Eureka 410 SERIES Bedienungsanleitung

Lightweight Upright

VACUUM CLEANER

OWNER’S GUIDE

410 SERIES

Index

Important Safeguards.................. 2

General Information .................... 4

Assemble .................................... 5

Use ........................................... 5-6

Accessories ................................. 7

Filter ............................................ 8

Dust Cup ..................................... 9

Brush Roll.................................. 10

Brush Roll Belt .......................... 10

Customer Order Form ............... 11

Warranty .................................... 13

www.eureka.com

Household Type

IMPORTANT

Do not return this

product to the store.

For assembly problems or

questions contact: Eureka’s

Customer Service Division

toll free at 1-800-282-2886*, 7

a.m. to 8 p.m., Central Standard

Time, Monday through Saturday.

For replacement of broken or

missing items to be shipped

direct to you, call 1-800-438-

7352*, 8 a.m. to 4:45 p.m.,

Central Standard Time, Monday

through Friday.

*En Mexico llame al 5670-6169.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.

WARNING

To reduce the risk of fire, electric shock, or injury:

•Do not use outdoors or on wet surfaces.

•Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug

the electrical cord when not in use and before servicing.

•Do not allow to be used as a toy. Close attention is necessary when used by or near

children.

•Use only as described in this manual. Use only manufacturer’s recommended

attachments.

•Do not use with damaged cord or plug. If vacuum cleaner is not working as it should,

has been dropped, damaged, left outdoors, or dropped into water, return it to a

service center before using.

•Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord

around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord

away from heated surfaces.

•Connect to a properly grounded outlet only (refer to Grounding Instructions).

•Do not use extension cords or outlets with inadequate current carrying capacity.

•Turn off all controls before unplugging.

•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

•Do not handle plug or vacuum cleaner with wet hands.

•Do not put any object into openings. Do not use with any opening blocked; keep free

of dust, lint, hair, and anything that may reduce airflow.

•This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair,

loose clothing, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or

hot ashes.

•Do not use without dust bag in place.

•Belt pulleys can become hot during normal use. To prevent burns, avoid touching

the belt pulley when servicing the drive belt.

•Use extra care when cleaning on stairs.

•Do not use to pick up flammable or combustible liquids such as gasoline, or use in

areas where they may be present.

•Store your cleaner indoors in a cool, dry area.

•Keep your work area well lighted.

•Unplug electrical appliances before vacuuming them.

SAVE THESE INSTRUCTIONS

CONSEILS DE SÉCURITÉ

Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent

être observées, incluant les suivantes:

LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.

AVERTISSEMENT

Pour réduire le risque de feu, de choc électrique ou blessure:

•N’utilisez pas a l’extérieur ou sur une surface mouillée.

•Ne quitte pas l’aspirateur lorsqu’il est branche. Fermer le poste et débrancher la

corde électrique lorsqu’il n’est pas en marche et/ou avant de le repérer.

•N’utilisez pas comme un jouet. Portez attention l’orsque vous l’utilisez pies ou par un

enfant.

•Utilisez seulement comme décrit dans ce livret. Utilisez seulement les accessoires

recommandes par le fabricant.

•N’utilisez pas avec une corde ou prise endommagée. Si l’aspirateur ne fonctionne

pas comme il le faut, s’y il a été échappe, endommage, laisse a l’extérieur, ou échappe

dans l’eau, retourne l’aspirateur a un centre de réparation avant de s’en servir.

•Ne tirez pas et ne portez pas par le corde, utilisez la corde comme une poignée,

fermez un porte sur la corde, ou tirez la corde autour des coins aigu. Ne passez pas

l’aspirateur sur la corde. Éloignez la corde des surfaces chaudes.

•Branchez toujours l’aspirateur dans une prise à trois (mise à la terre).

•N’utilisez pas la corde électrique ou la prise de courant avec insuffisamment de

capacité de courant.

•Fermez tout les contrôle avant de débrancher.

•Ne débranchez pas en tirant sur la corde. Pour débrancher saisir la prise, non

la corde.

•Ne touchez pas la prise ou l’aspirateur avec les mains mouillées.

•Ne mettez aucun objets dans les ouvertures. N’utilisez pas avec des ouvertures

bouches; gardez libre de poussière, tissue ouate, cheveux et n’importe quoi qui peut

réduire la courant atmosphérique.

•Cet aspirateur crée de la succion. Quelque modèles contient un rouleau-brosse

tournant. Tenir les parties mobiles et les ouvertures loin des cheveux, des habits,

des doigts et de toute partie du corps.

•Ne ramassez rien qui brûle ou fument, tel que cigarettes, allumettes, ou des cendres

chaudes.

•N’utilisez pas sans le sac de poussière en place.

•Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour

prévenir des brûlures, évitez de touché la poulie du courroie lorsque vous réparez la

courroie.

•Utilisez des précautions lorsque vous nettoyé sur des escaliers.

•N’utilisez pas pour ramasser des liquides inflammable ou combustible, tel que de

l’essence, ou utilise dans les endroits ou ses derniers peuvent être présent.

•Entreposez votre aspirateur a l’intérieur dans un endroit propre et sec.

•Garder votre lieu de travail bun éclaire.

•Débrancher les appareils électrique avant de les balayer.

CONSERVEZ CES INSTRUCTIONS

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is

wider than the other).This plug will fit in a polarized outlet only one way. If the plug does

not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install the proper outlet. Do not change the plug in any way.

Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche polarisée

(une des lames est plus large). Cette fiche ne peut être insérée dans une prise polarisée

que d’une seule façon. Si la fiche ne peut être insérée dans la prise, retourner la fiche.

Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate

par un électricien qualifie. Ne pas modifier la fiche.

GENERAL INFORMATION

Use the cleaner to pick up dirt and dust particles. Avoid picking up hard or sharp objects

that could damage the vacuum cleaner.

Service Information

The instructions in this booklet serve as a guide to routine maintenance. For additional

service information, telephone our toll free number for the nearest Eureka Authorized

Warranty Station. You should know the model, type and serial number or date code

when you call: USA: 1-800-282-2886

Mexico: 5670-6169

Canada: 1-800-282-2886

If you prefer, you can write to The Eureka Company, Service Division, 807 North Main

St., Bloomington, Illinois 61701, USA. In Canada, write to The Eureka Company, 866

Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Warranty for complete

service information.

DO NOT OIL the motor or the brush roll. The motor and brush roll are

permanently sealed and lubricated.

Rating Plate

The rating plate on the back of the vacuum

cleaner shows the model number. For prompt

and complete service, always refer to these

numbers.

Model and Type No. __________________

Serial No. or Date Code _______________

THE EUREKA COMPANY

BLOOMINGTON, ILLINOIS 61701 USA

HOUSEHOLD TYPE

MODEL TYPE SERIAL #

HOW TO USE

HOW TO ASSEMBLE

3 Position

ON/OFF

Switch

To assemble the cleaner, find the powerhead (a)

and the body (b). Align the connector on the

powerhead with the receptacle on the body and

press together until they click into place.

Locked Brush

Roll Indicator

Power Switch

Top position is Off. Middle position is for floor cleaning and

cleaning with accessories (brush roll does not turn). Bottom

position is for cleaning carpets (brush roll turns).

2Locked Brush Roll Indicator

The brush roll indicator will illuminate brightly when the

brush roll motor has been locked up due to debris or some

other excessive loading of the brush roll. Slide the power

switch to the off position and check the brush roll area for

obstructions. After clearing the brush roll area, start the

vacuum and the brush roll will turn again.

CAUTION: Pulleys can be hot from normal use, to

avoid burns do not touch pulleys.

Cord Retainer

When preparing to use vacuum,

firmly push the electrical cord down

into the cord retainer. This will place

the electrical cord out of the way

while you vacuum.

HOW TO USE (continued)

Handle Collapse Button

To collapse the handle from the upright position,

press handle collapse button, rotate handle down.

Cord Storage Hooks

This unit has two convenient cord storage hooks

attached to the handle. Wind the cord around the

hooks and fasten the plug to the cord to prevent

unwinding.

Cord

Storage

Hooks

Handle

Collapse

Button

3Cord

Retainer

HOW TO USE ACCESSORIES

Collapse the handle from the upright position.

The dusting brush and upholstery nozzle fit on both the hose and the wand with

a built-in crevice tool.

Use the dusting brush to dust furniture, blinds, books, lamps,

and shelves.

The crevice tool cleans corners, base boards, between cushions.

Hose elbow rotates for easy use of the hose and

attachments.

To disconnect hose for inspection of blockages, align notch

on top of elbow with arrow on main body. Check for

blockages and clear if necessary. Align notch on top of

elbow with arrow on main body to reconnect.

Dusting Brush

Crevice

Tool

To Change Dust Cup Pleated Filter

NOTE: Turn off the switch and unplug the electrical cord before changing the

pleated filter. Never operate the vacuum cleaner without the dust cup or

the pleated filter.

HINT: When cleaning new carpet for the first time, cup will fill quickly. Check

often.

HOW TO MAINTAIN

The instructions given in this booklet serve as a guide to routine maintenance. To

avoid unnecessary service calls, check the dust cup, filter, belt, and brush roll often.

Empty the dust cup if it is full; clean the filter, replace the belt if it is stretched or

cracked, and clean the brush roll bristles if they are wrapped with thread and hair.

Remove the dust cup by pressing down on the

dust cup latch (a) and pulling dust cup away from

cleaner body. When replacing the dust cup put

bottom of dust cup in place by aligning tabs in

slots and pivot dust cup up against the cleaner

body. Lift up on dust cup latch to secure in place.

To Clean the Pleated Filter:

1. Remove dust cup from cleaner body. See above illustration (a).

2. Remove dust cup lid by grasping lid handles and lifting up.

3. To release the pleated filter from dust cup lid, press latch in the bottom lid handle.

Pull pleated filter away from dust cup lid.

4. To remove debris, tap filter against waste container or brush off. You may also

vacuum the filter using a different cleaner. If filter needs further cleaning, wash in

warm water using a mild detergent. To clean between filter pleats, fan open under

running water.

4. When all parts are completely dry, reattach pleated filter to dust cup lid and

follow the above steps in reverse to reassemble.

NOTE: Do not put any parts in a dishwasher.

NOTE: Your dust cup filter may need to be replaced if cleaning it does not restore

cleaning performance.

Check and clean the Pleated Filter once a

month to maintain good performance. The

filter can be cleaned by washing with mild

detergent and warm water. Be sure pleated

filter is completely dry before reinstalling.

HOW TO MAINTAIN (continued)

NOTE: Turn off the switch and unplug the electrical cord before servicing the

cleaner. Never operate the vacuum cleaner without the dust cup or filter.

How to Empty Dust Cup

FOR INSTRUCTIONS ON HOW TO REMOVE THE DUST CUP FROM THE

CLEANER BODY, REFER TO PAGE 8.

Emptying the Dust Cup:

It is clearly visible when the dust cup is full and needs emptying. Remove dust cup

from cleaner body. Remove dust cup lid from dust cup by grasping lid handles and

lifting up. (See below.) Then dump debris in a waste container.

Reinstalling the Dust Cup:

Grasp the dust cup lid by the lid handles and sit back on top of dust cup. It will fit only

one way. To replace the dust cup, put bottom of dust cup in place by aligning tabs in

slots and pivoting dust cup up against the cleaner body. Lift up on dust cup latch to

secure in place (a).

HOW TO MAINTAIN (continued)

CAUTION: Turn off the switch and unplug the electrical cord before servicing

the cleaner. Pulleys can be hot from normal use, to avoid burns do

not touch pulleys.

Remove the 11 screws on the

bottom of the power nozzle. Flip

the power nozzle back upright and

remove the hood.

Remove broken or worn brush roll

belt. Pinch new brush roll belt

together and position new belt so

teeth engage cog pulley on end of

motor shaft.

Place the other end of belt around

brush roll. Align left end of brush

roll into the base by rotating

slightly until brush roll end cap

slides into place.

Secure right end of brush roll into

base.

The brush roll belt is now installed.

Reinstall hood.

Replace Brush Roll Belt

2Cog

Pulley

Brush Roll

As the brush roll rotates, it sweeps and combs the carpet nap. Remove hair and threads

from the brush roll so it continues brushing the carpet nap. Check brush roll occasion-

ally for hair or string that may have wrapped around dowel. Remove with scissors.

When bristles have worn to about 1/4" in length, carpet cleaning effectiveness will be

reduced. It is time to replace the brush roll. Follow the instructions in the brush roll belt

section to open up the power nozzle and replace the brush roll.

Andere Handbücher für 410 SERIES

Inhaltsverzeichnis

Andere Eureka Staubsauger Handbücher

Eureka

Eureka 166DX - Boss Bagless Vacuum Bedienungsanleitung

Eureka

Eureka AS100-AS119 Series Bedienungsanleitung

Eureka

Eureka NES215A Bedienungsanleitung

Eureka

Eureka 5890 Series Bedienungsanleitung

Eureka

Eureka 4870 Series Bedienungsanleitung

Eureka

Eureka 8800 Series Bedienungsanleitung

Eureka

Eureka 160 Series Bedienungsanleitung

Eureka

Eureka 2970-2999 Series Bedienungsanleitung

Eureka

Eureka 3530 Series Bedienungsanleitung

Eureka

Eureka 470 Series Bedienungsanleitung

Eureka

Eureka NEU180 series Bedienungsanleitung

Eureka

Eureka 2500 Series Bedienungsanleitung

Eureka

Eureka NEC3MC Bedienungsanleitung

Eureka

Eureka 160 Series Bedienungsanleitung

Eureka

Eureka NEC 480 Series Bedienungsanleitung

Eureka

Eureka 5190 Series Bedienungsanleitung

Eureka

Eureka 8800-8849 Series Bedienungsanleitung

Eureka

Eureka FVM-5 Bedienungsanleitung

Eureka

Eureka 160 Series Bedienungsanleitung

Eureka

Eureka AS3001 series Bedienungsanleitung

Eureka

Eureka 4710 Series Bedienungsanleitung

Eureka

Eureka NEW200 Series Bedienungsanleitung

Eureka

Eureka 410 SERIES Bedienungsanleitung

Eureka

Eureka 8860-8899 Series Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch