Front Runner SSDR010 Bedienungsanleitung
1
DRAWer
SSDR010
INSTALL TIME: 30 Min
s
REV_A00
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR
VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY IN-
JURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER
PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PROD-
UCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTION
S
AND CAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDER-
STAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOR-
OUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSION
-
AL INSTALLER OR OTHER QUALIFIED PERSONNEL.
If you have purchased a vehicle specific Deck Set to go with your Drawer System, disregard this Fitting Instruction and
refer to your vehicle specific Instruction received with your Deck Set.
If you have not purchased a vehicle specific Deck Set, you may require additional fasteners and tools in order to create
four suitable mounting points on the vehicle to secure the Drawer System to. It is suggested that you read through the
Fitting Instructions, place Drawer System in the desired position on the vehicle and work out how best to secure the
Drawer System via the Turn Buckles and C-hooks supplied should the vehicle not have suitable mounting points.
2
GET ORGANIZED...
Here is what you are looking at for SSWO008:
You will need:
10 mm Flat & Socket Wrench
4 mm Hex Key
a Friend
Additional Fasteners and Tools de-
pending on application
REV_A00
Item # Quantity Description
1 1 DRAWER
2 4 TURNBUCKLE
3 4 WING NUT
4 4 D-RING
5 4 M6 x 20 HEX BOLT
6 4 M6 SPRING WASHER
7 4 M6 x 19 FLAT WASHER
8 6 EYE NUT
9 6 STUD PLATE
10 6NYLON WASHER
11 460mm C-HOOK
12 3M8 x 16 HEX BOLT
13 3M8 CHANNEL NUT
14 3M8 x 25 FLAT WASHER
15 3M8 SPRING WASHER
16 1TRACK
2
3
4
5
6
7
8
9
10
16
11
13
12
15
14
3
Install drawer
Loosen the round end of the four Turn Buckles (Item 2). Screw a M6 Wing Nut (Item 3) onto each round
end and reassemble the Turn Buckle as shown.
()A
Assemble the M6 Eye Nuts and Nylon
Washers (Items 7 & 8) to the Stud Plates
(Item 9) as shown.
()B
REV_A00
()c
Assemble two D-rings (Item 4) to either side of the Drawer as shown using the M6 x 20 Hex Bolts, M6 x 19
Flat Washers and M6 Spring Washers as shown.
4
Install drawer cont...
REV_A00
Slide a Channel Nut (Item 13) into each end of the Track (Item 16). Place the Track under the front of the
Drawer System and line the Channel Nuts in the Track up with the mounting holes in front corners of the
Drawer System. Loosely secure the Track in position using the two M8 x 16 Hex Bolts, two M8 x 25 Flat
Washers and two M8 Springs Washers (Items 12, 14, 15). Center the Track from left to right and fasten.
()D
(F )
Connect a Turn Buckle and C-Hook (Item 11) to each of the D-rings assembled to Drawer System in Step 2C
()E
Place the Drawer System into the vehicle and position as desired.
5
Install drawer cont...
REV_A00
With the Turn Buckles and C-hooks in position, work out how best to secure the "hook end " of the Turn
Buckle to the vehicle. Referring to the image below, note that the Turn Buckles must all pull away form
each other in order to prevent the Drawer System from moving one secured into position.
As mentioned on the front page, you may require additional fasteners and tools at this stage in order to
create suitable mounting points.
(
G
)
Once you have the four mounting points on your vehicle, secure the Drawer to the vehicle by tightening
the four Turn buckles. Once the Drawer is secure in position tighten the Wing Nuts on the Turn Buckles
and the Bolts securing the D-rings to the Drawer System and the vehicle's load bay.
()H
6
Install DrawER
REV_A00
Should you wish to use the Eye Nut
assemblies from Step 2B as tie down
points, they can be slid into any of the
three top extrusions as shown and
tightened in the required position.
()
I
Congratulations, you have completed your installation. Take a step back and admire your work. Good Job!
(
J
)
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
Now's the time to visit your favorite Front Runner dealer in person or online.
()A
Inhaltsverzeichnis
Andere Front Runner Autozubehör Handbücher
Front Runner
Front Runner TRCA009 Bedienungsanleitung
Front Runner
Front Runner FAJL002 Bedienungsanleitung
Front Runner
Front Runner RRAC901 Bedienungsanleitung
Front Runner
Front Runner TRAC003 Bedienungsanleitung
Front Runner
Front Runner GOFR001 Bedienungsanleitung
Front Runner
Front Runner TRCA004 Bedienungsanleitung
Front Runner
Front Runner LASJ003 Bedienungsanleitung
Front Runner
Front Runner LATR001 Bedienungsanleitung
Front Runner
Front Runner LAMG003 Bedienungsanleitung
Front Runner
Front Runner LAMS001 Bedienungsanleitung
Front Runner
Front Runner SSDR003 Bedienungsanleitung
Front Runner
Front Runner SSDR002 Bedienungsanleitung
Front Runner
Front Runner RRAC269 Bedienungsanleitung
Front Runner
Front Runner FAJK010 Handbuch
Front Runner
Front Runner BPTH007 Bedienungsanleitung
Front Runner
Front Runner TRCA005 Bedienungsanleitung
Front Runner
Front Runner FAJL004 Bedienungsanleitung
Front Runner
Front Runner RRAC018 Bedienungsanleitung
Front Runner
Front Runner RRAC202 Bedienungsanleitung
Front Runner
Front Runner TBRA039 Bedienungsanleitung
