Extron electronics Annotator 300 Bedienungsanleitung

Installation

Mounting and Cabling

Step 1 — Mounting

a. Turn off or disconnect all equipment power sources.

b. Mount the Annotator 300 to a rack using the pre-installed rack ears (see

gure 1), or use an optional MBU 149 mounting kit (part number 70-222-01)

for under-the-desk mounting (see gure 2).

Step 2 —Connecting inputs

a. Connect analog video sources to the universal connector (see Babove).

Compatible sources are RGB, YUV (HD or SD), RGBcvS, S-video and

composite video. Default setting for the input is auto-detect.

b. Connect a digital HDMI or DVI source to the HDMI connector (see Cabove).

c. Connect a DisplayPort input source to the DisplayPort connector (see D

above).

Step 3 —Connecting outputs

a. Connect suitable video displays to the two HDMI connectors (see Eabove).

b. Connect either an Extron DTP device to this connector for transmission over

DTP (default), or connect an HDBaseT device if transmitting over HDBaseT

(see Fabove). Set the DIP switch to DTP or HDBaseT as applicable.

CAUTION: Risk of damage to equipment.

DO NOT connect an HDBaseT unit if using DTP transmission.

The power carried over DTP may damage the unit.

Attention: Cela risque d'endommager votre équipement.

Ne PAS connecter une unité HDBaseT si vous utilisez la transmission

DTP. L'alimentation transmise sur DTP peut endommager l'unité.

Annotator 300 • Setup Guide

The Extron Annotator 300 Annotation Graphics Processor is a scaling product that allows a presenter to draw, point, or type on video or

computer source outputs using a touch panel, mouse, or keyboard.

This set up guide allows you to easily and quickly set up and congure your Annotator 300 using step by step instructions. It covers

performing basic operations using the front panel controls and selected Simple Instruction Set (SIS™) commands.

NOTE: For full installation, configuration, menus, and operation details, see the Annotator 300 User Guide at www.extron.com.

Rack Ears

50/60 Hz

100-240VAC --A MAX

OVER DTP

DTP

HDBT

REMOTEOUTPUTS

INPUTS

RS-232 IR

1 1UNIVERSAL HDMI DISPLAYPORT23 HDMI 2A HDMI 2B

Tx Rx GTxRx

CONTACT

LAN

RESET

USB 1

RS-232

Tx Rx G

SIG

DTP OUT

LINK

ADEF

GHIJK

Power and video input connections Outputs and control connections

AAC power connector

BUniversal analog 15-pin HD connector

CHDMI connector (HDMI/DVI inputs)

DDisplayPort connector

EHDMI connectors (2) (HDMI/DVI outputs)

FRJ-45 connector (DTP or HDBaseT

output), selectable by DIP switch

G5-pole captive screw connector

(for DTP RS-232 and IR insert)

HUSB A connectors (2)

IReset button and LED

JRJ-45 LAN connector

KRemote RS-232 3-pole captive

screw connector

LRemote contact closure 3-pole

captive screw connector

Rear Panel Features

#8 Screw

(4) Places

Each Side

MBU 149

Mounting Bracket

Mounting Screws

(2) Places

Each Side

Figure 1. Rack Mount

Figure 2. Furniture Mount

Annotator 300 • Setup Guide (Continued)

Step 4 —Connecting control devices

a. For RS-232 or IR control over DTP, connect to the 5-pole "Over DTP" captive screw connector (see Gon page 1).

b. For control through Ethernet, connect a LAN or WAN to the RJ-45 connector (see Jon page 1). The default IP address is

192.168.254.254. The default subnet mask is 255.255.0.0.

c. For serial RS-232 control, connect a host device to the 3-pole captive screw connector (see Kon page 1).

The default baud rate is 9600.

d. For remote contact closure control, connect a host device to the 3-pole captive screw connector (see Ion page 1).

e. For control through USB, connect a host device to the front panel mini USB port (see Aon image below).

Step 5 —Connecting user interface devices and touch panels

Connect user interface devices (mouse and keyboard) or touch panels to the Annotator 300 using either of the rear panel USB ports (see

Hon page 1). Alternatively the front panel USB port can also be used to connect a user interface device.

Step 6 —Connecting power

Plug in a standard IEC power cord from a 100 to 240 VAC, 50-60 Hz power source into this power receptacle (see aon page 1).

Enabling or Disabling Executive Mode 2 From the Front Panel

To enable Executive mode 2 or 0, press and hold the Menu and Next buttons simultaneously for 2 seconds. The display indicates that

Executive mode is either enabled or disabled. When the Annotator 300 is in Executive mode 0 (unlocked), this selects mode 2 (locked)

and if in Executive mode 2, this selects mode 0 (unlocked).

When either Executive mode (1 or 2) is enabled and a front panel action is attempted (other than input switching and Auto-Image), the

LCD displays the status for 2 seconds. Executive mode 1 can be enabled or disabled only by SIS commands.

Front Panel Overview

USB

CAPTURE

RECALL

INPUTS

123

AUTO

IMAGE ADJUST

CONFIG

ANNOTATOR 300

ANNOTATION GRAPHICS PROCESSOR

ADEFGH

AFront panel mini USB conﬁguration port — Connect a control system or computer to this mini USB port (cable not supplied),

for device conguration, control, and rmware upgrading.

BFront panel USB port — Connect an external drive to store or recall captured images, or connect a user

interface device.

CCapture and Recall Buttons — Use these buttons to capture or recall captured images to or from a connected external drive,

network drive, or internal memory.

DInput selection buttons and LEDs (1-3) — Select/switch inputs; LEDs indicate which input is active (current input lights green).

EAuto Image Button — Pressing this twice initiates the Auto-Image™function on the selected input.

FLCD display — This 16x2 screen displays device settings and menu conguration information.

GMenu navigation buttons (Menu, Next) — These buttons allow navigation through the LCD menu system of the Annotator 300.

HAdjust knobs — These are used with the menu navigation buttons to adjust the device settings and picture controls.

Setting the Front Panel Locks (Executive Modes)

The Annotator 300 has three modes of front panel security lock that limit the operation of the unit from the front panel.

Executive mode 0 (disabled) — The front panel is fully unlocked. This is the default setting.

Executive mode 2 (enabled) — The front panel is locked except for input switching. Can be set via front panel or by SIS command.

Executive mode 1 (enabled) — The front panel is completely locked and can be enabled and disabled only by SIS commands.

See the online Annotator 300 User Guide for SIS commands.

Configuring the Annotator 300

The Annotator 300 can be congured either via front panel menus or through a host connected via RS-232, USB, or LAN connection.

Through a host connection, the Annotator 300 can be congured using Extron Product Conguration Software (PCS), embedded

webpages or by using Extron Simple Instruction Set (SIS) commands.

Front Panel Menu System

The scaler has a menu system consisting of six submenus

that can be accessed using the front panel Menu and Enter

buttons. The Communications menu (View Comm Settings)

is a read-only menu. The menus are:

• User Presets • Picture Controls • Input Conﬁguration • Output Conﬁguration • Advanced Conﬁguration • Communication Settings

To use any menu, press the Menu button to access the Main menu, then repeatedly press the Menu button to cycle through the list

to the desired menu. Press Next to enter the desired submenu, and follow the steps below.

NOTE: Press Menu at any time to exit a submenu and return to the main menu.

For detailed information on the menus, see the Annotator 300 User Guide,available online at www.extron.com.

Congure the outputs, then the inputs, as follows:

1. Within the Output Conguration menu, use either Adjust knob to congure the output rate and resolution, the HDMI format, and to

set the HDCP Notication (Off or On).

2. From the Advanced Conguration menu, Test Pattern submenu, select the Alternating Pixels (Alt. Pixels) test pattern and view the

display to conrm the display is sampling the signal properly.

3. From the Test Pattern menu, change the test pattern to Crop, and adjust the display size, position, or overscan settings until all four

sides of the crop pattern are visible.

4. Use the Advanced Conguration menu to set the Aspect ratio (Fill or Follow). Rotate either Adjust knob to the desired setting.

5. Within the Input Conguration menu, press the applicable input button, then press Next to cycle to the desired submenu. Rotate the

Adjust knobs to change the input values (for example, Input type, Film detection, and so on) as required. Use this menu to make any

desired advanced adjustments including Horizontal and Vertical Start, Pixel Phase, Total Pixels, Active Pixels, and Active Lines;

OR...

6. Perform Auto-Image. Auto-Image is a quick way to size an input to t the output. To perform Auto-Image on an input, press the Auto

Image button. Press it again to conrm.

7. Use the Advanced Conguration menu to change image transition effect. Rotate either Adjust knob to select cut or fade.

Touch Panel Conﬁguration

If a USB touchpanel is part of the system,conrm the panel is supported by the rmware on the Annotator 300 by reviewing the

compatibility list available on the product page of the Extron website (www.extron.com). If the touchpanel is not supported by the

rmware, a supporting module must be uploaded to the Annotator 300 using PCS 2.1.

1. Connect to the Annotator 300 using the PCS 2.1 software.

2. From the icon ribbon, click on and open the Annotation Settings page.

3. In the Installed USB Modules section, click Add. The Add a USB Device window opens.

4. Find the touchpanel device in the list of available modules, or if the device is not present in the list but is available from the Extron

website, click on Check for Updates.

5. Select the module that supports your touchpanel and click Add. The window closes and the selected

touchpanel is now listed in the Installed USB Modules section. 1

Touch to Start

Touch Panel Calibration

If a touchpanel screen is attached to the Annotator 300, the touch accuracy can be calibrated using the

Calibrate Panels setting in the Advanced conguration menu.

1. Within the Advanced Conguration menu select Yes and press Next to cycle to Calibrate Panels.

2. Observe all connected touchpanel screens. On all screens a green box appears at top center.

To start the sequence, tap the box on one of the panel screens you need to calibrate.

3. The box disappears and a crosshatch +appears in the upper left corner. Tap the screen at the crosshatch.

4. The crosshatch re-appears at the top right corner. Tap the crosshatch. The crosshatch re-appears in the lower right.

5. Repeat by tapping the crosshatch as it reappears in each corner, in sequence (see image at above right) and then tap the crosshatch

when it appears in the center of the screen.

6. After tapping the fth (central) crosshatch, the unit saves the calibration data and restarts the sequence by showing the green box

on all connected touchpanels.

7. Repeat for each connected touchpanel screen. Press any front panel button to exit the sequence and save the data.

Annotation Graphics Overview

The Annotator 300 output includes a graphical toolbar, which is used for annotation. The toolbar slides in from the right side, and can be

accessed through a touch screen, or by using a compatible 2-button mouse attached to a USB port.

To open the toolbar, click on the green arrow at top right of the screen. The menu bar slides into view and, when enabled, the toolbar

stays visible down the right side of the display and allows for selection of various tools and controls. See page 4 for details.

To close the toolbar, click on the arrow again or allow it to time-out.

NOTE: By default, the toolbar closes after 10 seconds of inactivity. This duration can be modified using SIS commands.

User

Presets

Menu Menu

Output

Configuration

Exit Menu

Press NEXT

View Comm

Settings

Advanced

Configuration

Input

Configuration

Picture

Controls

Power and video input connections Outputs and control connections

AAC power connector

BUniversal analog 15-pin HD connector

CHDMI connector (HDMI/DVI inputs)

DDisplayPort connector

EHDMI connectors (2) (HDMI/DVI outputs)

FRJ-45 connector (DTP or HDBaseT

output), selectable by DIP switch

G5-pole captive screw connector

(for DTP RS-232 and IR insert)

HUSB A connectors (2)

IReset button and LED

JRJ-45 LAN connector

KRemote RS-232 3-pole captive

screw connector

LRemote contact closure 3-pole

captive screw connector

Input Selection — This opens a pop-up palette

displaying the selectable inputs. Selecting an input

button switches the display to that input.

Fill — Select this when selecting rectangle or ellipse,

to draw a solid shape filled with the selected color.

Pointer — This changes the cursor to an extra large

arrow of the currently selected color.

Undo — This undoes the last 15 completed annotations or

a Clear action.

Auto Image — When selected, the unit performs an

Auto-Image on the currently selected input.

Redo — If selected while using the Undo function, it

recreates the last undone annotation.

Freehand — This allows freehand drawing on the

display.

Clear — This clears the screen of all unsaved annotations.

This action can be undone with the Undo function.

Line — This creates a straight line between two points.

Tools — This opens a secondary palette with advanced

tools: Capture, Freeze, Mute, Whiteboard, Spotlight, Zoom,

and Pan.

Arrow — This creates a straight line with an arrowhead.

Capture — This takes a snapshot image of the current

program output, including annotations. Captured images

can be saved to the unit or PC.

Rectangle — This creates a rectangle with edges

parallel to the raster.

Freeze — This freezes the live video. Re-select to unfreeze

the video, or alternatively, switch inputs.

Ellipse — This creates an ellipse between the primary

and the opposite corner.

Mute — This mutes the video input and displays a black

screen. Annotations and menus are still visible. Re-select

to unmute.

Text — This creates on-screen text at any point

selected. Press the <Enter> key to commit the text to

the screen.

Whiteboard — This creates a white screen for annotations.

Re-select to disable the whiteboard.

Highlighter — This creates a semi-transparent line

allowing the video to show through.

Spotlight — This creates a no-fill ellipse to focus on a

specific area of the screen, while the brightness of the

outer area is greatly reduced.

Size Select — This adjusts size of the annotation tool,

such as text size, after selecting the Text tool.

Zoom — This zooms in on a specific area of the screen.

Using the cursor, create a rectangle at that area. Create a

rectangle of less than 100 pixels to reset zoom to default.

Eraser — This erases any (unsaved) annotations on the

screen. The size is defined by the size tool.

Pan — Select this while an image is zoomed in, to

move the focus to a new area. Place the cursor on a

zoomed image and drag to the new area.

Color — This allows up to 16 colors to be selected for

any drawing function (fill or outline), text, or pointer.

Basic SIS Commands Table

The Annotator 300 can be congured with specic SIS commands via USB, RS-232, or a LAN connection. This table lists a selection of

the commands. For a full list of SIS commands see the Annotator 300 User Guide, online at www.extron.com.

Command ASCII command

(host to annotator)

Response

(annotator to host)

Additional description

Select input X!! InX!]Select video from input X!.

Execute Auto-Image A Img0]Execute an Auto-Image.

Mute video to black X#*1B VmtX#*1]Mute X# video and display to a black screen.

Unmute video X#*0B VmtX#*0]Unmute video mute.

Freeze input 1F Frz1]Freeze selected input.

Unfreeze input 0F Frz0]Unfreeze selected input.

Show/hide annotations EX#Ashw}Ashw X#] Set output(s) to display the annotations.

Show/hide cursor EX#Cshw}Cshw X#] Set output(s) to display the cursor.

Show/hide OSD menu EX#Mshw}Mshw X#] Set output(s) to display the OSD menu.

Clear all annotations E0Edit}Edit0]Clears all annotations on the output (can be undone).

NOTE: X! = Input number: 1, 2, or 3

X# = Output group selections: 0 = All (default), 1 = Output 1 only (HDMI), 2 = Output 2A and 2B only (HDMI and DTP), 3 = None

Extron USA Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517

Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001

Annotator 300 • Setup Guide (Continued)

68-2378-50

Rev. A

04 14

Andere Handbücher für Annotator 300

Inhaltsverzeichnis

Andere Extron electronics Computerhardware Handbücher

Extron electronics

Extron electronics UCS 601 Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T/R 301 Bedienungsanleitung

Extron electronics

Extron electronics IPCP Pro PCS1 xi Bedienungsanleitung

Extron electronics

Extron electronics AXP 64 C AT Bedienungsanleitung

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Bedienungsanleitung

Extron electronics

Extron electronics Quantum Ultra Bedienungsanleitung

Extron electronics

Extron electronics Annotator 300 Bedienungsanleitung

Extron electronics

Extron electronics StudioStation 100 Bedienungsanleitung

Extron electronics

Extron electronics IPCP Pro Series Bedienungsanleitung

Extron electronics

Extron electronics AXP 64 C AT Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 202 Bedienungsanleitung

Extron electronics

Extron electronics WindoWall Pro Series Bedienungsanleitung

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Bedienungsanleitung

Extron electronics

Extron electronics IPL Pro S1 Bedienungsanleitung

Extron electronics

Extron electronics Annotator Bedienungsanleitung

Extron electronics

Extron electronics Annotator 300 Bedienungsanleitung

Extron electronics

Extron electronics StudioStation 100 Bedienungsanleitung

Extron electronics

Extron electronics Dual Window Multi-Graphic Processor MGP 462 Bedienungsanleitung

Extron electronics

Extron electronics Quantum Ultra Series Bedienungsanleitung

Extron electronics

Extron electronics Annotator 401 Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 202 Bedienungsanleitung

Extron electronics

Extron electronics DMP 64 Plus Bedienungsanleitung

Extron electronics

Extron electronics Scalable Multi-Graphic Videowall Processors MGP 464W... Bedienungsanleitung

Extron electronics

Extron electronics IPL Pro Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung