Extron electronics DMP 64 Plus Bedienungsanleitung

DMP 64 Plus • Setup Guide

This guide provides basic instructions for an experienced technician to install the DMP 64 Plus ProDSP™Digital Matrix Processor.

For more information, specications, and the user guide, see the DMP 64 Plus product page on www.extron.com.

Disconnect Power and Mount the DMP 64 Plus

Disconnect power from the DMP 64 Plus and turn off all devices that will be connected to it. The DMP 64 Plus is housed in a

half rack width, 9.5 inch deep, 1U high metal enclosure that can be rack mounted or placed on a table with the provided rubber

feet. Select a suitable mounting location, then choose an appropriate mounting option. Mounting information can be found in the

DMP64 Plus User Guide on www.extron.com.

Make all external device connections before applying power.

Rear Panel Connections

INPUTS

I/O

OUTS

DMP EXP

ACP

REMOTE

USB AUD

LAN/VoIP

1 2 C V AT

1 (PRI) PoE+ 2 (SEC)

RS-232

Tx+V

IN G O IN G O IN G O IN G O IN G O IN G O

+S -S Rx GG

1 2 3 4 5 6 1 2 3 4

POWER

12V

2.0A MAX

1 2 3 4 5 6

A B C D E F G H

IJ K

Figure 1. DMP 64 Plus C V AT Rear Panel

APower Input — Connect the included external 2-pole captive screw power supply.

BEXP Port — Connect an EXP-enabled device to this RJ-45 port for a digital audio connection using Extron proprietary

protocol. Use the included one foot long shielded CAT 6 cable to connect two EXP-enabled devices to form a larger matrix

system. The expansion bus supports 16 bidirectional channels of audio (see the DMP 64 Plus User Guide for EXP bus

operation details).

CAT Ports (AT models only) — Two RJ-45 ports form a Gigabit switch that interfaces with the AT bus. The AT expansion bus

uses Dante®protocol for digital audio networking and allows DMP 64 Plus AT models to connect with other Dante-enabled

devices to form a larger matrix (see the DMP 64 Plus User Guide for operation details).

NOTE: Dante Controller software is required to configure the AT expansion bus. Dante Controller is available at

www.extron.com (see the DMP 64 Plus User Guide for instructions on installation and operation).

DACP Panel Port — Use a 4-pole 3.5 mm captive screw connector to connect an ACP

control device for configuration via DSP Configurator (wiring shown to the right).

ERS-232 Port — Use a 3.5 mm 3-pole captive screw connector to connect the host

RS-232 cable for bidirectional RS-232 (±5V) serial control (wiring shown to the right).

The default baud rate is 38400.

FLAN Ports — One RJ-45 port (non-V models) or two RJ-45 ports (V models) are

available for control network traffic (all models) and VoIP network traffic (V models

only). On DMP 64 Plus V models, the LAN/VoIP ports have multiple configuration options (refer to the DMP 64 Plus User

Guide for configuration options). On the Vmodels, by default, both control and VoIP traffic are transported on LAN/VoIP 1.

Port Default IP Address Default Subnet Mask Default Gateway Default DHCP

LAN 1 192.168.254.254 255.255.255.0 0.0.0.0 OFF

LAN 2 (V models only) 192.168.1.254 255.255.255.0 0.0.0.0 OFF

GUSB Audio Port — Connect a Windows or Mac computer to this USB mini-B port to interface with the DMP 64 Plus as a 4x4

USB audio device (see the DMP 64 Plus User Guide for additional USB audio interfacing capabilities).

Ground

+Signal

Signal

+12 VDC

RS-232

Tx Rx G

REMOTE

Transmit

Receive

Ground

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

HReset Button and LED — The reset button returns the DMP 64 Plus to different tiers of default states. When using the reset

function, the LED blinks to signify the different reset modes. When not using the reset function, the LED operates as a power

indicator and matches the front panel power LED (see the Reset Modes section of the DMP 64 Plus User Guide for more

information on the different reset modes).

IMic/Line Inputs — Use 6-pole 3.5 mm captive screw connectors to connect 6 balanced or unbalanced microphone or mono

line level sources (see 6-pole Audio Input Wiring below). Inputs 1 through 6 provide phantom power and AEC.

Tip

Slee

Ring

Tip

Slee

Ring

Tip

Sleeve

Tip

Sleeve

6-pole Audio INPUT Wiring

Balanced Input Unbalanced Input

Jumper

Figure 2. 6-pole Audio Input Wiring

NOTES:

• Balanced or unbalanced stereo sources can be connected to the 6-pole inputs.

• When using the 5-pole CSR adapter, connect it so the far left plug is inserted into the far left jack of the 6-pole

input.

JDigital I/O Ports — Connect 6-pole 3.5 mm captive screw connectors to these ports. These configurable digital input and

output ports are designed to connect to microphones with logic circuitry for mic mute and tally back functionality. Each port

provides a common ground.

KLine Outputs — Use 6-pole 3.5 mm captive screw connectors to connect up to four balanced or unbalanced mono line level

devices or two stereo devices (see diagram below).

Tip

Sleeve

Tip

Sleeve

Tip

Slee

Ring

Tip

Slee

Ring

6-pole Audio OUTPUT Wiring

Balanced Output Unbalanced Output

NO Ground Here

Figure 3. Audio Output Wiring

ATTENTION:

• For unbalanced audio outputs, connect the sleeves to the ground contact. DO NOT connect the

sleeves to the negative (-) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons

aux contacts négatifs (–).

When all connections have been made, power up the input and output devices, then apply power to the DMP 64 Plus.

Front Panel Features

OUTPUTSINPUTS

ACTIVITY

CONFIG EXP

USB

LAN 1

LAN 2

DMP 64 Plus

DIGITAL MATRIX PROCESSOR

123456 1234

CLIP

SIGNAL

CLIP

SIGNAL

AB C D E

Figure 4. DMP 64 Plus Front Panel

APower LED — Blinks during boot up and lights steadily when the DMP 64 Plus is operational.

BUSB Config Port — One USB mini-B port is used for configuration. This port can also be used for firmware updates.

CActivity Indicator LEDs — These LEDs indicate activity or status on the rear panel EXP, LAN, and USB ports.

DInput Indicator LEDs — Stacked green and red LEDs display input signal presence and input signal clipping.

EOutput Indicator LEDs — Stacked green and red LEDs display output signal presence and output signal clipping.

Figure 2

DMP 64 Plus • Setup Guide (Continued)

DSP Conﬁgurator Software Installation

There are no hardware controls for the DMP 64 Plus. All conguration and control is done using ExtronDSPCongurator

software. Install DSP Congurator on a PC running Microsoft®Windows®. For full computer requirements, see the DSP

Congurator product page on www.extron.com.

Download DSP Conﬁgurator from the Extron Website:

1. From the Extron home page (www.extron.com), click the Download tab to open the Download page.

2. Under Software, on the left side of the page, select DSP Configurator Software. The DSPConfiguratorSoftware

product page opens.

3. Click the Download button and follow the on-screen instructions.

NOTE: An Extron Insider account is required to download DSP Configurator.

DMP 64 Plus Conﬁguration

When power is connected to the DMP 64 Plus and the rest of the audio system, audio output can easily be tailored to any

listening environment. When conguration is required, changes are made using DSP Congurator.

Conﬁgure the DMP 64 Plus:

1. Ensure the control computer is connected to

the LAN port (recommended), front panel USB

Cong port, or RS-232 port of the

DMP 64 Plus. Full congurations that include

Macros, Internal Triggers (V models), and ACP

congurations require a LAN connection.

2. Start the DSP Congurator software.

a. From the splash screen drop-down

menu, select the DMP 64 Plus model

corresponding to the model connected to

the control computer.

a. Click OK and the main workspace opens.

3. The software starts in Emulate mode.

a. To create a conguration le ofine and

upload (push) that conguration to the

DMP 64 Plus at a later time, remain in Emulate mode and save the conguration le.

b. To push a conguration to the DMP64Plus or pull the current conguration from the DMP 64 Plus, enter Live mode.

When in Live mode, changes made in DSP Congurator affect the connected DMP64 Plus immediately. To enter Live

mode, click Live at the top of the DSP Congurator workspace, select Tools >Connect to Device, or press <F6>

on the keyboard.

NOTE: When Live mode is selected, a connection dialog box appears. Select the desired connection type and

follow the on-screen prompts (see the DMP 64 Plus User Guide for more information on connecting Live to a

device).

The main workspace provides access to mix matrices, gain blocks, and DSP processors for conguring the DMP 64 Plus. It also

provides a menu bar across the top with additional conguration tools. For more information about using DSP Congurator, see

the DSP Conﬁgurator Software section of the DMP 64 Plus User Guide or the DSP Conﬁgurator Help le that can be accessed by

selecting Help >Contents or pressing <F1> on the keyboard. Most dialog boxes within DSP Congurator contain a context-

sensitive Help button ( ) in the top right corner. Click this button to open the help le topic for that specic dialog box.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Conﬁgure Dante Device Settings:

Dante settings on all DMP 64 Plus AT models can be congured from DSP Congurator. The Dante device can be named here,

which aids in device identication in the DanteController software when there are multiple Dante devices on the audio network.

ATTENTION: It is essential that a Dante device be named before audio subscriptions with other devices are

established. Existing subscriptions are removed when a device is renamed.

To configure Dante device settings:

1. Open DSP Congurator and connect Live to the DMP 64 Plus AT (see step 3b on the previous page).

2. Select Tools > Device Settings. The Device Settings dialog box

opens.

3. From the tabs at the top of the Device Settings dialog box, select Dante

Device.

4. In the Device name eld, give the DMP 64 Plus a meaningful name

(such as device model and location) so that it can be easily identied in

DanteController.

5. Dante device network settings can also be congured from this dialog box.

Use the radio buttons and text elds to choose DHCP (recommended) or

Static IP and enter a static IP address conguration.

NOTE: The device name and IP configuration in the Dante Device tab

only affect the Dante interface of the DMP64Plus. These settings do

not affect the device name recognized in DSP Configurator or the IP

address of the rear panel LAN port.

6. Select Enable Redundant Mode only if conguring the DMP 64 Plus for use

on redundant networks. A separate set of redundancy network settings opens

for conguration (see Physical Dante Network Setup in the DMP 64 Plus User

Guide for more information on redundant conguration).

7. Click Apply.

8. Click OK to conrm changes and close the Device Settings dialog box.

For more information on conguring a DMP 64 Plus in Dante Controller, refer to the Dante Controller section of the

DMP64 PlusUser Guide (www.extron.com).

68-3291-50 Rev. A

09 19

Andere Handbücher für DMP 64 Plus

Inhaltsverzeichnis

Andere Extron electronics Computerhardware Handbücher

Extron electronics

Extron electronics UCS FT 901 Bedienungsanleitung

Extron electronics

Extron electronics Instruction Card Video DC Block Technisches Handbuch

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Bedienungsanleitung

Extron electronics

Extron electronics Quantum Ultra Series Bedienungsanleitung

Extron electronics

Extron electronics IPL Pro S1 Bedienungsanleitung

Extron electronics

Extron electronics SC 210 Bedienungsanleitung

Extron electronics

Extron electronics Annotator 300 Bedienungsanleitung

Extron electronics

Extron electronics EDID 101H 4K PLUS Bedienungsanleitung

Extron electronics

Extron electronics PIP 422 Bedienungsanleitung

Extron electronics

Extron electronics AXP 64 C AT Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T/R 301 Bedienungsanleitung

Extron electronics

Extron electronics Annotator Bedienungsanleitung

Extron electronics

Extron electronics DVI Output Card Bedienungsanleitung

Extron electronics

Extron electronics IPL Pro Series Bedienungsanleitung

Extron electronics

Extron electronics DMP 128 FlexPlus Bedienungsanleitung

Extron electronics

Extron electronics Quantum Ultra Bedienungsanleitung

Extron electronics

Extron electronics AXP 64 C AT Bedienungsanleitung

Extron electronics

Extron electronics IPCP 505 Bedienungsanleitung

Extron electronics

Extron electronics IPL M PDP-ES Montage- und Bedienungsanleitung

Extron electronics

Extron electronics EDID 101H 4K PLUS Bedienungsanleitung

Extron electronics

Extron electronics StudioStation 100 Bedienungsanleitung

Extron electronics

Extron electronics DMP 44 LC Bedienungsanleitung

Extron electronics

Extron electronics DMP 128 Plus Bedienungsanleitung

Extron electronics

Extron electronics Annotator 300 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung