Extech Instruments ExStik RE300 Bedienungsanleitung

User Guide

ExStikTM Model RE300

Waterproof ORP Meter

RE300-en-GB_V4.5 8/16

ExStikTM Description

Front Panel Controls

1. Battery compartment cap

2. LCD Display

3. MODE button

4. CAL button (unused on RE300)

5. ON/OFF button

6. Electrode collar

7. Electrode

(Electrode cap is not shown)

Display Description

1. Reading

2. Units

3. Bargraph

4. Data Hold

5. Scale

6. Low Battery

RE300-en-GB_V4.5 8/16

Operation

Getting Started

Battery Activation: An insulating tab is located in the battery compartment and prevents battery drain

during storage. It must be removed before use.

White KCL crystals may be present on the electrode. These crystals will dissolve in a distilled water

soak or they can be simply rinsed with tap water.

Do NOT wipe the end of the RE300 electrode as it may damage the sensor.

When the RE300 is turned on, it enters the Automatic Calibration mode. ‘SELF’ and ‘CAL’ will appear

on the LCD while calibration is in progress. After the calibration is complete, ‘SELF’ and ‘CAL’ will

extinguish and both the main display and bargraph will read ORP in mV units. The bargraph will read

0mV (far left), 500mV (center), and 1000mV (far right).

ORP Testing

1. Remove cap from the electrode and soak the electrode in distilled or tap water for 10 minutes.

2. Press the ON/OFF button to switch the RE300 on.

3. Dip the electrode1/2” to 1” into the test solution. Stir once and let the reading stabilize for 1 to 3

minutes.

4. Note the ORP or press MODE to freeze the reading The HOLD display icon will appear along

with the held reading. The held reading will be stored in the next 15-reading storage location

(see below). Press the MODE key to return to normal operation.

5. Press the ON/OFF button to turn the RE300 off. If you do not press a button for 10 minutes the

RE300 shuts off automatically.

15-Reading Measurement Storage

1. Press the MODE button to store a reading. The LCD will briefly display the memory location

number and then the value stored (Data Hold will activate).

2. Press MODE again to return to normal operation.

Repeat step 1 above to store the next reading and so

on.

3. If an attempt is made to store more than 15 readings,

the stored readings (starting with the first reading) will

be overwritten.

Recalling Stored Readings

Note: First ensure that the HOLD symbol is not displayed. If it is, exit the HOLD function by pressing

the MODE button.

1. Press the CAL button once and then press the MODE button immediately after CAL is

displayed; the location number (1 through 15) will flash. If the CAL mode is accidentally

accessed (display flashing), press the CAL button again to exit.

2. The last stored reading taken will be displayed first. To advance through the stored readings,

press the MODE button. The location number is displayed first, followed by the reading stored

in that location.

3. To exit the storage mode, press the CAL button and the ExStikTM will return to normal

operation.

RE300-en-GB_V4.5 8/16

Measurement and Display Considerations

If the unit appears to be locked (display frozen). It is possible that the Data Hold mode has

been inadvertently accessed by pressing the MODE button. Simply press the MODE button

again or turn the meter off and restart if the display appears frozen.

If the meter does latch up and no button presses revive it, remove the batteries and restart.

Note that if the batteries are removed, any stored readings will be discarded. Factory

calibration data for all models will be retained, however.

Replacing the Electrode

To preserve Electrode life, keep the sponge in the protective cap soaked with

distilled or tap water when not in use (store vertically).

DO NOT USE DE-IONIZED WATER.

1. To remove an electrode, unscrew and completely remove the electrode collar (turn the collar

counter-clockwise to remove).

2. Gently rock the electrode from side to side, pulling it downwards, until it disconnects from the

meter.

3. To attach an electrode, carefully plug the electrode into the meter socket (note that the

electrode connector is keyed, ensuring proper connection).

4. Tighten the electrode collar firmly enough to make a good seal (a rubber gasket seals the

electrode with the meter).

Powering the ExStik™

The ExStikTM uses four (4) CR2032 batteries (included). If the batteries are weak, the ‘BAT’

indicator appears on the LCD. Press the ON/OFF key to turn the ExStikTM on or off. The auto

power off feature shuts the ExStikTM off automatically after 10 minutes of inactivity to preserve

battery life.

Accuracy check of the RE300 electrode

1. Remove cap from the electrode and press the ON/OFF button to switch the RE300 on.

2. Dip the electrode1/2” to 1” into the ORP Standard test solution. Stir once and let the reading

stabilize for 1 to 3 minutes.

3. The measurement should be within +/- 4mV of the ORP Standard.

RE300-en-GB_V4.5 8/16

Battery Replacement

1. Twist off the battery compartment cap

2. Replace the four (4) 2032 batteries observing polarity.

3. Replace the battery compartment cap



Neverdisposeofusedbatteriesorrechargeablebatteriesinhouseholdwaste.

Asconsumers,usersarelegallyrequiredtotakeusedbatteriestoappropriate

collectionsites,theretailstorewherethebatterieswerepurchased,orwherever

batteriesaresold.

Disposal:Donotdisposeofthisinstrumentinhouseholdwaste.Theuserisobligatedtotakeend‐

of‐lifedevicestoadesignatedcollectionpointforthedisposalofelectricalandelectronic

equipment.

Optional Accessories

Replacement ORP electrode (Part Number: RE305)

Specifications

Display Multifunction LCD with Bargraph

Operating conditions 0 to 50oC (32 to 122oF) / < 80% RH

RP Range / Accuracy ± 999mV / ± 4mV

Electrode Platinum with silver wire in KCL

Electrode Compensation 204.6mV

Measurement storage 15 tagged (numbered) readings

Power Four (4) CR2032 button batteries

Low battery indication ‘BAT’ appears on the LCD

Auto power off After 10 minutes of inactivity

Dimensions 35,6x172,7x40,6mm (1,4x6,8x1,6”); 110g (3,85oz)



Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

ISO‐9001Certified

www.extech.com

Inhaltsverzeichnis

Andere Extech Instruments Messgerät Handbücher

Extech Instruments

Extech Instruments 480836 Bedienungsanleitung

Extech Instruments

Extech Instruments 451112 Bedienungsanleitung

Extech Instruments

Extech Instruments MA61 Bedienungsanleitung

Extech Instruments

Extech Instruments 407119-NIST Bedienungsanleitung

Extech Instruments

Extech Instruments EasyView EA30 Bedienungsanleitung

Extech Instruments

Extech Instruments MA1500 Bedienungsanleitung

Extech Instruments

Extech Instruments 475055 Bedienungsanleitung

Extech Instruments

Extech Instruments 475055 Bedienungsanleitung

Extech Instruments

Extech Instruments MO297 Bedienungsanleitung

Extech Instruments

Extech Instruments MO270 Bedienungsanleitung

Extech Instruments

Extech Instruments PH220A Bedienungsanleitung

Extech Instruments

Extech Instruments 461995 Bedienungsanleitung

Extech Instruments

Extech Instruments MO220 Bedienungsanleitung

Extech Instruments

Extech Instruments 407113 Bedienungsanleitung

Extech Instruments

Extech Instruments EX613 Bedienungsanleitung

Extech Instruments

Extech Instruments FM300 Bedienungsanleitung

Extech Instruments

Extech Instruments MO55 Bedienungsanleitung

Extech Instruments

Extech Instruments DO210 Bedienungsanleitung

Extech Instruments

Extech Instruments AN300 Bedienungsanleitung

Extech Instruments

Extech Instruments CG206 Bedienungsanleitung

Extech Instruments

Extech Instruments EasyView EA31 Bedienungsanleitung

Extech Instruments

Extech Instruments 381235 Bedienungsanleitung

Extech Instruments

Extech Instruments CO260 Bedienungsanleitung

Extech Instruments

Extech Instruments SDL300 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung