F&F PCS-516 DUO Bedienungsanleitung

- 1 -

PCS-516 DUO

Time relay,

10-function

The PCS-516 DUO time relay is used for time control in industrial

and home automation systems (such as : ventilation, heating,

lighting, signaling, etc.).

A. ON delay

After the supply voltage is switched on (the green LED U is on),

the contact remains in position 11-10 and the set operating time

counts down. After the preset time has elapsed, the contact swi-

tches to position 11-12 (the red LED is on). To execute the

operating mode of the relay again you need to switch off the

power supply voltage and switch it back on.

Purpose

Features of work

F&F Filipowski sp. j.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: biuro@fif.com.pl

Do not dispose of this device in the trash along with other waste!

According to the Law on Waste, electro coming from households free of charge and can

give any amount to up to that end point of collec� on, as well as to store the occasion of

the purchase of new equipment (in accordance with the principle of old-for-new, regard-

less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the

environment and human health.

- 2 -

B. OFF delay

The contact remains in position 11-10 until the relay is switched

on. After the supply voltage is switched on (the green LED U is

on), the contact is switched in position 11-12 and the set ope-

rating time t is measured (the red LED is on). To execute the

operating mode of the relay again you need to switch off the

power supply voltage and switch it back on.

C. ON delay – cyclic

On delay operating mode is carried out cyclically at equal in-

tervals between the preset operating time and break time.

D. OFF delay – cyclic

Off delay operating mode is carried out cyclically at equal in-

tervals between the preset operating time and break time.

Generating pulse 0.5 s after the preset time t.

Generating a single pulse with time tby the rising edge of the

 signal. During the time measurement, the system does not

react to  pulses.

Generating a single pulse with time tby the trailing edge of the

 signal. During the time measurement, the system does not

react to  pulses.

Off delay with back-up feature The rising edge of the  si-

gnal causes the relay to be switched on, while the trailing edge

causes the start of time measurement. Applying the  signal

during the time measurement causes the cycle to be extended

- 4 -

by another time twith the trailing edge.

Generating a single pulse 0.5 s after time twith the triggered

trailing edge of the  signal.

Switching off the relay for a specific time twith the rising edge of

the  signal. During the time measurement, the system does

not react to  signal.

When the RESET voltage is applied during the execution

of the given function, it causes:

»for functions A, B, C, D, F – the implementation of the

operating mode from the beginning;

»for functions F, G, H, I – the return of the relay to the

initial state and waiting for the  signal;

»for function K – permanent switching on of the relay

contact in position 11-12.

- 5 -

Setting the rotary timer switch in position:

»ON when the power supply is on closes the contact

permanently in position 11-12;

»OFF when the power supply is on closes the contact

permanently in position 11-10.

Using the time range setting knob T↔, set one of the selected

ranges, then using the time setting knob T×, set the selected va-

lue on a scale from 1 to 12. The product of these values is equal

to the operating time (for example: 1 m × 7 = 7 min.).

Using the  dial, set one of the functions (for example func-

tion A – off delay).

Working time setting

Working mode setting

- 6 -

When the power supply of the relay is switched on, the

system does not react to the change of time range and

working time settings.

Operation with the newly set time range and operating

mode takes place after the power supply is switched off

and back on.

With the power supply switched on, it is possible to

smoothly adjust the time within the time range of 1÷12.

  0.1÷1.2 sec  10÷120 min.

  1÷12 sec  2÷24 godz.

  10÷120 sec  1÷12 days (24÷288 h)

  1÷12 min.  2÷24 days (48÷576 h)

ON when the power supply is on, the contact is perma-

nently closed in position 11-12.

OFF when the power supply is on, the contact is perma-

nently closed in position 11-10.

1.Turn off the power supply.

2.Fix the relay on a rail in the switchboard.

3.Connect the power wires according to the as marked: 230 V to

terminals 1-3 and 24 V to terminals 1-6.

Connect only one of the selected voltages!

Time ranges

Mounting

- 7 -

4.Connect the power supply circuit of the receiver in series to

terminals 11-12.

Wiring diagram

- 8 -

Description of terminals

- 9 -

1-3 230 V power supply relay

1-6 24 V power supply relay

7  control signal input

9  control signal input

11  contact power input

10 output: break contact (passive)

12 output: closing contact (active)

power supply 195÷253 V AC

21÷27 V AC/DC

maximum load current (AC-1) 8 A

contact separated 1×NO/NC

working time (adjustable) 0.1 s÷576 h

activation delay <50 ms

power supply indication green LED

contacts state indication red LED

power consumption 0.8 W

terminal 2.5 mm² screw terminals

tightening torque 0,4 Nm

working temperature -25÷50°C

dimensions 1 module (18 mm)

mounting on TH-35 rail

protection level IP20

Technical data

- 10 -E200505

The F&F products are covered by a warranty of the 24 months

from the date of purchase. Effective only with proof of purchase.

Contact your dealer or directly with us.

F&F Filipowski sp. j. declares that the device is in conformity

with the essential requirements of The Low Voltage Directive

(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)

Directive 2014/30/UE. The CE Declaration of Conformity, along

with the references to the standards in relation to which confor-

mity is declared, can be found at www.fif.com.pl on the product

page.

Warranty

CE declaration

Inhaltsverzeichnis

Andere F&F Relais Handbücher

F&F

F&F BIS-413M-LED Bedienungsanleitung

F&F

F&F PCS-516UNI Bedienungsanleitung

F&F

F&F EPP-618 Bedienungsanleitung

F&F

F&F BIS-410-24V Bedienungsanleitung

F&F

F&F BIS-408 Bedienungsanleitung

F&F

F&F 5908312592389 Bedienungsanleitung

F&F

F&F PK-4PZ Bedienungsanleitung

F&F

F&F BIS-411 Bedienungsanleitung

F&F

F&F SWITCH & ENERGY Wi-R1S1-P Bedienungsanleitung

F&F

F&F PP-2Z Bedienungsanleitung

F&F

F&F CP-721-FPV Bedienungsanleitung

F&F

F&F PCR-513 Bedienungsanleitung

F&F

F&F BIS-411i Bedienungsanleitung

F&F

F&F BIS-411B-LED Bedienungsanleitung

F&F

F&F BIS-412M 24V Bedienungsanleitung

F&F

F&F PK-1Z-LED 230 V Bedienungsanleitung

F&F

F&F BIS-411 1R1Z Bedienungsanleitung

F&F

F&F PK-3P Bedienungsanleitung

F&F

F&F MST-03 Bedienungsanleitung

F&F

F&F BIS-411B Bedienungsanleitung

F&F

F&F PCS-516UNI Bedienungsanleitung

F&F

F&F BIS-410-LED Bedienungsanleitung

F&F

F&F BIS-411-LED Bedienungsanleitung

F&F

F&F BIS-408i Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Pilz

Pilz PNOZ X10 Betriebsanleitung

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung