Forney 410 Bedienungsanleitung

Adjust wire feed

speed ( ) and

voltage ( )

Flux-

Cored

* Face the appropriate groove

towards the inside of machine

Set drive roll

Solid

wire

Connect to input power

With contact tip

3/8” from metal,

depress trigger

completely to

initiate arc

Install wire spool

0.023” (0.6mm) - 0.035” (0.9mm) diameter

8” (200mm)

wire spool

4” (100mm)

wire spool

Feed wire and set pressure

Knob set ~2-3

marks

Remove

consumables

and depress

trigger until

wire comes out.

Replace

consumables

See chart on welder

for correct settings

FIND MORE INFORMATION AT FORNEYIND.COM

4. 5. 6.

9. 10. 11.

Connect MIG gun and ground clamp

QUESTIONS OR TROUBLE? Contact Forney Industries at 1-800-521-6038 [email protected]

forneyind.com

MIG QUICK START GUIDE

220 MP WELDER

ITEM# 410

Set polarity for MIG (solid wire)

or Flux-Cored

Solid wire Flux-cored

Read user manual

Select process

Pressure knob

NOTE: If using gas:

2. Attach hose to

regulator and

regulator to

gas bottle

1. Attach gas hose

to machine

MIG Gun Ground

Clamp

• Generator OK with continuous output >

5,000 W (120V) or 10,000 W (230V)

• Extension cord: #12 AWG (120V) or #8

AWG (230V) or larger. 25’ (8m) or shorter

extension cords recommended

MIG TROUBLESHOOTING TIPS

Improper wire spool installation

Use wire with a diameter between 0.023” (0.6mm) and 0.035” (0.9mm). Larger diameters draw too much amperage.

Trying to weld single pass on material larger than 3/8” (9.5mm) thick is not possible with this machine. Multi-pass recommended for thicker materials.

Welder should be the only thing plugged into the circuit.

• Usually due to low input power.

• Welder should be only thing plugged into circuit.

• Avoid using extension cords. If one must be used, it must be 3 conductor #12 AWG or larger up to 25 feet.

• Generators must be a minimum 5,000W continuous output with no low-idle function (or low-idle off), 5% THD Max.

Frequently tripping circuit breaker or exceeding duty cycle

Low weld output or poor fusion

Wire from spool to drive should relax with a slight curve after feeding.

• Can cause feed issues and inconsistent weld quality.

• Verify all parts are in the proper place. Refer to manual.

Too much spool tension

Knob set ~2-3 marks

Too little pressure = Roll can slip and feed can

be erratic.

Too much pressure = can crush wire, causing

wire feeding problems and welder damage.

Incorrect drive roll pressure

8” (200mm) wire spool 4” (100mm) wire spool

Trigger must be pulled to initiate the arc. This

will initiate the arc and begin feeding the wire.

DEPRESS THE TRIGGER COMPLETELY

No arc start on contact

• Can cause feed and weld issues and

arc instability.

• Each component must be sized for

wire diameter used.

Mismatched drive roll, liner, or

contact tip size

To ensure maximum quality, always clean

and prepare welding surfaces.

Workpiece Preperation

Connect ground clamp to clean, bare metal. No rust,

paint or other coatings. Attach the ground clamp

directly to the workpiece if you are experiencing issues.

Workpiece grounding

Low weld output or poor fusion

110-120V

208-240V

• Usually due to low input power.

• Welder should be only thing plugged into circuit.

• Avoid using extension cords. If one must be used, it must be 3 conductor #8 AWG.

• Generators must be a minimum 10,000W continuous output with no low-idle function (or low-idle off), 5% THD Max.

Connect to input power

4. 6.

Choose between High Frequency (HF) start

or Lift start.

Adjust amperage per

material thickness

Connect TIG torch lead

to gas (100% Argon)

Connect TIG torch and

ground clamp

ELECTRODE IS ALWAYS ELECTRICALLY

HOT WHILE IN TIG MODE

FIND MORE INFORMATION AT

FORNEYIND.COM

TIG TROUBLESHOOTING TIPS

Low weld output or poor fusion

Welder should be the only thing plugged into the circuit.

Frequently tripping circuit breaker or exceeding

duty cycle

• Not recommended for this machine.

• Output is DC only which is not recommended for TIG

welding aluminum.

Aluminum welding

TIG QUICK START GUIDE

220 MP WELDER (NOT RECOMMENDED FOR ALUMINUM)

ITEM# 410

Read user manual

Select process

ONLY

TIG Torch Ground

Clamp

• Usually due to low input power.

• Welder should be only thing plugged into circuit.

• Avoid using extension cords. If one must be used, it must be 3 conductor #8 AWG.

• Generators must be a minimum 10,000W continuous output with no low-idle

function (or low-idle off), 5% THD Max.

208-240V

QUESTIONS OR TROUBLE? Contact Forney Industries at 1-800-521-6038 [email protected]

forneyind.com

• Generator OK with continuous output >

5,000 W (120V) or 10,000 W (230V)

• Extension cord: #12 AWG (120V) or #8

AWG (230V) or larger. 25’ (8m) or shorter

extension cords recommended

To ensure maximum quality, always clean

and prepare welding surfaces.

Workpiece Preperation

Connect ground clamp to clean, bare metal. No rust,

paint or other coatings. Attach the ground clamp

directly to the workpiece if you are experiencing issues.

Workpiece grounding

• Usually due to low input power.

• Welder should be only thing plugged into circuit.

• Avoid using extension cords. If one must be used, it must be 3 conductor #12 AWG

or larger up to 25 feet.

• Generators must be a minimum 5,000W continuous output with no low-idle function

(or low-idle off), 5% THD Max.

Low weld output or poor fusion

110-120V

* TIG Torch sold separately

STICK TROUBLESHOOTING TIPS

*Performance may vary by brand

Connect to input power Recommended electrodes

4. 6.

FIND MORE INFORMATION AT FORNEYIND.COM

Adjust amperage per

chart on the inside of

the welder

Electrode Electrode Amperage

3/32” 1/8” 5/32”

E6010

E6011

E6013

E7014

E7018

E308L

Ni55

30-75 75-125 110-165

40-85

40-90

70-90

65-100

40-70

50-65

75-125

70-110

90-140

110-165

75-115

80-95

110-165

115-140

140-190

150-220

105-160

110-135

Connect electrode

holder and ground

clamp according to

desired polarity

Usually

DCEP -

Electrode

Positive

Use 3/16” diameter electrodes or smaller. Some 3/16” will draw too much amperage.

Trying to weld single pass on material larger than 3/8” thick is not possible with this machine. Multi-pass recommended for thicker materials.

Welder should be the only thing plugged into the circuit.

Frequently tripping circuit breaker or exceeding duty cycle

STICK QUICK START GUIDE

220 MP WELDER

ITEM# 410

Read user manual

Select process

Electrode Holder Ground

Clamp

• Usually due to low input power.

• Welder should be only thing plugged into circuit.

• Avoid using extension cords. If one must be used, it must be 3 conductor #12 AWG

or larger up to 25 feet.

• Generators must be a minimum 5,000W continuous output with no low-idle function

(or low-idle off), 5% THD Max.

Low weld output or poor fusion

110-120V

• Usually due to low input power.

• Welder should be only thing plugged into circuit.

• Avoid using extension cords. If one must be used, it must be 3 conductor #8 AWG.

• Generators must be a minimum 10,000W continuous output with no low-idle function

(or low-idle off), 5% THD Max.

208-240V

QUESTIONS OR TROUBLE? Contact Forney Industries at 1-800-521-6038 [email protected]

forneyind.com

• Generator OK with continuous output >

5,000 W (120V) or 10,000 W (230V)

• Extension cord: #12 AWG (120V) or #8

AWG (230V) or larger. 25’ (8m) or shorter

extension cords recommended

To ensure maximum quality, always clean

and prepare welding surfaces.

Workpiece Preperation

Connect ground clamp to clean, bare metal. No rust,

paint or other coatings. Attach the ground clamp

directly to the workpiece if you are experiencing issues.

Workpiece grounding

Low weld output or poor fusion

Inhaltsverzeichnis

Andere Forney Schweißsystem Handbücher

Forney

Forney MIG 180FI Bedienungsanleitung

Forney

Forney FLEX 30 PLASMA ST Bedienungsanleitung

Forney

Forney 700P Bedienungsanleitung

Forney

Forney Easy Weld 261 Bedienungsanleitung

Forney

Forney 270 Bedienungsanleitung

Forney

Forney 430 Bedienungsanleitung

Forney

Forney 140 MIG WELDER Bedienungsanleitung

Forney

Forney 317 Bedienungsanleitung

Forney

Forney Easy Weld 20P Bedienungsanleitung

Forney

Forney Easy Weld Bedienungsanleitung

Forney

Forney 220 ST Bedienungsanleitung

Forney

Forney 140 MIG WELDER Bedienungsanleitung

Forney

Forney 298 Bedienungsanleitung

Forney

Forney 140 MP Bedienungsanleitung

Forney

Forney 140 MP Bedienungsanleitung

Forney

Forney 220 AC/DC Bedienungsanleitung

Forney

Forney 95FI Bedienungsanleitung

Forney

Forney 242 Bedienungsanleitung

Forney

Forney 220 MP Bedienungsanleitung

Forney

Forney 140 MP Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Forney

Forney Easy Weld 180 ST Bedienungsanleitung

Forney

Forney Easy Weld series Bedienungsanleitung

Forney

Forney 95FI Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung