FireAngel Wi-Safe 2 Bedienungsanleitung

User Manual

LOW FREQUENCY

SOUNDER

W2-LFS-630

Keeping the hard of hearing and high risk

safe from ﬁre and carbon monoxide

For a full range of carbon monoxide alarms

visit www.ﬁreangel.co.uk

CONTENTS

Note: This User Manual is also available in large text and other

formats. Please call 0800 141 2561 for further information.

INTRODUCTION. . . . . . . . . . . . . . . . . . . . . 2

KEY FEATURES . . . . . . . . . . . . . . . . . . . . . 2

INSTALLINGTHE LOW FREQUENCY SOUNDER . . . 4

CONNECTINGTHE BATTERY/MAINS POWER. . . . . 4

WIRELESSLY INTERLINKINGTHE LOW FREQUENCY

SOUNDERTOYOUR WI-SAFE 2® SMOKE OR

CO ALARM. . . . . . . . . . . . . . . . . . . . . . . . 6

TO REMOVETHE LOW FREQUENCY SOUNDER

FROMTHE WIRELESS NETWORK . . . . . . . . . . . 8

TESTINGTHE LOW FREQUENCY SOUNDER WITH

YOUR WI-SAFE 2®SMOKE / CO ALARMS . . . . . . . 9

POSITIONING . . . . . . . . . . . . . . . . . . . . . . 11

INSTALLINGTHE LOW FREQUENCY SOUNDER . . .12

LIMITATIONS . . . . . . . . . . . . . . . . . . . . . .12

OPERATION . . . . . . . . . . . . . . . . . . . . . . .13

UNPLUGGING FROMTHE MAINS/POWER CUT . . .14

PRODUCT INDICATORS (LEDS) . . . . . . . . . . . .15

WHATTO DO IFYOUR LOW FREQUENCY

SOUNDER GOES INTO ALARM . . . . . . . . . . . . 16

WHATTO DO INTHE EVENT OF A SMOKE ALARM

TRIGGERINGTHE LOW FREQUENCY SOUNDER . . .17

WHATTO DO INTHE EVENT OF A CARBON

MONOXIDE ALARMTRIGGERINGTHE LOW

FREQUENCY SOUNDER . . . . . . . . . . . . . . . .18

REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . .19

TROUBLESHOOTING . . . . . . . . . . . . . . . . . .20

DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . .21

WARRANTY . . . . . . . . . . . . . . . . . . . . . . .21

INTRODUCTION

IMPORTANT: If you are installing this product for

use by others, you must leave this manual (or a copy

of it) for the end user.

Wi-Safe 2®is the very latest in wireless technology

from Sprue Safety Products. It provides a network

of wireless radio frequency (RF) communication

which can trigger Wi-Safe 2®Alert products to alarm

simultaneously in the event of danger.

This Low Frequency Sounder, when interlinked with

Wi-Safe 2®enabled Smoke alarms and/or Wi-Safe 2®

enabled Carbon Monoxide (CO) Alarms (purchased

separately) will provide warning of danger from

smoke and/or carbon monoxide for people who may

respond to a lower frequency audible sound.

The Low Frequency Sounder has been speciﬁcally

designed to provide additional protection to standard

smoke alarms in the event of a ﬁre.

A low frequency signal is more likely to wake up high

risk individuals such as children, those with mild to

moderate hearing loss, older people and people

under the inﬂuence of alcohol than a regular smoke

alarm, according to research*

*Bruck, D. & Thomas, I (2007) Waking effectiveness of alarms

(auditory, visual and tactile) for adults who are hard of hearing.

Optimizing Fire Alarm Notiﬁcation for High Risk Groups Research

Project. pp.66.

KEY FEATURES

• Uses Wi-Safe 2®technology to provide warning of

ﬁre or Carbon Monoxide (CO). Wi-Safe 2®products

can be interlinked to create a network, meaning

if smoke or CO triggers any alarm in the network,

all other networked alarms and ancillary devices

activate.

• When used with Wi-Safe 2®enabled Smoke and/or

CO alarms, the Low Frequency Sounder provides

additional protection when a standard high pitched

sound alone may not be enough.

• Provides a simple two button press “learn in”

process to wirelessly interlink with Wi-Safe 2®

smoke alarms or CO alarms

• The Low Frequency Sounder provides a remote

low level testing facility for testing interlinked

smoke and CO alarms, avoiding the need to reach

up to ceiling mounted alarms to test.

• Mains powered with rechargeable battery back-up

(must be replaced after 5 years).

• The Low Frequency Sounder will detect and

demonstrate a fault or low battery warning with

any smoke alarm or CO alarm within the inter-

linked network.

• The Low Frequency Sounder is suitable for wall

mounting with 2 screw ﬁxings or free standing.

• Designed for use with Smoke alarms and Carbon

Monoxide alarms from the Wi-Safe 2®range

(purchased separately).

Wi-Safe 2®Low Frequency Sounder Pack

Contains:

1. Low Frequency Sounder

2. Plug in AC mains adaptor, 9V 2A rated output

3. Replaceable, rechargeable 5 year life battery

4. Wall ﬁxing screws

NOTE: The Low Frequency Sounder is only

compatible with Wi-Safe 2®alarms from Sprue

Safety Products. It cannot be wirelessly

interlinked with other models or brands of

smoke alarms or carbon monoxide alarms. It is

not compatible with products from FireAngel’s

original Wi-Safe range.

The Wi-Safe 2®product range is currently being

expanded. Please visit www.ﬁreangel.co.uk for

details of the latest additions to the portfolio.

INSTALLING THE LOW

FREQUENCY SOUNDER

PREPARATION: Please ensure you have read and

understood this entire manual before installing your

Low Frequency Sounder.

Your Low Frequency Sounder is designed to be used

in conjunction with Smoke alarm(s) and CO alarm(s)

from the Wi-Safe 2®range of products.

It is recommended that for optimum protection

from smoke and/or carbon monoxide, one Wi-Safe

2®smoke alarm is ﬁtted in each living room of your

home, including bedrooms, and one Wi-Safe 2®CO

alarm is ﬁtted in every room containing a fossil fuel

appliance, with your Low Frequency Sounder.

NOTE: Up to ﬁfty Wi-Safe 2®enabled

Smoke alarms, CO alarms and/or Wi-Safe 2®

accessories can be interlinked (“learned in”)

to a single network.

Ensure all smoke alarms and/or CO alarms to be

used are installed, tested and working correctly as

ﬁg1

per the instructions in their respective user manuals.

CONNECTING THE

BATTERY/MAINS POWER

NOTE: The Low Frequency Sounder requires both a

continuously powered AC (mains) electrical supply

and internal battery for its normal operation. The

battery accompanying this product is rechargeable

and charges when there is mains power to the Low

Frequency Sounder.

1. Remove the battery cover on the back of the Low

Frequency Sounder by pressing the tabs on either

side of the battery cover as shown (ﬁg 1).

2. Connect the rechargeable battery, by aligning the

terminals (red wire to red wire) and clipping the

connectors together.

CAUTION: Connect the battery with mains

power disconnected.

3. Place the battery into the recess. NOTE:The

battery cable needs to be positioned underneath

the battery. Place the cable into the bottom of the

recess and place the battery over the top, with the

battery text facing up as shown (ﬁg 2). This will

ensure that the battery is installed correctly.

4. Assemble the power cable and adaptor by

positioning the plug head as shown. Rotate onto

the adaptor clockwise until it clicks into position.

ﬁg3

5. Plug the power cable in to the Low Frequency

Sounder by ﬁtting the cable into the connection

point as shown (ﬁg 4).

ﬁg2 ﬁg4

6. Replace battery cover.

7. Plug in the mains adaptor and turn the power

on.The green power LED should illuminate.

Within a few seconds, the amber fault LED will be

continuously illuminated; both alarm LEDs (smoke

and CO) should be extinguished.

NOTE: When power is ﬁrst provided to the Low

Frequency Sounder, the amber fault LED and both

red alarm LEDs will ﬂash twice; the amber LED will

then illuminate continuously to indicate that the unit

has not been “learned in” to any network. This will

typically happen when the battery is connected. If the

has not retained any residual charge during shipping,

it will happen when the mains power is connected.

You will also see a low battery warning indication

as the amber fault LED will ﬂash once every ﬁve

seconds.

WIRELESSLY INTERLINKING

THE LOW FREQUENCY

SOUNDER TOYOUR

WI-SAFE 2®SMOKE OR

CO ALARM

It is recommended that you read through

these “learn in” instructions before starting.

Learning a Low Frequency Sounder into a new

Wi-Safe 2®system:

1. Place one of your Smoke or CO alarms on to its

baseplate.You will use this product to interlink

with the Low Frequency Sounder to create a

network.

2. Brieﬂy push and release the learn button located

in a circular hole in the back of the Low Frequency

Sounder using a pen, or similar as shown

(ﬁg 5).

3. After pressing this button, the two Alarm (red)

LEDs on the front of the unit will ﬂash and then

illuminate for 5 seconds.

4. During this period, while the red LEDs are

illuminated, press the test/reset button on the

Smoke or CO alarm to wirelessly interlink the two

products.The Smoke alarm (or CO alarm) will emit

an audible signal, and the red (Alarm) LED on the

Smoke (or CO alarm) will also ﬂash.

5. After learning in the Low Frequency Sounder into

the alarms, test the units separately to ensure they

are wirelessly interlinked (see below) and test

again in ﬁnal installed position.

Learning a Low Frequency Sounder into an

existing Wi-Safe 2®system:

1. Locate a Smoke / CO alarm that is already part of

the existing Wi-Safe 2® system.You will use this

product when adding the Low Frequency Sounder

into the network.

2. Follow steps from point 2 above.To add any

further alarms to the network, press the learn

button on the new alarm then the test button on

the Low Frequency Sounder, or on any alarm

already learned in to the network.

NOTE: The battery is supplied in a discharged or

partially discharged state and will require up to 72

hours of charging (continuous connection to the

mains supply) to ensure that it is fully charged. During

this period the amber fault LED may ﬂash once every

ﬁve seconds to indicate that the battery is low. The

following tests however may be carried out before

the charging is complete.

Further Wi-Safe 2®products (including additional

ﬁg5

Low Frequency Sounders) can be learned into the

network in the same way. The learn button on the

Low Frequency Sounder is located on the back of the

product.

After learning in the Low Frequency Sounder into the

alarms, test the units separately to ensure they are

wirelessly interlinked (see below).

TO REMOVE THE

LOW FREQUENCY SOUNDER

FROM THE WIRELESS

NETWORK

IMPORTANT: If you need to remove (“unlearn”) the

Low Frequency Sounder from the wireless network,

eg for house alterations, or to dispose of the unit

it is important to follow the instructions below to

“unlearn” the unit from the wireless network. Failure

to do so means that the network continues to try and

communicate with the removed unit, and will result

in a system fault.

1. Brieﬂy push and release the learn button located

in the circular hole in the back of the Low

Frequency Sounder using a ball point pen or

similar as shown (ﬁg 5). The two red alarm LEDs

on the front of the Low Frequency Sounder will

illuminate as you push the button.

2. Push and hold the learn button a second time.

The red alarm LEDs will illuminate. Hold the

button until the red alarm LEDs extinguish.

3. The red alarm LEDs will then perform a sequence

of two long and three short ﬂashes. The amber

fault LED will illuminate to conﬁrm that the Low

Frequency Sounder is no longer interlinked to the

wireless network.

4. Press the test button on the Low Frequency

Sounder. It should not cause other Wi-Safe 2®

alarms to sound. However, if the Low Frequency

Sounder is still interlinked, repeat the above

procedure.

Andere Handbücher für Wi-Safe 2

Inhaltsverzeichnis

Andere FireAngel Rauchmelder Handbücher

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel THERMISTEK HT-630 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel ST-230 Bedienungsanleitung

FireAngel

FireAngel Thermoptek WST-630 Bedienungsanleitung

FireAngel

FireAngel SI-610 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-632 Bedienungsanleitung

FireAngel

FireAngel THERMOPTEK Wi-Safe 2 Bedienungsanleitung

FireAngel

FireAngel ST-620 Thermoptek Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622-T Bedienungsanleitung

FireAngel

FireAngel Wi-Safe 2 Thermoptek WST-630-NEU Bedienungsanleitung

FireAngel

FireAngel SI-610 Bedienungsanleitung

FireAngel

FireAngel ST-623E-INT Bedienungsanleitung

FireAngel

FireAngel SW1 Bedienungsanleitung

FireAngel

FireAngel Wi-Safe2 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel HW1 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel THERMISTEK HT-630 Bedienungsanleitung

FireAngel

FireAngel ST-630-INT Bedienungsanleitung

FireAngel

FireAngel THERMOPTEK ST-623E Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung

Radal Technology

Radal Technology Cig-Arrête CSA-POD Bedienungsanleitung