Front Runner LAMS001 Bedienungsanleitung

front runner

LAMS001

ENG

Thank you for purchasing a Front Runner Mercedes Sprinter Ladder.

Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.

Refer to Page 2 for a list of all the components, quantities and tools required.

READ ME !

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD

RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT

RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND

DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO

INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY

FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

MERCEDES SPRINTER LADDER

TOOLS NEEDED

FIGURE 1.1

GET ORGANIZED

IN THE BOX

17mm

6.5mm

12mm 4mm

13 14 18

1 1 X WSA Bottom Ladder Assembly

2 1 X WSA Top Ladder Assembly

3 1 X Large Washer Plate

4 2 X Bent Joiner Plate

5 2 X Joiner Plate

6 2 X Washer Plate

7 4 X M10 x 30 Hex Bolt

8 8 X M10 Flat Washer

9 4 X M10 Nyloc Nut

10 8 X M10 Nut Caps

11 10 X M6 x 20 Button Head Screw

12 1 X M6 Spring Washer

13 19 X M6 X 12 X 1SS Flat Washer

14 9 X M6 Nyloc Nut

15 1 X Jack Nut Tool

16 1 X M6 Jack Nut

17 1 X M6 x 30 Button Head Screw

18 9 X M6 Nut Cap

19 4 X Rubber Pads

10mm

PREPARE2

2.1

2.2

2.3

Loosely ﬁt the two Joiner Plates (Item 5)

using four M6 x 20 Button Head Screws,

eight M6 x 12 x 1SS Flat Washers and four

M6 Nyloc Nuts (Items 11, 13 & 14) to the

left-hand side of the Ladder.

Loosely ﬁt the two Bent Joiner Plates

(Item 4) using four M6 x 20 Button Head

Screws, eight M6 x 12 x 1SS Flat Washers

and four M6 Nyloc Nuts (Items 11, 13 & 14)

to the right-hand side of the Ladder.

Remove backing and place the four Rubber

Pads (Item 19) onto the ladder's feet and

trim to ﬁt.

11 13

514

10mm

4mm

10mm

FIT AND SECURE3

3.1

3.2

3.3

Working on the right rear door, open the

door and have a friend position the Ladder

so that the mounting holes align with the

existing holes in the top and bottom door

hinges outer castings as shown in 3.2

Loosely secure the Ladder to the hinge outer

casting at the top of the door using two

M10 x 30 Hex Bolts, four M10 Flat Washers,

two Washer Plates and two M10 Nyloc Nuts

(Items 7,8,6 & 9).

Repeat the above step for the lower door

Hinge mount.

Align the Ladder before fully tightening all

the fasteners.

Mark the left-hand side top & bottom holes

on the door as shown in 3.3.

Remove the Ladder and all fasteners.

DOOR HINGE

17mm

DOOR HINGE

15 16

FIT AND SECURE3

3.4

3.5

3.6

TOP HOLE:

Using a 6.5mm drill bit, drill a pilot hole in

the center of your marking, making sure to

go through both skins of the door.

BOTTOM HOLE:

Again using a 6.5mm drill bit, drill a pilot

hole on the bottom mark. Open the hole

using a 12mm drill bit.

Only go through the ﬁrst outer skin of the

door.

Apply some Anti Rust on the exposed metal

of each hole.

Insert the M6 x 30 Button Head Bolt (Item 17)

into the one side of the Installer Wrench.

Loosely ﬁt a Jack Nut to the Button Head Bolt

as shown.

Place the assembly into the hole drilled in

3.4. Using a Cordless Drill and a 4mm Allen

Key Bit set the Jack Nut into the hole while

holding the Installer wrench ﬁrmly.

Make sure that the Jack Nut has pulled up

all the way to the inside skin of the door

panel.

11 13

314 18

Repeat steps in 3.2 and reﬁt the Ladder to

the door hinges.

Using M6 x 20 Button Head Screw,

M6 x 12 x 1SS Flat Washer, Large washer

Plate and M6 Nyloc Nut (Items 11,13, 3 &14)

for the top hole. Fully tighten.

"Finally," fully tighten the M6 x 20 Button

Head Screw, M6 Spring Washer and M6 x 12

x 1SS Flat Washer (Items 11,12 & 13) into

the pre-installed Jack nut installed in 3.5.

Fully tighten ﬁxings in 2.1 and 2.2. Finish off

by placing M6 Nut Caps (Item 18) over the

nuts.

The Large Washer Plate (Item 3) will only

be installed on the inside of the door with

Mercedes Sprinter's High Roof and Super

High Roof models.

6.5mm

12mm

4mm

10mm

17mm

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now's the time to visit your favorite Front Runner Dealer in person or online.

Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam

Share your adventures on:

FINISH

Congratulations! You did it. Take a step back and admire your work!

Inhaltsverzeichnis

Andere Front Runner Autozubehör Handbücher

Front Runner

Front Runner TRCA005 Bedienungsanleitung

Front Runner

Front Runner SSDS802 Bedienungsanleitung

Front Runner

Front Runner SSAM009 Bedienungsanleitung

Front Runner

Front Runner STRA057 Bedienungsanleitung

Front Runner

Front Runner RRAC248 Bedienungsanleitung

Front Runner

Front Runner TBMK009 Bedienungsanleitung

Front Runner

Front Runner SSLD001 Bedienungsanleitung

Front Runner

Front Runner FSLI023 Bedienungsanleitung

Front Runner

Front Runner FAJK010 Handbuch

Front Runner

Front Runner Pro Bike Carrier Bedienungsanleitung

Front Runner

Front Runner FSLI021 Bedienungsanleitung

Front Runner

Front Runner SSAM008 Bedienungsanleitung

Front Runner

Front Runner SSDS113 Bedienungsanleitung

Front Runner

Front Runner LATF002 Bedienungsanleitung

Front Runner

Front Runner KRTT001T Bedienungsanleitung

Front Runner

Front Runner LADD007 Bedienungsanleitung

Front Runner

Front Runner SLIMLINE II TRAY Bedienungsanleitung

Front Runner

Front Runner LALD009 Bedienungsanleitung

Front Runner

Front Runner LALD004 Bedienungsanleitung

Front Runner

Front Runner Pro Water Tank with Strap Bedienungsanleitung

Front Runner

Front Runner RRAC189 Kurzanleitung

Front Runner

Front Runner SLIMPRO KVXS006 Handbuch

Front Runner

Front Runner SHOWER ARM MKII Bedienungsanleitung

Front Runner

Front Runner JCH004 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung