after

power up. The unit will now have reset to factory settings.

www.prolight.co.uk Tri Power Batten MKII User Manual 9

DMX setup

Further DMX cables can be

purchased from all good sound

and lighting suppliers or

Pro Light Concepts dealers.

Please quote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

Setting the DMX address:

The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”

from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel

indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was

addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105

and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the

chain starts at 107.

DMX 512:

DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.

DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”

XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).

DMX linking:

DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest

cable path possible. The order in which xtures are connected in a DMX line does not inuence the

DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in

a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a

DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,

no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):

This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.

Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output,

see image below.

Also remember that DMX cable must be daisy chained and cannot be split.

www.prolight.co.uk Tri Power Batten MKII User Manual 10

Notice:

Be sure to follow the diagrams below when making your own cables. Do not connect the cables

shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs

outer casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special note:

Line termination:

When longer runs of cable are used,

you may need to use a terminator on

the last unit to avoid erratic behaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a

3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.

Termination reduces signal transmission

problems and interference. it is always

advisable to connect a DMX terminal,

(resistance 120 Ohm 1/4 W) between pin 2

(DMX-) and pin 3 (DMX+) of the last xture.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Equinox Systems Beleuchtungsausrüstung Handbücher

Equinox Systems

Equinox Systems KAMIKAZE EQLA14 Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Lithium Batten Bedienungsanleitung

Equinox Systems

Equinox Systems CONSTELLA Bedienungsanleitung

Equinox Systems

Equinox Systems Gigabar MKII COB Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT XP Bedienungsanleitung

Equinox Systems

Equinox Systems Kaleido EQLED85 Bedienungsanleitung

Equinox Systems

Equinox Systems Eyebar Bedienungsanleitung

Equinox Systems

Equinox Systems Krypton EQLED21 Bedienungsanleitung

Equinox Systems

Equinox Systems Terminator 2 Bedienungsanleitung

Equinox Systems

Equinox Systems SIGMA EQLA09 Bedienungsanleitung

Equinox Systems

Equinox Systems TRICLOPS EQLED50 Bedienungsanleitung

Equinox Systems

Equinox Systems PIXELpoint Batten Bedienungsanleitung

Equinox Systems

Equinox Systems UV Mini Batten 9 Bedienungsanleitung

Equinox Systems

Equinox Systems Axis 50W Gobo Flower Bedienungsanleitung

Equinox Systems

Equinox Systems TRINITY BEAM Bedienungsanleitung

Equinox Systems

Equinox Systems XP 80W Bedienungsanleitung

Equinox Systems

Equinox Systems Goboceptor Bedienungsanleitung

Equinox Systems

Equinox Systems Lexor Bedienungsanleitung

Equinox Systems

Equinox Systems Spectra Strobe Batten Bedienungsanleitung

Equinox Systems

Equinox Systems ORION Bedienungsanleitung

Equinox Systems

Equinox Systems Saturn Spot Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED65 Giga Bar System Bedienungsanleitung

Equinox Systems

Equinox Systems Interceptor MKII Bedienungsanleitung

Equinox Systems

Equinox Systems CARINA Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung