ESAB SDF-250 Bedienungsanleitung

SDF-250 STATIONARY SUBMERGED ARC WELDING POWDER

DRYING OVEN

0700 100 000 THREE PHASE 400V AC 50/60Hz

0700 100 001 ONE PHASE 110V AC 50/60Hz

INSTRUCTION MANUAL FOR SUBMERGED ARC WELDING POWDER DRYING OVEN

USAGE PURPOSE

This product is designed to dry and hold the

submerged arc welding powders at a certain

temperature. Welding powders can be dried for

the period recommended by the manufacturer,

depending on the conditions. It should only be

used in the intended use direction to avoid

possible damage to property and injuries.

BEFORE USING

Make sure that the technical specification on

the product corresponds to the electrical supply

in your network. Check the voltage and

frequency information. Check that there are no

fault that will affect the operation of the

product.

USAGE ENVIRONMENT

Flammable and explosive materials should not

be around the device. The device it should not

be covered. It should be run in a dry place.

Never use it in the rain and wet ground.

USING

Connect the appliance plug to the power supply by attaching a socket. Turn the switch to position (1) on

the top of the main panel. To set the temperature above the Digital Controller; Press and hold the SET

key for 2 seconds. Select the temperature with the Up and Down keys and press the SET key again. The

device will automatically switch off the heating when it reaches the desired temperature. The three

pilot lamps (side-by-side) on the panel show three electrical phases. If one or two does not, there is a

problem with your electricity line. 3 light should blink at the same moment. The lamps turn on during

heating. If the oven has reached the desired temperature, the lamps will turn off. Charge of the welding

powders into the top cover, do not put any other material, package, etc. from the welding powder into

the chamber. Leave a little high to hard to close the door. The lock will be fully seated. When you want

to use the welding powders, pull the lower arm than powder will discharge into a bucket. When the

bucket is full push back the arm. If you are not using the oven, turn the switch to position (0) and unplug

it. Some surfaces may be hot to the touch, use heat resistant fireproof gloves. Do not touch live parts

with electrical shock hazard.

SDF-250 Technical Information

Capacity

250 Kg (551 lb) Flux

Voltage

3 ph 400V, 3ph 230V 50/60Hz

Power

7.500 W

Temperature

0-400 °C (32-752 °F) Digital Thermostate

Storage Size L-W-H

2 pcs 45x51x60 cm, 17,71x20,07x23,62 in

Outer Dimensions

162x82x145 cm, 63.77x32,28x57,08 in

Weight

230 kg (507 lb)

ESAB Group (UK) Ltd, 322 High Holborn, 6th Floor, London,WC1V 7PB,United Kingdom www.esab.com

SCHEMATIC DIAGRAM OF SDF-250

SPARE PARTS LIST

ITEM NO

QTY

ORDERING NO

DESCRIPTION

NOTES

0700 100 002

Digital Thermostate

DT-109A

0700 100 003

Signal Lamp

220V

0700 100 004

Signal Lamp

110V

0700 100 006

Door Handle

0700 100 007

Puller Arm

0700 100 008

Castors without Brake

Back

0700 100 009

Castors with Brake

Front

0700 100 031

Cable Gland

0700 100 011

Heating Element

220V

0700 100 012

Heating Element

110V

0700 100 013

Power cable with plug

CEE 5x32A 400V plug

0700 100 014

Power cable with plug

110V

0700 100 015

Fuse (automatic)

10A

0700 100 016

Fuse (automatic)

0700 100 017

Contactor 220V UNI

220V

0700 100 023

Contactor 110V UNI

110V

0700 100 018

Power Switch

0700 100 019

Terminal

set

0700 100 020

Air Valve

0700 100 164

Fiberglass Wick

SDF-250

0700 100 165

Thermocouples

CONTROL PANEL

Andere Handbücher für SDF-250

Dieses Handbuch passt für folgende Modelle

Andere ESAB Schweißzubehör Handbücher

ESAB

ESAB A6S Arc Master Bedienungsanleitung

ESAB

ESAB PSF 250 Bedienungsanleitung

ESAB

ESAB SDF-50 Bedienungsanleitung

ESAB

ESAB 1500 ahma Bedienungsanleitung

ESAB

ESAB Eye-Tech 10-12 Select Bedienungsanleitung

ESAB

ESAB Eye-Tech 10-12 Select Bedienungsanleitung

ESAB

ESAB PEI Bedienungsanleitung

ESAB

ESAB WeldCloud Mobile Bedienungsanleitung

ESAB

ESAB A2 S GMAW Mini Master Bedienungsanleitung

ESAB

ESAB LAF 1601M Bedienungsanleitung

ESAB

ESAB PT-31XL Bedienungsanleitung

ESAB

ESAB Origo Feed 304 P4 Leitfaden

ESAB

ESAB Aristo MA4 Bedienungsanleitung

ESAB

ESAB TIGAID315 AC/DC Bedienungsanleitung

ESAB

ESAB TR-29 Bedienungsanleitung

ESAB

ESAB A6 OPC Bedienungsanleitung

ESAB

ESAB PC-900 Bedienungsanleitung

ESAB

ESAB EFU 30 Bedienungsanleitung

ESAB

ESAB Sentinel A50 Bedienungsanleitung

ESAB

ESAB MT-400EHD Bedienungsanleitung

ESAB

ESAB A6 GMD Bedienungsanleitung

ESAB

ESAB CIGWELD 454342 Bedienungsanleitung

ESAB

ESAB PREST-O-LITE PZ-503 Bedienungsanleitung

ESAB

ESAB PSF 305 Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Lincoln Electric

Lincoln Electric LT-7 Tractor Bedienungsanleitung

Weco

Weco Trolley R Bedienungsanleitung

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

optrel

optrel lifeflip autopilot Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung