EyeView SD-0400HL Benutzerhandbuch



960HWD1

DigitalVideoRecorder



QuickOperationGuide



Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.

This manual is applicable to the following models:

SD-0400HL, SD-0802HL, SD-1602HL.

DVR Pre-Installation

This Series DVR is highly advanced surveillance equipment that should be installed with care. Please take into

consideration the following precautionary steps before installation of the DVR.

1. Keep all liquids away from the DVR.

2. Install the DVR in a well-ventilated and dust-free area.

3. Ensure environmental conditions meet factory specifications.

4. Install a manufacturer recommended HDD.

DVR Installation

During the installation of the DVR:

1. Use brackets for rack mounting.

2. Ensure there is ample room for audio and video cables.

3. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter.

4. Connect both the alarm and RS-485 cable.

5. Allow at least 2cm (~0.75-inch) of space between racks mounted devices.

6. Ensure the DVR is grounded.

7. Environmental temperature should be within the range of -10 ºC ~ 55 ºC, 14ºF ~ 131ºF.

8. Environmental humidity should be within the range of 10% ~ 90%.

Hard Disk Installation

Before you start:

Before installing a hard disk drive (HDD), please make sure the power is disconnected from the DVR. A factory

recommended HDD should be used for this installation.

Tools Required: Screwdriver.

Steps (for SD series):

1. Remove the cover from the DVR by unfastening the screws on the back and side.

2. Install the HDD in the HDD rack using the provided screws. Fasten the screws on the

bottom to fix the HDD.

Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

3. Connect the HDD to the motherboard of the DVR with the included data cable.

4. Connect the power cable to the HDD.

5. Re-install the cover of the DVR and fasten screws.

Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

Front Panel

SD Series:

The front panel of SD series is shown below:

Table1DescriptionofControlPanelButtons 

No. Name Function Description

1 POWER POWER indicator turns green when DVR is powered up.

2 STATUS STATUS indicator lights in red when data is being read from or written to HDD.

3 Tx/Rx Tx/Rx indictor blinks green when network connection is functioning properly.

4 USB Interface Connects USB mouse or USB flash memory devices.

5 IR Receiver Receiver for IR remote.

Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

Rear Panel

SD-0400HL:

SD-0802HL:

SD-1602HL:

34 5 78910

12 6

Table2DescriptionofRearPanel

No. Item Description

1 VIDEO IN BNC connector for analog video input.

2 VIDEO OUT BNC connector for video output.

3 USB Interface Connects USB mouse or USB flash memory devices.

4 HDMI HDMI video output.

5 VGA DB15 connector for VGA output. Display local video output and menu.

6 AUDIO IN RCA connector for audio input.

7 AUDIO OUT RCA connector for audio output.

8 LAN Interface RJ45 10M / 100M Ethernet interface.

9 RS-485 Interface Connector for RS-485 devices. Connect the D+ and D- terminals to R+

and R- terminals of PTZ receiver respectively.

10 12V 12VDC power supply.

11 POWER Switch for turning on/off the device.

12 GND Ground(needs to be connected when DVR starts up)

Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

RS-485 Connections

To connect RS-485 devices (e.g., pan/tilt unit) to the DVR:

Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part.

Ensure signal cables are in tight.

Note: Make sure the pan/tilt receiver unit is connected to the D+ and D- of the RS-485 terminal of SD-0400HL,

SD-0802HL, SD-1602HL.

Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

Specifications

Model SD-04000HL SD-0802HL SD-1602HL

Video

compression H.264

Video input 4-ch 8-ch 16-ch

Video input

interface BNC (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive

Audio

compression G.711

Audio input 1-ch, RCA (2.0 Vp-p, 1 kΩ)

Video/Audio

input

Two-way audio

input 1-ch, RCA (2.0 Vp-p, 1 kΩ) (using the audio input)

HDMI/VGA

output

1-ch, resolution:

1080P: 1920×1080/60Hz; SXGA: 1280×1024/60Hz;

720P: 1280×720/60Hz; XGA: 1024×768/60Hz

CVBS output 1-ch, BNC (1.0 Vp-p, 75 Ω),

resolution: PAL: 704 × 576, NTSC: 704 × 480

Encoding

resolution WD1 / 4CIF / 2CIF / CIF / QCIF

Frame rate 25 fps (P) / 30 fps (N)

Video bit rate 32 Kbps ~ 3072 Kbps, or user defined (Max. 3072 Kbps)

Audio output 1-ch, RCA (Linear, 1 kΩ)

Audio bit rate 64 Kbps

Dual-stream Support; sub-stream @ CIF/ QCIF

Stream type Video, Video & Audio

Video/Audio

output

Synchronous

playback 4-ch 8-ch 16-ch

SATA 1 SATA interface 2 SATA interfaces

Hard disk Capacity Up to 4TB capacity for each disk

Network

interface 1, RJ45 10M / 100M Ethernet interface

Serial interface 1 RS-485 interface, half-duplex

External

interface

USB interface 2, USB 2.0

Power supply 12 VDC

Consumption

(without hard

disk or

DVD-R/W)

≤10 W ≤15 W ≤20 W

Working

temperature -10 ºC ~+55 ºC

Working

humidity 10% ~ 90%

Chassis Standalone 1U chassis 19-inch rack-mounted 1U chassis

Dimensions

(W × D × H) 315 × 230 × 45 mm 445 × 290 × 45mm

General

Weight (without

hard disk or

DVD-R/W)

≤2 kg ≤4 kg ≤4 kg

Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

HDD Storage Calculation Chart

The following chart shows an estimation of storage space used based on recording at one channel for an hour at a

fixed bit rate.

Bit Rate Storage Used

96K 42M

128K 56M

160K 70M

192K 84M

224K 98M

256K 112M

320K 140M

384K 168M

448K 196M

512K 225M

640K 281M

768K 337M

896K 393M

1024K 450M

1280K 562M

1536K 675M

1792K 787M

2048K 900M

3072Kbps 1350M

Note: Please note that supplied values for storage space used is just for reference. Storage space used is estimated

by formulas and may have some deviation from actual value.

Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

Menu Operation

Menu Structure

The menu structure of the SD series DVR is shown as below:

Startup and Shutdown

Proper startup and shutdown procedures are crucial to expanding the life of the DVR.

Before you start:

Check that the voltage of the extra power supply is the same with the device’s requirement, and the ground

connection is working properly.

Starting up the device:

Steps:

1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an

Uninterruptible Power Supply (UPS) be used in conjunction with the device.

2. Press the POWER button on the rear panel. The Power indicator LED should turn green indicating that the

unit begins to start up.

Shutting down the device:

Steps:

1. Enter the Shutdown menu.

Menu > Shutdown

2. Click the Shutdown button to enter the following dialog box:

Quick Operation Guide of SD-0400HL, SD-0802HL, SD-1602HL Series DVR

3. Click the Yes button. The following message box pops up:

4. Turn off the power switch on the rear panel of DVR.

Using the Setup Wizard

The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard starts

once the device has loaded.

Operating the Setup Wizard:

1. Select the system resolution from the dropdown menu. The default resolution is 1280×1024/60Hz.

Click Apply to save the resolution settings.

2. Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup wizard.

You can also click Cancel to exit the Setup Wizard, or use the Setup Wizard next time by leaving the “Start

wizard when device starts?” checkbox checked and exit.

Inhaltsverzeichnis

Andere EyeView DVR Handbücher

EyeView

EyeView SD-0400A Betriebsanleitung

Beliebte DVR Handbücher anderer Marken

FLIR

FLIR M3100E Series Bedienungsanleitung

VTRACKPRO

VTRACKPRO FPRO300 Bedienungsanleitung

Swann

Swann NVR-7085 models Bedienungsanleitung

XtendLan

XtendLan DVR-1670C Bedienungsanleitung

urmet domus

urmet domus 1093/004AHD Bedienungsanleitung

Holux

Holux M1 Bedienungsanleitung

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Bedienungsanleitung

Whistler

Whistler D16VRS Bedienungsanleitung

Defender Security

Defender Security 82-20235 Bedienungsanleitung

MISUMI

MISUMI MP-WF100M Bedienungsanleitung

Speco

Speco D8HU Bedienungsanleitung

UST

UST DDR-E04AA Gebrauchsanweisung

Consolidated

Consolidated Digital Video Recorder Bedienungsanleitung

Mace

Mace DVR0404RW Kurzanleitung

RCA

RCA RTD315W Bedienungsanleitung

FSM

FSM Colibri Grande PRO Bedienungsanleitung

Hauppauge

Hauppauge HD PVR 2 Bedienungsanleitung

Identivision

Identivision ICR-PH161i PIONEER Bedienungsanleitung