EverFocus EHD150 Bedienungsanleitung

EVERFOCUS

1/3” B/W Rugged Dome Camera

Operation Instructions

Model No. EHD150

Please read this manual first for correct installation and operation. This manual should be retained

for future reference. The information in this manual was current when published. The

manufacturer reserves the right to revise and improve its products. All specifications are therefore

subject to change without notice.

PRECAUTIONS

1. Do not install the camera near electric or magnetic fields.

Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,

audio speakers since the magnetic fields generate from above devices will distort the video

images.

2. Never disassemble the camera nor put impurities in it.

Disassembly or impurities may result in trouble or fire.

3. Never face the camera toward the sun.

Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.

4. Keep the power cord away from water and liquid.

Touching the wet power cord may result in electric shock.

5. Never install the camera in areas exposed to water, oil or gas.

Water, oil or gas may result in failure, electric shock or fire.

6. Cleaning

Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from

the camera body. Use lens tissue or a cotton swab and ethanol to clean the sensor and the

camera lens.

7. Do not operate the camera beyond the specified temperature, humidity or

power source ratings.

Use the camera at temperatures within -46℃~ 50℃; -50.8°F~122°Fand humidity between

20%~ 80%. The input power source is 12VDC+/-10%, 24VAC+/-10%.

PREFACE

The most technically advanced EHD150 is the newest vandal-resistant B/W Rugged Dome

Camera from EverFocus Electronics. The B/W Rugged Dome Camera can withstand a blow

from a 10-pound sledgehammer and has a built-in heater that allows for operation in low

temperatures. It is perfect for all high-profile crime-prone applications such as building

entrances, retail stores, and shopping malls. The extremely EHD150 is unquestionably one

of the world's toughest cameras and is your best choice for vandal resistance.

FEATURES

zDesigned with advanced digital signal processing circuitry for high image quality.

zThe high sensitivity of 0.06 lux/F=1.6 is achieved by high –resolution 1/3” interline

transfer CCD.

zDC12V or AC24V switches automatically power supply; Line Lock for AC24V.

zS/N Ratio reaches 48 dB or more.

zBoth board lens and vari-focal lens (3.6 ~ 9mm, 9~22mm) are available.

zCompact size: 130(W) x 130 (D) x 98.9mm(H) / 5.2" (W) x 5.2" (D) x 3.95" (H)

zPolycarbonate base withstand the impact of a 10 pounds sledgehammer, smoke color

or clear as option.

zUnique security screw locked

zOperating temperature –46 ~ +50 deg Celsius.

zHeater triggered when temperature less than 10 deg Celsius.

INSTALLATION

1. Loosen the 4 fix screws on the housing cover by using the attached wrench (Figure 1).

Carefully uncap the housing cover as the direction shown below (Figure 2), please pay attention

not to damage the lens. To remove the housing cover, push the hinges to the bottom of the

bracket, the hinges can be easily removed from the bracket.

2. Remove the camera.

To remove the camera, first unplug the wire connection on the back of the camera.

Then loosen the 2 locking screws on the camera base, push the camera base to the right

(toward heater direction, as shown in Figure 3), remove the camera from the mounting

base. Reinstall the camera and the cable while the base mounting is completed.

Locking Screws

Board Lens

Vari-Focal Lens

Heater

Figure 1 Figure 2

Figure 3

3. Mounting the base.

Attach the base to the wall or ceiling, fix the base by the 4 setscrews attached in the

accessory pack. The dome is weighted 1.7kg, please make sure if the mounting is

strengthened enough to support it, if not, please reinforce the mounting according to the

environment.

Note: The diameter of the screw hole isψ4.7mm.

Caution: To prevent moisture leaking into the housing, apply an appropriate gasket

Conduit plug setscrew

Side conduit entry

Back conduit entry

Mounting Setscrew

The camera comes with a conduit plug

pre-installed in the PF 1/2 conduit entry on the

side. The screw can be removed and installed in

the back conduit entry. Loosen the conduit plug

setscrew (as shown in Figure 5) before

removing the conduit plug.

Side conduit entry (PF1/2)

Conduit plug

Back conduit entry (PF1/2)

Figure 4

Figure 5

or sealant around the conduit connection.

4. Re-assemble Camera

1. If mounting COLOR RUGGED DOME CAMERA on the wall, please to aim

the “Wall” in line with the triangle “S” marked on the lead frame. (factory

default)

2. If mounting COLOR RUGGED DOME CAMERA on the ceiling, please to

aim the “Ceiling” in line with the triangle “S” marked on the lead frame.

Figure 6-2

Figure 6-1

“Wall”

“Ceiling”

5. Wire Connection

Connect the power supply cable (AC24V/DC12V), video output and alarm output to

the proper connectors shown as Figure 7.

The V. Phase adjustment screw is located on the termination board. The vertical phase

may require adjustment to synchronize the vertical phase of the camera with other

camera in the system when it is to be used in the line-lock sync mode. Make the

adjustment when the vertical phase of the camera does not match with other cameras.

Termination Board

Video

Alarm COM

Micro Switch for Alarm trigger

GND

Alarm NO Alarm NC

Power In

DC12V (+) or AC24V

V. Phase Adjustment VR

Figure 7

Power In

AC12V (-) or AC24V

6. View Angel Adjustment

The camera can be rotated 360∘horizontally, 140°vertical and 60° 3’rd axis view

angles (as shown in Figure 8). Adjust the proper camera view angel as needed. If

a vari-focal lens is used, you may adjust the focus and zoom of the lens to bring the

object in focus. Be sure to loosen the locking screws on the lens before you do the

adjustments.

Figure 8

Lens fixing Screws

DIPSWITCH FUNCTION

LL(Line-Lock) Off/On

To select the sync mode between Internal Sync.(LL off) and Line-Lock (LL on).

Set the line-lock off, the camera will synchronize to the internal time base. Set the

line-lock on, the camera’s vertical synchronization can be driven by the AC signal in the

power lines.

Note: Line-Lock sync mode operation is possible only when used with an AC power

source; it’s not possible with a DC power source.

The default setting is ON.

AGC (Automatic Gain Control) Off/On

AGC ON: The sensitivity increases automatically when light is low.

AGC OFF: A-low-noise picture is obtained under a low light condition.

The default setting is ON.

OFF

AGC

BLC

Video

GND

OFF

AGC

BLC

Video

GND

ALC

LEVEL

Board Lens Vari-Focal Lens

BLC (Back Light Compensation) On/Off

When BLC is turned on, the AGC, ES and IRIS operating point is determined by

averaging over the center area instead of entire field-of-view, so that a dimly-lit

foreground object at center area can be clearly distinguished from brightly-lit

backgrounds.

BLC should not be used unless it is needed to compensate for back-lit.

The default setting is Off.

FL (Flickerless Function) On/Off

When picture flicker fiercely, turn FL on, then the camera will stabilize the speed of

electronic shutter at 1/100(NTSC) or 1/120(PAL) automatically, and reduce the flicker

immediately.

The default setting is Off.

ES (Electronic Shutter) Off/On

ES ON: The camera continuously adjusts the shutter speed from 1/60 (NTSC), 1/50

(PAL) second to 1/100,000 second according to the luminance conditions of the scene.

ES OFF: The shutter speed is fixed at 1/60 (NTSC), 1/50 (PAL) second.

Set ES OFF, when auto iris lens is used or flicker is observed under a very bright

fluorescent lamp. Otherwise, turn ES on for optimum performance. The default setting

is ON.

SPECIFICATIONS

Pickup Device 1/3” SONY interline transfer CCD

Picture Element NTSC :768(H) × 494(V)

PAL: 752(H)×582(V)

Horizontal Resolution 560 TV lines

Sensitivity 0.06 lux / F=1.6

S/N Ratio Over 48dB(AGC off)

Weatherproof Ratings IP66

Electronic Shutter 1/60(1/50)~1/100,000 (Board lens only)

IRIS Control Auto (vari-focal lens only)

Auto Gain Control On/Off switch

Back Light Comp. On/Off switch

Line Lock On/Off switch for 24VAC

Gamma Correction 0.45

Video Output 1.0Vp-p,75ohm

Power Source 12VDC+/-10%, 24VAC+/-10%

Power Consumption 5W Max. (15W when heater active; thermostatically controlled)

Sync. Mode Internal Sync. /Line lock (Only AC24V)

Dimensions 130 (W) x 130 (D) x 98.9 (H) mm / 5.2" (W) x 5.2" (D) x 3.95" (H)

Lens Board lens f=3.6, F=2.0

Vari-focal f=3.6~9mm, F=1.6

Vari-focal f=9~22mm, F=1.6

*Lens models and availability vary in different regions

Heater Auto Activated

Temperature

10℃, Heater optional

Operating Temperature -46℃~ 50℃; -50.8°F~122°F( 20% ~ 80% humidity)

Weight 1.7kg ; 3.7 lbs

Certifications FCC/CE

Andere Handbücher für EHD150

Inhaltsverzeichnis

Andere EverFocus Sicherheitskamera Handbücher

EverFocus

EverFocus M117-N701-001 Bedienungsanleitung

EverFocus

EverFocus EQ610 Bedienungsanleitung

EverFocus

EverFocus NeVio EAN900 Bedienungsanleitung

EverFocus

EverFocus EBH5102 Bedienungsanleitung

EverFocus

EverFocus ED120 Series Bedienungsanleitung

EverFocus

EverFocus ED700W Bedienungsanleitung

EverFocus

EverFocus EBA2880 Bedienungsanleitung

EverFocus

EverFocus eZ.HD Series Bedienungsanleitung

EverFocus

EverFocus EZN Series Bedienungsanleitung

EverFocus

EverFocus M116-EZ700-001 Bedienungsanleitung

EverFocus

EverFocus EDH5201 Bedienungsanleitung

EverFocus

EverFocus EMN Series Bedienungsanleitung

EverFocus

EverFocus EHD930F eZ.HD Series Bedienungsanleitung

EverFocus

EverFocus EMD335 Bedienungsanleitung

EverFocus

EverFocus Speed Dome EPTZ1000 Bedienungsanleitung

EverFocus

EverFocus EMN2260 Bedienungsanleitung

EverFocus

EverFocus EHD320 Bedienungsanleitung

EverFocus

EverFocus H.265 VANGUARD II Series Bedienungsanleitung

EverFocus

EverFocus EQ500 Bedienungsanleitung

EverFocus

EverFocus M105-DE100-002 Bedienungsanleitung

EverFocus

EverFocus H.265 VANGUARD II Series Bedienungsanleitung

EverFocus

EverFocus EPTZ3150 Bedienungsanleitung

EverFocus

EverFocus M122-EJ230-002 Bedienungsanleitung

EverFocus

EverFocus Eq250 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung