FRC TH4C Bedienungsanleitung

Installation Guide

TH4C

4-Channel DVR

Document Number:

XE-SNB2-TH4CPM-R0A

TH4C Installation Guide

Table of Contents

System Components.. . . . . . . . . . . . . . . . 4

Required Tools & Equipment. . . . . . . . . . 4

System Diagram. . . . . . . . . . . . . . . . . . . . 5

TH4C Installation. . . . . . . . . . . . . . . . . . . . 6

Installation Best Practices. . . . . . . . . . . . . . . . . 6

Installing the DVR. . . . . . . . . . . . . . . . . . . . . . . 7

Installing the Adaptor Harness (Optional). . . . . 8

Firmware Updates. . . . . . . . . . . . . . . . . . . . . . . 9

Hardware Installation Checklist. . . . . . . . . . . . 10

TH4C Operation. . . . . . . . . . . . . . . . . . . . 11

DVR Front Panel Features. . . . . . . . . . . . . . . .11

DVR Back Panel Features.. . . . . . . . . . . . . . . 12

Video System Status. . . . . . . . . . . . . . . . . . . . 13

Video Flagging.. . . . . . . . . . . . . . . . . . . . . . . . 14

Using On-screen Keyboards. . . . . . . . . . . . . . 14

Health Check. . . . . . . . . . . . . . . . . . . . . . . . . . 15

TH4C Administration . . . . . . . . . . . . . . . 16

Accessing the On-screen Display. . . . . . . . . . 16

Working with Video. . . . . . . . . . . . . . . . . . . . . 19

TH4C Basic Conguration. . . . . . . . . . . 22

Setting up the DVR. . . . . . . . . . . . . . . . . . . . . 22

Time and Date. . . . . . . . . . . . . . . . . . . . . . . . . 24

Title and Display. . . . . . . . . . . . . . . . . . . . . . . 25

Cameras Settings. . . . . . . . . . . . . . . . . . . . . . 28

Conguring Signals. . . . . . . . . . . . . . . . . . . . . 29

Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . 31

Copying DVR Conguration. . . . . . . . . . . . . . 33

TH4C Advanced Conguration. . . . . . . 35

Conguring Recording Settings.. . . . . . . . . . . 35

Network Settings. . . . . . . . . . . . . . . . . . . . . . . 36

Advanced Network Settings. . . . . . . . . . . . . . 38

G-Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Speed Settings. . . . . . . . . . . . . . . . . . . . . . . . 41

GPS Fencing. . . . . . . . . . . . . . . . . . . . . . . . . . 42

User Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . 43

System Settings.. . . . . . . . . . . . . . . . . . . . . . . 44

Monitor Settings.. . . . . . . . . . . . . . . . . . . . . . . 45

Appendix. . . . . . . . . . . . . . . . . . . . . . . . . 47

Customer Service. . . . . . . . . . . . . . . . . . . . . . 47

Product Information. . . . . . . . . . . . . . . . . . . . . 47

Warranty And End-User License Agreement. 47

TH4C Installation Guide

p. 4

System Components

Document Number: XE-SNB2-TH4CPM-R0A

System Components

The typical installation components are listed below.

• TH4C video recorder with SD card, locking front cover, cable cover, fasteners, and mounting plate.

• Analog High Denition cameras (HD1W or HD1Q)

• Analog Standard Denition cameras (CA10, CJ, CQ or RVC)

• Camera harness (HExHD for AHD and HE or HExHD for SD)

• Power harness (PH2X2MFJR)

• Adaptor harness (WT1)

• Expansion harness (optional)

• Diagnostic button (optional) and extension cable

• Smart-Reach cellular router

• Smart-Reach WiFi bridge

• Smart-Reach GPS receiver

• Portable video monitor (optional)

Required Tools & Equipment

The DVR system must be installed by a professional installer. A professional installer has the experience and equipment to

install and congure this DVR system to run properly.

Check that you have all the system components and inspect the units for any scratches or damage before installing.

Keys included in package contents:

• DVR keys for securing the removable hard drive.

Conguration equipment:

• For on-screen conguration: portable video monitor and mouse.

• For vMax Web conguration: laptop and an Ethernet cable.

Only The actual contents of your installation package may vary, depending on the options selected.

NOTE: Installation Package i

TH4C Installation Guide

p. 5

System Diagram

Document Number: XE-SNB2-TH4CPM-R0A

System Diagram

Click here to see an Interactive System

Diagram with more information.

TH4C Installation Guide

p. 6

TH4C Installation

Document Number: XE-SNB2-TH4CPM-R0A

TH4C Installation

Installation Best Practices

This section provides best practices for installing Seon TH4C DVRs. Before you begin, keep in mind that it is your responsibility

to avoid damaging safety or electrical systems. If you are not condent in your ability to perform the procedures in this guide,

please contact FRC Technical Service at 1.800.645.0074 or visit the FRC website Contact page for assistance.

The following table outlines the physical and environmental requirements for installing a TH4C DVR:

VENTILATION Install the DVR away from any sort of heat outlet, heater, or AC blower. Do not operate the

DVR in a closed-in area, or restrict ventilation in any way. The DVR requires air circulation to

maintain optimum operation temperature and provide best performance. Do not expose the

DVR to moisture!

SURFACE Do not mount the DVR to a plastic panel or other surface that is subject to constant

vibration.

ORIENTATION Mount the DVR in either a horizontal or vertical orientation, or hung right side up, but NOT

upside down.

CLEARANCE Allow sufcient clearance of at least 6 inches in front of the DVR and 2 inches to each side

for removal of the security front cover and easy access to the hard drive and USB ports. Allow

sufcient clearance behind the DVR for camera cables, mounting cables, Ethernet cables,

and power cables.

MOUNTING

CABLES

The radius for the mounting cables will be dictated by the cable cover. The rear-most surface

of the cable cover will be about 3 inches from the back of the DVR to allow camera cables to

bend over each other.

ETHERNET CABLES Avoid right angle bends in the Ethernet cables.

POWER CABLES Provide enough slack on the power cable to prevent any force from being exerted on the

connectors. A single 4-inch diameter loop is sufcient.

WARNING:

It is your responsibility to avoid damaging safety or electrical systems. Ensure you read and understand the TH4C DVR

Installation Requirements.

If you are not condent in your ability to perform the procedures in this manual, please contact FRC Support at 1.800.645.0074

or service@reresearch.com.

TH4C Installation Guide

p. 7

TH4C Installation

Document Number: XE-SNB2-TH4CPM-R0A

Installing the DVR

The DVR typically ships with the locking front cover, mounting plate, and cable cover off, but in the shipping box. The hard

disk drive is in a separate box in the system shipping kit.

To install the DVR:

1. Slide the SD card slot door up.

2. Slide an SD card into the slot:

• Ensure the metal contacts on the card

are facing down.

• Gently push the card into the slot until

it clicks.

3. Slide the SD card slot door down until it

clicks.

4. Insert the key into the SD card lock and

rotate a quarter turn to lock the drive.

5. Select an appropriate mounting location and

orientation. For more information, see TH4C

Installation Requirements.

6. Fasten the DVR to the mounting surface

with the four self-drilling screws.

7. Connect the necessary cables and

components. For more information, nd the

TH4C Quick Installation Guide in the Seon

Documentation Library and read the section

TH4C Operation in this document.

IMPORTANT:

Ensure you lock the SD card, or data will not be saved on the card. The SD LED on the DVR front panel glows green

when the card is locked in place.

TH4C Installation Guide

p. 8

TH4C Installation

Document Number: XE-SNB2-TH4CPM-R0A

Installing the Adapter Harness (Optional)

The Adapter Harness (Part # WT1) connects the DVR to Signal inputs, and to the optional Event/Diagnostic button and

Wake on Input trigger.

To install the Adaptor Harness, connect the 2x6

Microt to the SIGNALS socket on the DVR. Then:

1. Connect the 5 signal input wires.

2. Connect the 1x5 Microt to the Adapter harness

for the Event/Diagnostic button (optional).

3. Remove the 1x3 Microt and connect the

green and black wires to a Wake on Input

trigger (optional).

TH4C Installation Guide

p. 9

TH4C Installation

Document Number: XE-SNB2-TH4CPM-R0A

To update the Firmware version:

1. Power up the DVR using the vehicle ignition.

2. Insert the USB memory device with the new rmware version into the USB port on the DVR.

3. After the DVR starts up, right-click in the On-screen Display

and select:

Conguration System Program Update

4. In the Program Update tab, click Update. A conrmation

window appears.

5. Click Yes to proceed or No to cancel. Yes starts the

rmware update, and a progress bar displays the

percentage complete.

6. Once the update is nished, the DVR automatically restarts.

7. Remove the USB memory device.

Firmware Updates

Firmware controls how DVR features operate, including the Playback and Conguration menu displays. FRC may direct you

to install a rmware update when new features are added or specic issues are addressed.

The current rmware version appears in the top-right corner

of every Conguration menu. For instructions on opening the

Conguration menus, see TH4C Administration: Accessing the

On-Screen Display.

Only install rmware updates as directed by Seon Service.

NOTE: Firmware Updates

After restarting, the DVR may take up to 3 minutes to load and complete the upgrade. Wait until the DVR nishes loading.

NOTE: Completing Upgrade

TH4C Installation Guide

p. 10

TH4C Installation

Document Number: XE-SNB2-TH4CPM-R0A

HARNESSES (CAMERA, RECORDER, AND ACCESSORIES)

Ensure cables and harnesses are properly secured.

Check that sharp metal edges are not touching cables or harnesses.

Ensure connections are solid (no shorts).

CAMERAS

Ensure tight mounting.

Examine the internal harness connections and ensure they are solid.

Ensure the lid is properly seated on the gasket and secured tightly.

Check camera(s) eld of view.

DVR

Ensure tight mounting.

Check that all connections are tight.

SYSTEM

Install fuses.

Plug portable video monitor into DVR, and power up the DVR from the vehicle ignition.

Congure the DVR to required specications locally using the mouse and monitor, or remotely by accessing vMax

Web via WiFi or Ethernet using a PC. For more information, see "Basic Conguration" on page 22.

Conrm the LAN, HDD, and PWR status indicators on the DVR front panel work properly.

Conrm that all cameras and audio sources operate properly.

Test audio/video record and playback.

Reformat the hard drives by navigating to Main Menu Conguration System Program Update Format.

A warning message tells you all data will be erased. Click Yes. When the process completes and a message

appears, click OK. Exit the Conguration setting menu, and system setup is complete.

Fasten and lock the front cover. Secure the cable cover on the DVR using the screws provided.

Hardware Installation Checklist

Inhaltsverzeichnis

Andere FRC DVR Handbücher

FRC

FRC TH4 Bedienungsanleitung

Beliebte DVR Handbücher anderer Marken

FLIR

FLIR M3100E Series Bedienungsanleitung

VTRACKPRO

VTRACKPRO FPRO300 Bedienungsanleitung

Swann

Swann NVR-7085 models Bedienungsanleitung

XtendLan

XtendLan DVR-1670C Bedienungsanleitung

urmet domus

urmet domus 1093/004AHD Bedienungsanleitung

Holux

Holux M1 Bedienungsanleitung

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Bedienungsanleitung

Whistler

Whistler D16VRS Bedienungsanleitung

Defender Security

Defender Security 82-20235 Bedienungsanleitung

MISUMI

MISUMI MP-WF100M Bedienungsanleitung

Speco

Speco D8HU Bedienungsanleitung

UST

UST DDR-E04AA Gebrauchsanweisung

Consolidated

Consolidated Digital Video Recorder Bedienungsanleitung

Mace

Mace DVR0404RW Kurzanleitung

RCA

RCA RTD315W Bedienungsanleitung

FSM

FSM Colibri Grande PRO Bedienungsanleitung

Hauppauge

Hauppauge HD PVR 2 Bedienungsanleitung

Identivision

Identivision ICR-PH161i PIONEER Bedienungsanleitung