ETC ColorSource Spot Bedienungsanleitung

ETC Installation Guide

ColorSource Spot v1.7

Corpora te He adqua rte rs Middleton, WI, USA +1 608 831 4116

London, UK +44 (0)20 8896 1000 Holzkirc he n, DE +49 (80 24) 47 00-0

Rome , IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535

Web etcconnect.com Support support.etcconnect.com

Product information and specifications subject to change. ETC intends this document

to be provided in its entirety. Trademark and patent info:etcconnect.com/ip

7413M2100-1.7 Rev C Released 2020-03

Overview

The ColorSource Spot is an affordable LED fixture that uses the RGB-L (red,

green, blue, and lime) color system to provide a rich, bright light.

The ColorSource Spot is available in both original and Deep Blue variants. The

Deep Blue uses an array that offers richer, more saturated blues and stronger

magentas in exchange for the more jewel-toned blues like sky or turquoise.

For more information, see the ETC website at etcconnect.com.

The ColorSource Spot is UL924 listed as a Directly Controlled Luminaire for

use in emergency lighting systems when used with the ETC DMX Emergency

Bypass Controller (DEBC).

This light engine can be used with standard ETC shutter barrels, lens tubes,

fresnel adapters, CYC adapters, and accessories.

Note:

Features described in this document require the latest version

of software. For information on updating fixture software, see Update

the Fixture Software on page10.

ETC Installation Guide

ColorSource Spot v1.7

Safety

For professional use only. Read the entire manual before using this

equipment.

CAUTION:

•

Risk of eye injury. Do not stare directly into the light.

•

Do not operate in proximity to flammable materials.

WARNING: Disconnect the fixture from power and DMX and

allow it to cool before performing any cleaning and maintenance.

WARNING: The ColorSource Spot is a Directly Controlled

Luminaire suitable for use in emergency lighting applications in

accordance with 2017 National Electrical Code section 700.24

when used with an ETC DMX Emergency Bypass Controller.

Equipment intended for this purpose must be properly selected,

installed, and maintained so that facility conformance can be

obtained. Installation and servicing shall be performed by

qualified service personnel.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be

followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

•

Do not use outdoors.

•

Do not let power supply cords touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should be mounted in locations and at heights where it

will not readily be subjected to tampering by unauthorized

personnel.

•

The use of accessory equipment not recommended by the

manufacturer may cause an unsafe condition.

•

Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS

ColorSource Spot Page 2 of 12 ETC

ETC Installation Guide

ColorSource Spot v1.7

Note:

The light source in this luminaire is not user-replaceable, and

must be replaced only by a qualified technician. Contact ETC

Customer Support for assistance.

Environment

The ColorSource Spot operates in ambient temperatures of 0°C–40°C and

comes with a variable-speed fan. The ColorSourceSpot is for indoor use only.

•

Maximum recommended ambient operating temperature: Ta=40°C

(104°F)

•

Maximum anticipated external surface temperature at 40°C ambient:

Tmax = 80°C (176°F)

•

External temperatures after 5 minutes of full-brightness operation at

25°C (77°F) ambient: 30°C (86°F)

•

External Temperature (steady state achieved) at 25°C (77°F): 36°C

(97°F)

Electrical

•

Operates between 100V and 240VAC at a frequency of 50/60Hz.

•

Maximum power consumption is 185 W.

•

Up to 9 luminaires(15 A max) may be linked via power thru connector

(10 luminaires total per circuit) when used with an R20Relay Module

or Unison Echo Relay Panel. Consult breaker trip curves when used

with other equipment. Requires power from a non-dimmable source.

•

Inrush:

120 V: 28 A (first half-cycle)

240 V: 46 A (first half-cycle)

Typical Power Consumption

100 V 120 V 230 V

Power Current Power Current Power Current

Idle 1.19 W 0.05 A 2.07 W 0.05 A 1.5 W 0.05 A

Direct at Full 168 W 1.69 A 166 W 1.39 A 166 W 0.72 A

ColorSource Spot Page 3 of 12 ETC

ETC Installation Guide

ColorSource Spot v1.7

Installation

Emergency Lighting Considerations

Luminaires that are used in emergency lighting applications must provide a

minimum illumination level over the identified means of egress path in

accordance with the Life Safety Code®, NFPA 101. A luminaire that is intended

to serve this purpose must be mounted at a height where it will not readily be

subjected to tampering by unauthorized personnel and where the minimum

required illumination level over the egress path can be achieved. The ETC

DMX Emergency Bypass Controller that is driving the luminaire upon loss of

utility power must be programmed to drive the ColorSource Spot to full

illumination.

Install a Shutter Barrel

Small screw (included

with shutter barrel)

Light

engine

The ColorSource Spot can be

purchased with or without a shutter

barrel. To install a shutter barrel you

will need a #2 Phillips screwdriver

(not provided).

The ColorSource light engine

includes a barrel screw. The small

screw used to secure the top of the

shutter barrel is included with the

shutter barrel.

1. Align the barrel to the front of the ColorSource Spot and rotate it one

quarter turn counter-clockwise.

2. Insert the shutter barrel into the front of the light engine and rotate

clockwise until it is fully threaded onto the light engine.

3. Insert the barrel screw at the bottom of the light engine and tighten.

4. Insert the small screw into the top of the light engine and tighten

using the Phillips screwdriver.

ColorSource Spot Page 4 of 12 ETC

ETC Installation Guide

ColorSource Spot v1.7

Mounting

The ColorSource Spot ships with a standard yoke for mounting with a clamp.

You can adjust the position of the yoke when necessary for low-clearance

mounting.

Standard yoke position Low-clearance yoke position

Safety Cable

A safety cable (or other approved safety device) must be attached to the

fixture. Attachment loops are on the rear of the fixture. Take care to leave as

little slack as possible in the safety cable to avoid catching the yoke of the

fixture.

Connectors

•

Power: Two powerCON®connectors for power in and thru

•

Data (DMX512/RDM): Two five-pin XLR connectors OR two

RJ45connectors for data in and thru

Conversion cables are available from ETC. Please contact your ETC customer

service representative and request part number W6538 for RJ45 to female

XLR or part number W6539 for RJ45 to male XLR.

Note:

This fixture is not Ethernet/data network compatible.

Note:

The ColorSource Spot is not self terminating. You must

terminate the last fixture in line with a 120 Ohm resistor.

XLRterminators are not available from ETC.

To purchase an RJ45 terminator, please contact ETC customer service

and request part number N4086.

ColorSource Spot Page 5 of 12 ETC

ETC Installation Guide

ColorSource Spot v1.7

Set Up the Fixture

1. Plug the power cord into the powerCON In connector on the rear of

the fixture.

2. Make any power-thru cable connections prior to applying a power

source.

3. Make any DMX connections, and if the fixture is the last in a DMX line,

terminate the fixture. See

Connectors on the previous page

4. Plug the power cord into the power source.

Data in Data thru

Mode Up and Down

User interface

Power

thru

Safety cable

attachment

loops

Power Up

Press any button to wake the display. The display shows the DMX address.

See

Set the DMXAddress below

You can press the Mode button to access the Presets/Sequences menu. See

Play Presets and Sequences on page8

Adjust the Tilt

The fixture can be tilted up and down and rotated (panned) as needed.

1. Loosen, but do not remove the yoke locking knobs.

2. Tilt the fixture to the desired angle.

3. Tighten the yoke locking knobs.

Set the DMXAddress

1. Press any button to wake the display. The display shows the DMX

address.

2. Use the Up and Down buttons to select the DMX address for the

fixture.

You can also use RDM for DMX addressing. See

RDM Values on page11

ColorSource Spot Page 6 of 12 ETC

ETC Installation Guide

ColorSource Spot v1.7

Change the DMXControl Mode

You can set the DMX control mode for the fixture to one of four available

mode options.

1. Press any button to wake the display. The display shows the DMX

address.

2. Press and hold the Mode button for 3 seconds. The display shows the

current DMX control mode.

3. Press the Up button or Down button to change the DMX control

mode:

•

5ch: 5-channel mode (intensity, red, green, blue, and strobe). This

is the default mode.

•

dir: Direct emitter control (intensity, red, green, blue, indigo,

lime, and strobe).

•

1ch: 1-channel mode controls the intensity of preset 1 (defaults

to 3200K White).

•

rgb: RGB mode (red, green, and blue).

4. Press the Mode button to confirm your selection.

The display will automatically return to the DMX address after 10 seconds of

inactivity, and edits to the DMX control mode will not be saved. This cancels

unsaved changes.

DMXControl Channels

DMX

Channel

5ch

(5 channel)

dir

(Direct)

1ch

(1 Channel)

rgb

(RGB)

1 Intensity Intensity Intensity Red

2 Red Red Green

3 Green Green Blue

4 Blue Blue/Indigo*

5 Strobe** Lime

6 Strobe**

*Original ColorSource Spot fixture uses blue in channel 4; Deep Blue fixture uses indigo in

channel 4.

**Use DMX values of 0 or 255 for no strobe. Use values of 1–254 to increase the strobe rate

from 1 per second up to 33 per second.

ColorSource Spot Page 7 of 12 ETC

ETC Installation Guide

ColorSource Spot v1.7

Data Loss Behavior

When DMX data is lost, the fixture does one of the following actions:

•

If you selected a preset or sequence, that preset or sequence

automatically plays.

•

If no preset or sequence is active in the background, the fixture goes

dark and the DMXstart address flashes on the user interface.

Play Presets and Sequences

The fixture has twelve factory-configured presets and five factory-configured

sequences. When you play a preset or sequence on a fixture, the same preset

number or sequence number plays on any connected fixtures that are not

receiving DMX. You can re-record presets and sequences through an RDM

device or manually on the fixture. See

Re-record Presets on the facing page

1. Press the Mode button to activate the Presets/Sequences menu. The

last active preset or sequence plays automatically. (If DMX data is

present, the current preset or sequence plays in the background and

DMX data continues to take priority.)

2. Press the Up button or Down button as needed to scroll through the

available presets and sequences.

3. To stop the selected preset or sequence, press the Mode button a

second time. The display will revert to show the DMX start address.

Pre-configuredPresets

Preset Name

1 3200 K White

2 5600 K White

3 Red

4 Green

5 Blue

6 Cyan

Preset Name

7 Magenta

8 Yellow

9 Orange

10 Light Yellow

11 Light Blue

12 Light Pink

ColorSource Spot Page 8 of 12 ETC

ETC Installation Guide

ColorSource Spot v1.7

Pre-configuredSequences

Sequence Name

1 Rainbow Fast

2 Rainbow Slow

3 Warm Colors Fast

4 Cool Colors Fast

5 Random

Re-record Presets

1. Using DMX, set the desired levels for the new preset.

2. Press the Mode button to access the Presets/Sequences menu.

3. Press the Up button or Down button to navigate to the preset number

that you want to re-record.

4. Press and hold the Mode button for 3 seconds to confirm the preset

selection. The user interface will show a 3-second countdown. The

preset number blinks once to confirm that the preset has been

recorded.

Note:

When the fixture is in Direct mode (dir) or 1-channel mode

(1ch), you cannot re-record presets.

When you re-record presets with the fixture in RGB mode (rgb), the

intensity is set to full and the strobe is turned off.

See Change the DMXControl Mode on page7.

Adjust the Intensity of Presets

1. Ensure that DMX data is not present.

2. Press the Mode button to access the Presets/Sequences menu, and

then press the Up button or Down button to select the preset that you

want to edit.

3. Press and hold the Mode button for 3 seconds. The display shows L:

followed by either an intensity level from 0–99 or FL for full.

4. Press the Up button or Down button to change the intensity level of

the preset in real time.

5. Press the Mode button to confirm your selection and return to the

Presets/Sequences menu.

The display will automatically return to the Presets/Sequences menu after 10

seconds of inactivity, and edits to the preset intensity will not be saved.

ColorSource Spot Page 9 of 12 ETC

ETC Installation Guide

ColorSource Spot v1.7

Lock the User Interface

After you have set up the fixture, you can lock the user interface to prevent

additional changes.

1. Press and hold the Up button and Down button simultaneously for

3seconds. The display will show Loc to indicate that the user interface

is locked.

2. To unlock the user interface, press and hold the Up button and Down

button simultaneously for 3 seconds.

Update the Fixture Software

ETC recommends using UpdaterAtor software to manage software updates.

For more information on UpdaterAtor, see the

UpdaterAtor Software Quick

Guide

, which you can download for free from etcconnect.com.

When you add a ColorSource fixture running a newer software version or

update a ColorSource fixture to a newer software version using UpdaterAtor,

you can use that fixture to push the newer software version to all connected

ColorSource fixtures, except for ColorSource Spotjr fixtures. ColorSource

Spotjr fixtures can only update (and be updated by)other ColorSource Spotjr

fixtures.

You can push newer software versions from a connected fixture only on

ColorSource fixtures running software v1.3.0 or newer. Use UpdaterAtor to

update individual fixtures running versions older than v1.3.0.

1. Remove power and DMX In from the master fixture that is running the

software version that you want to push to other fixtures.

2. Press and hold the Up button and Down button simultaneously while

restoring power.

3. The display will show Udt rdy to indicate the update mode is

selected.

4. Press the Mode button to start the update process.

•

The display will alternate between Udt and the percentage

complete while updating.

•

The master fixture will reboot once the update is complete.

5. Reconnect DMX In on the master fixture.

Restore Factory Defaults

Press and hold the Mode button, Up button, and Down button

simultaneously for 5 seconds. The DMX start address will blink once to

confirm that defaults have been restored.

ColorSource Spot Page 10 of 12 ETC

Andere Handbücher für ColorSource Spot

Inhaltsverzeichnis

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC Desire D22 Bedienungsanleitung

ETC

ETC Source 4WRD II Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC Cyberlight LED Bedienungsanleitung

ETC

ETC High End Systems SolaPix 19 Bedienungsanleitung

ETC

ETC High End Systems SolaPix 7 Bedienungsanleitung

ETC

ETC Source 4WRD Bedienungsanleitung

ETC

ETC Source Four Mini LED Bedienungsanleitung

ETC

ETC IRIDEON AR500 Bedienungsanleitung

ETC

ETC Aero Wave Station Bedienungsanleitung

ETC

ETC Express Bedienungsanleitung

ETC

ETC High End Systems SolaFrame 3000 Bedienungsanleitung

ETC

ETC Irideon WLZ Bedienungsanleitung

ETC

ETC Sensor IQ Contact Input Control Option Card Bedienungsanleitung

ETC

ETC Source Four Revolution Scroller Cartridge Bedienungsanleitung

ETC

ETC Desire Fresnel Bedienungsanleitung

ETC

ETC ColorSource PAR Bedienungsanleitung

ETC

ETC Source Four LED series Bedienungsanleitung

ETC

ETC Expression 2.0 Bedienungsanleitung

ETC

ETC XDLT Bedienungsanleitung

ETC

ETC Irideon WLZ Bedienungsanleitung

ETC

ETC fos/4 Fresnel Bedienungsanleitung

ETC

ETC Source Four PARNel CE Bedienungsanleitung

ETC

ETC High End Systems SolaPix 7 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung