ESAB SDF-50 Bedienungsanleitung

SDF-50

Instruction manual

0448 023 001  GB  20230315

TABLE OF CONTENTS

0448 023 001 -3- © ESAB AB 2023

1 SAFETY ...................................................................................................................................... 4

1.1 Meaning of symbols .................................................................................................... 4

1.2 Safety precautions ...................................................................................................... 4

2 INTRODUCTION ......................................................................................................................... 4

2.1 Oven use and purpose................................................................................................ 4

3 TECHNICAL DATA ..................................................................................................................... 5

4 INSTALLATION........................................................................................................................... 5

4.1 Operation...................................................................................................................... 5

ORDERING NUMBERS ......................................................................................................................... 6

WIRING DIAGRAM ................................................................................................................................ 7

ORDERING SPARE PARTS .................................................................................................................. 8

1  SAFETY

0448 023 001 -4- © ESAB AB 2023

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate, serious

personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual and

follow all labels, employer´s safety practices and Safety Data

Sheets (SDSs).

1.2 Safety precautions

ELECTRIC SHOCK - Can kill

• Do not touch live electrical parts or electrodes with bare skin, wet gloves

or wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe.

FIRE HAZARD

• Do not use if the power cord is broken or abnormal temperature variation

(not recommended as per manual/factsheet) seen on the oven as it may

can cause fire.

• Make sure that there are no inflammable materials nearby.

HOT SURFACE - Parts can burn

• Do not touch parts bare handed.

• Allow cooling period before handling or working with the equipment.

• To handle hot parts, use proper tools and/or insulated welding gloves to

prevent burns.

2 INTRODUCTION

2.1 Oven use and purpose

The SDF-50 range of drying and storing ovens are large temperature-controlled cabinets for welding

powder flux in a typical industrial set up. They are designed for convenient top loading and bottom

removal of welding flux. The easy-to-use digital controller sets and regulates the temperature over a

wide range for baking, drying, and storing. Electric heaters embedded inside walls evenly heat the flux

without needing agitation or flux turning. Heavy insulation, rugged industrial design, external surfaces

electrostatic paint coating, heavy lockable castors make these ovens a great investment for long term

easy use.

4  INSTALLATION

0448 023 001 -5- © ESAB AB 2023

3 TECHNICAL DATA

SDF-50

Capacity 50kg (110lbs.)

Voltage 3 phase 380-415V

Frequency 50/60Hz

Output 3000W

Temperature Up to 400°C (752°F) Digital thermostat

Outer dimensions (L*W*H, cm) 107 × 67 × 113

Weight (Without electrodes) 110kg (242lbs.)

NOTE!

Oven heating temperature can be set from surrounding ambient to 400°C.

4 INSTALLATION

NOTE!

Make sure that the technical specification on the product corresponds to the electrical supply

in your network.

Check the voltage, frequency information and check that there is no fault that will affect the

operation of the product.

4.1 Operation

WARNING!

When the oven is not in use, turn the power knob to “O” position and remove power cord plug

from electrical outlet.

• Connect oven power cord plug to a power outlet as recommended in the technical

information. Make sure the power outlet socket matches the oven power plug type.

• Lock the door after the required amount of flux loaded (up to 50 kg).

• Lock the door.

• On the oven control panel, to turn on the oven change power knob to “I” position.

• Once the power is turned on, depending upon the type of your oven i.e 1Φ one green

lamp will glow or 3Φ three green pilot lamps will glow. If the lamps or not glowing,

then check the power connection. Refer the below image.

APPENDIX

0448 023 001 -6- © ESAB AB 2023

• Setting the desired temperature

○ When the unit is turned on the controller display will show the current

temperature and set value.

○ Press and hold the SET button for 2 seconds to set a different

temperature. Use up and down keys to reach the desired set

temperature. Once the controller read out shows the desired

temperature, press SET key again.

○ The oven will now automatically heat up or cool down to the set

temperature. The oven will automatically turn off heating when the set

temperature is reached. The green lamp will also turn off.

• To use the welding powder, place a 5-gallon bucket underneath the oven spout. Pull

the lower arm to discharge powder into the bucket. When the bucket is full or enough

flux has been removed, push back the arm.

○ Open and release the release valve on the top to avoid the hot smoke

exhaust when opening the front door.

APPENDIX

ORDERING NUMBERS

Ordering number Denomination Type Notes

0700 100 021 Stationary submerged arc welding powder

drying oven

SDF-50 Three phase

380-

415VAC50/60Hz

Technical documentation is available on the Internet at: www.esab.com

APPENDIX

0448 023 001 -7- © ESAB AB 2023

WIRING DIAGRAM

APPENDIX

0448 023 001 -8- © ESAB AB 2023

ORDERING SPARE PARTS

Item no. Qty. Ordering number Description Notes

1 1 0700 100 002 Digital thermostat DT-109A

23 0700 100 003 Signal lamp 220V

3 0700 100 004 Signal lamp 110V

3 1 0700 100 006 Door handle

4 1 0700 100 028 Puller arm

52 0700 100 008 Castors without brake Back

2 0700 100 009 Castors with brake Front

6 1 0700 100 031 Cable gland

72 0700 100 011 Heating element 220V

2 0700 100 012 Heating element 110V

8 1 0700 100 020 Air valve

9 1 0700 100 018 Power switch

10 2 0700 100 015 Fuse (automatic) 10A

1 0700 100 016 Fuse (automatic) 2A

11 1 0700 100 017 Contactor 220V UNI 220V

1 0700 100 023 Contactor 110C UNI 110V

12 1 0700 100 019 Terminal

13 1 0700 100 013 Power cable with plug CEE 5x32A 400V plug

1 0700 100 014 Power cable with plug 110V

14 1 0700 100 163 Fiberglass wick SDF-50

15 1 0700 100 165 Thermocouples

APPENDIX

0448 023 001 -9- © ESAB AB 2023

For contact information visit http://esab.com

ESAB AB, Lindholmsallén 9, Box 8004, 402 77 Gothenburg, Sweden, Phone +46 (0) 31 50 90 00

manuals.esab.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißzubehör Handbücher

ESAB

ESAB MT-400EHD Bedienungsanleitung

ESAB

ESAB Aristo MA4 Bedienungsanleitung

ESAB

ESAB A6 S Arc Master Bedienungsanleitung

ESAB

ESAB A6 OPC Bedienungsanleitung

ESAB

ESAB A6 VEC Bedienungsanleitung

ESAB

ESAB SABRE V J28 Bedienungsanleitung

ESAB

ESAB PSF 250 Bedienungsanleitung

ESAB

ESAB A6S Arc Master Bedienungsanleitung

ESAB

ESAB TIGAID315 AC/DC Bedienungsanleitung

ESAB

ESAB LAF 1601M Bedienungsanleitung

ESAB

ESAB CIGWELD Arcmaster 649 Payday Bedienungsanleitung

ESAB

ESAB Sentinel A60 Bedienungsanleitung

ESAB

ESAB PT-31XL Bedienungsanleitung

ESAB

ESAB PREST-O-LITE 02X93 Bedienungsanleitung

ESAB

ESAB EFU 30 Bedienungsanleitung

ESAB

ESAB CIGWELD 454342 Bedienungsanleitung

ESAB

ESAB 1500 ahma Bedienungsanleitung

ESAB

ESAB Warrior YardFeed 200 Bedienungsanleitung

ESAB

ESAB Eye-Tech 9-13 Bedienungsanleitung

ESAB

ESAB A6 Mastertrac Bedienungsanleitung

ESAB

ESAB SAVAGE A40 Bedienungsanleitung

ESAB

ESAB SDE-250 Bedienungsanleitung

ESAB

ESAB PEI Bedienungsanleitung

ESAB

ESAB ET 17 Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Lincoln Electric

Lincoln Electric LT-7 Tractor Bedienungsanleitung

Weco

Weco Trolley R Bedienungsanleitung

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

optrel

optrel lifeflip autopilot Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung