Fujitsu Fi-60F Bedienungsanleitung

Getting Started

fi-60F Image Scanner

Getting Started

fi-60F Image Scanner

P3PC-1102-07EN

CONTENTS

■Regulatory Information ........................................................ ii

■Note, Liability ....................................................................... iv

■Safety Precautions ................................................................ v

Chapter 1 PREPARING THE SCANNER.................................. 1

1.1 Checking the Contents of the Scanner Package............. 1

1.2 Names and Functions of Parts.......................................... 1

Chapter 2 INSTALLATION OF THE SCANNER...................... 2

2.1 Installing the Scanner Application ................................... 2

2.2 Installing the Scanner ........................................................ 5

2.3 Connecting the Scanner to Your PC................................. 6

2.4 Confirming the Installation................................................ 7

2.5 Installing Adobe® Reader® ............................................... 8

Appendix 1 TROUBLESHOOTING........................................ AP-1

Appendix 2 DAILY CARE ...................................................... AP-3

INTRODUCTION

Thank you for purchasing the fi-60F Scanner product.

This document describes how to handle fi-60F Scanner

and basic operation methods. Before you start using fi-

60F Scanner be sure to thoroughly read this manual to

ensure correct use.

The "Operator’s Guide" is stored on the Setup Disk.

The guide provides useful and detailed information on

operations when you would like to use advanced fea-

tures, daily maintenance of the scanner, replacement of

consumables. Please also read the Operator’s Guide for

your reference.

■Regulatory Information

FCC Declaration

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not

occur in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by

one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment

and receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is

located.

•Consult your dealer or an experienced radio/TV

technician.

FCC warning: Changes or modifications not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

Canadian DOC Regulations

This digital apparatus does not exceed the Class B

limit for radio noise emissions from digital

apparatus set out in the Radio interference

Regulations of the Canadian Department of

Communications.

This Class B digital apparatus complies with

Canadian ICES-003.

Le présent appareil numérique n'émet pas de

parasites radioélectriques dépassant les limites

applicables aux appareils numériques de la classe

B et prescrites dans le Règlement sur le brouillage

radioélectrique dictées par le Ministère des

Communications du Canada. Cet appareil

numérique de la classe B est conforme à la norme

NMB-003 du Canada.

Bescheimigung des Herstellers /

Importeurs

Für den fi-60F wird folgendes bescheinigt:

•In Übereinsstimmung mit den Bestimmungen

der EN45014(CE) funkentstört

•Maschinenlärminformationsverordnung 3.

GPSGV: Der höchste Schalldruckpegel beträgt

70 dB (A) oder weniger, gemäß EN ISO 7779.

ATTENTION

The use of a shielded interface cable

is required to comply with the Class B

limits of Part 15 of FCC rules.

The length of the AC cable must be 2

meters (6.6 feet) or less.

iii

Use in High-safety Applications

This product has been designed and manufactured

on the assumption that it will be used in office,

personal, domestic, regular industrial, and

general-purpose applications. It has not been

designed and manufactured for use in applications

(simply called "high-safety applications" from

here on) that directly involve danger to life and

health when a high degree of safety is required,

for example, in the control of nuclear reactions at

nuclear power facilities, automatic flight control

of aircraft, air traffic control, operation control in

mass-transport systems, medical equipment for

sustaining life, and missile firing control in

weapons systems, and when provisionally the

safety in question is not ensured. The user should

use this product with adopting measures for

ensuring safety in such high-safety applications.

PFU LIMITED assumes no liability whatsoever

for damages arising from use of this product by

the user in high-safety applications, and for any

claims or compensation for damages by the user

or a third party.

Trademarks

Microsoft, Windows, Windows Server, and

Windows Vista are either registered trademarks or

trademarks of Microsoft Corporation in the United

States and/or other countries.

ISIS and QuickScan are trademarks or registered

trademarks of EMC Corporation in the United

States.

Adobe, the Adobe logo, Acrobat, and Adobe

Reader are either registered trademarks or trade

names of Adobe Systems Incorporated in the

United States and/or other countries.

Other company names and product names are the

registered trademarks or trademarks of the

respective companies.

How Trademarks Are Indicated In

This Manual

References to operating systems (OS) are

indicated as follows:

Where there is no distinction between the different

versions of the above operating system, the

general term "Windows " is used.

Dieses Gerät wurde nicht für die Benutzung in

unmittelbarer Umgebung starker Lichtquellen

(z. B.Projektoren) konzipiert.

Windows 2000 Windows®2000 Professional

operating system

Windows XP Windows®XP Home Edition

operating system,

Windows®XP Professional

operating system (32/64-bit)

Windows Sever

2003 Windows Server®2003,

Standard Edition (32/64-bit),

Windows Server®2003 R2,

Standard Edition (32/64-bit)

Windows Vista Windows Vista®Home Basic

operating system (32/64-bit),

Windows Vista®Home

Premium operating system (32/

64-bit),

Windows Vista®Business

operating system (32/64-bit),

Windows Vista®Enterprise

operating system (32/64-bit),

Windows Vista®Ultimate

operating system (32/64-bit)

Windows Sever

2008 Windows Server®2008

Standard (32/64-bit),

Windows Server®2008 R2

Standard

Windows 7 Windows®7 Home Premium

operating system (32/64-bit),

Windows®7 Professional

operating system (32/64-bit),

Windows®7 Enterprise

operating system (32/64-bit),

Windows®7 Ultimate operating

system (32/64-bit)

Manufacturer

PFU LIMITED

International Sales Dept., Imaging Business

Division, Products Group

Solid Square East Tower, 580 Horikawa-cho,

Saiwai-ku, Kawasaki-shi Kanagawa 212-8563,

Japan

Phone : (81-44) 540-4538

■Note, Liability

BEFORE USING THIS PRODUCT, PLEASE

READ THIS MANUAL CAREFULLY. IF THIS

PRODUCT IS NOT USED CORRECTLY,

UNEXPECTED INJURY CAN OCCUR TO

USERS OR BYSTANDERS.

Keep this manual in a safe place so that it can be

easily referred to during use of this product.

While all efforts have been made to ensure the

accuracy of all information in this manual, PFU

assumes no liability to any party for any damage

caused by errors or omissions or by statements of

any kind in this manual, its updates or

supplements, whether such errors are omissions or

statements resulting from negligence, accidents,

or any other cause. PFU further assumes no

liability arising from the application or use of any

product or system described herein; nor any

liability for incidental or consequential damages

arising from the use of this manual. PFU disclaims

all warranties regarding the information contained

herein, whether expressed, implied, or statutory.

Warning Indications Used In This

Manual

Symbols Used In This Manual

Screen Examples In This Manual

The screen examples in this manual are subject to

change without notice in the interest of product

improvement. If the actual displayed screen

differs from the screen examples in this manual,

operate by following the actual displayed screen

while referring to the User's Manual of the scanner

application you are using.

The screenshots in this manual were captured

from TWAIN scanner driver, ScandAll PRO Lite

Image Capturing Utility Software, ISIS scanner

driver, QuickScan™ image capturing software

and Adobe®Acrobat®.

About Maintenance

The user must not perform repairs on this scanner.

Contact the store where you purchased the scanner

or an authorized FUJITSU Image Scanner service

provider to have repairs done on this product.

This indication alerts operators

to an operation that, if not strictly

observed, may result in severe

injury or death.

This indication alerts operators

to an operation that, if not strictly

observed, may result in safety

hazards to personnel or damage

to equipment.

ATTENTION

This symbol alerts operators to partic-

ularly important information. Be sure

to read this information.

HINT

This symbol alerts operators to helpful

advice regarding operation.

A TRIANGLE symbol indicates that special

care and attention is required.

The drawing inside the triangle shows the

specific caution.

A CIRCLE with a diagonal line inside

shows action which users may not perform.

The drawing inside or under the circle

shows the specific action that is not

allowed.

Outline characters on a colored

background show instructions users should

follow.

It may also include the drawing that shows

the specific instruction.

■Safety Precautions

In the following warnings, "power cable" may refer to

the AC cable connected to the AC adapter collectively.

Do not damage the AC cable.

Use only specified AC cables and

connector cables.

Use this scanner only at the

indicated power voltage. Do not

connect to multiple-power strips.

Do not touch the AC cable with wet

hands.

Wipe any dust from the power plug.

Do not install the device in locations

that has oil smoke, steam, humidity,

and dust.

Turn the scanner OFF if it is

damaged.

Do not put liquids inside the scanner.

Do not touch the inside of the

scanner unless necessary.

A damaged AC cable may cause fire or

electric shock.

Be careful of the following when handling

the power cable:

•Do not moisten, modify, tie, bundle, or

wind the cable.

•Do not place heavy objects on the cable,

trap the cable in a doorway, drop or

damage the cable in any other way.

•Do not pull or forcibly bend or twist the

cable.

•Do not place any metal near to the plug

of the power cable.

Do not use damaged AC cables or power

plugs, or install any cables or power plugs

to loose wall sockets.

Use only specified AC cables and

connector cables. Failure to use the

correct cables might cause electric shock

and/or equipment failure.

Please don’t use the AC cable provided

with this scanner for other devices, since

this might cause equipment failure and

other troubles or an electric shock.

Use this scanner only at the indicated

power voltage and current. Improper

power voltage and current might cause

fire or electric shock. Do not connect to

multiple-power strips.

Do not touch the power plug with wet

hands. Doing so might cause electric

shock.

Wipe off any dust from the power cable,

metal parts on the power plug or metal

fittings with a soft, dry cloth.Accumulated

dust might cause fire or electric shock.

Do not install the scanner in locations

subject to oil smoke, steam, humidity, and

dust. Doing so might cause a fire or

electric shock.

If the scanner is damaged for any reason,

disconnect immediately the power plug in

order to turn out the scanner. Contact the

store where you purchased the scanner.

Do not insert or drop metal objects in to the

scanner. Do not scan wet documents or

documents with paper clips or staples. Do

not splash or allow the scanner to get wet.

If foreign objects (water, small metal

objects, liquids, etc.) get inside the scanner,

disconnect immediately the power plug in

order to turn out the scanner. Then, contact

the store where you bought the scanner or

the Maintenance Service Center. Pay par-

ticular attention to this warning in house-

holds where there are small children.

Do not take apart or modify the scanner.

The inside of the scanner contains high-

voltage components. Touching these

components might cause electric shock or

fire.

Do not use the scanner if there is a

strange odor.

Do not use aerosol sprays near the

scanner.

Do not install the scanner on

unstable surfaces.

Do not place heavy objects or stand

on top of the scanner.

Firmly insert the power plug.

Do not use the scanner immediately

after moving it from a cold place into

a warm room.

Before moving the scanner,

disconnect the power plug from the

power outlet.

Protect the scanner from static

electricity.

Disconnect the power plug from the

power outlet when the scanner is not

used for a long period of time

If you detect excessive heat coming from

the device or detect other problems such as

smoke, strange smells or noises,

disconnect immediately the power plug in

order to turn out the scanner. Make sure

that any smoke coming from it has stopped,

before contacting the store where you

bought the scanner or an authorized

FUJITSU scanner service provider.

Do not use any aerosol sprays or alcohol

based sprays to clean the scanner.

Dust blown up by strong air from the spray

may enter the inside of the scanner. This

may cause the scanner to fail or

malfunction.

Sparks, caused by static electricity,

generated when blowing off dust and dirt

from the outside of the scanner may cause a

fire.

Make sure that the scanner is installed on

a flat, level surface and that none of its

parts extend beyond the surface top, such

as a desk or table. Do not install the

scanner on unstable surfaces. Install the

scanner on a level surface that is free of

vibration to prevent it from falling.

Install the scanner on a strong surface that

will support the weight of the scanner and

other devices.

Do not place heavy objects on the scanner

or use the scanner's surface top to

perform other work. Improper installation

might cause injuries and equipment

failure.

Firmly insert the power plug as far it can

go into the power outlet.

Do not use the device immediately after

moving it from a cold place into a warm

room. Condensation may occur, which

might lead to scanning errors. Let the

device dry about one or two hours before

you use it.

Do not move the scanner with the power

and interface cables connected as this can

damage the cables, which can later cause

fire, electric shock as well as injury.

Before moving the scanner, be sure to

disconnect the power plug from the power

outlet, and all other data cables.

Make sure that the floor is free of any

obstructions.

Install the scanner away from strong

magnetic fields and other sources of

electronic noise. Also, protect the scanner

against any static electricity, which can

cause the scanner to malfunction.

When the scanner is not going to be used

for a long period of time, be sure to

disconnect the power plug from the power

outlet for safety.

vii

Do not install the scanner in direct

sunlight.

Before moving the scanner, make

sure the shipping lock is locked.

Do not install the scanner under direct

sunlight or near heating apparatus. Doing so

might cause excessive heat to build up

inside the scanner, which can cause

scanner trouble or even fire. Install the

scanner in a well-ventilated location.

When moving the scanner, be sure to lock

the shipping lock in order to prevent

damages to the scanner.

Chapter 1 PREPARING THE SCANNER

1.1 Checking the Contents of

the Scanner Package

When you open the scanner package, please handle the

main unit and its attachments carefully.

Make sure it contains all the parts listed in the package

contents list that is included in the package box.

If any parts are missing or defective, contact your sales

representative. Handle the scanner and accessories with

care.

1.2 Names and Functions of Parts

This section describes the scanner parts and their func-

tions.

■Front

■Inside

■Rear

Document bed

Document holding pad

Document cover

LED

DC inlet

USB interface connector

Shipping lock

Security slot

Chapter 2

INSTALLATION OF THE SCANNER

2.1 Installing the Scanner

Application

Both the scanner driver and image capturing application

software (called "application" hereafter) must be

installed on your PC.

Two types of drivers are available for this scanner, a

TWAIN Scanner Driver and a ISIS Scanner Driver, as

well as two software applications, ScandAll PRO Lite

and QuickScan Pro™ (Trial), are provided with this

product. The following sections describe how to install

each driver and application.

For TWAIN Scanner Driver

■

Preparation

Confirm the following items before installing the appli-

cation.

•Remove the Setup DVD-ROM from its package,

but do not insert the Setup DVD-ROM into the

DVD driver yet.

•Uninstall any older versions of TWAIN driver if

already installed.

■

Installing the TWAIN Scanner Driver

1. Turn on your PC and log on to Windows.

2. Insert the Setup DVD-ROM into the DVD drive.

⇒<SETUP DISK START UP SCREEN> appears.

3. Click [INSTALL], and then click [TWAIN

Driver].

ATTENTION

Please install the scanner driver

before connecting the scanner to your

PC.

If you connect the scanner before

installing the scanner driver, the scan-

ner will not operate correctly.

If you have connected the scanner

beforehand, the "Found New Hard-

ware Wizard" screen appears (this

screen might differ slightly according

to the used OS) . On this screen, click

the [Cancel] button to close the

Wizard screen and install the scanner

driver first.

ATTENTION

Uninstall [Scanner Utility for Microsoft

Windows] from [Add/Remove Pro-

grams] of the control panel.

HINT

Windows XP screenshots are used in

this section as examples. The windows

and operations may slightly vary

depending on your OS.

ATTENTION

Log on as a user with "Administrator"

privileges (privileges of the adminis-

trator of your PC).

ATTENTION

This screen may not appear when the

"Autoplay" setting of your PC is OFF.

In this case, run "AutoPlayer.exe" in

this DVD-ROM directly from the

"Explorer" or "My Computer".

Andere Handbücher für fi-60F

Inhaltsverzeichnis

Andere Fujitsu Scanner Handbücher

Fujitsu

Fujitsu M4099D Bedienungsanleitung

Fujitsu

Fujitsu FI-6130 Bedienungsanleitung

Fujitsu

Fujitsu fi-5650C Konfigurationshandbuch

Fujitsu

Fujitsu fi-4860C Handbuch

Fujitsu

Fujitsu ScanSnap iScanner fi-6010N Handbuch

Fujitsu

Fujitsu ScanSnap S1100 Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Handbuch

Fujitsu

Fujitsu fi-5530C - Document Scanner Handbuch

Fujitsu

Fujitsu fi-6400 Bedienungsanleitung

Fujitsu

Fujitsu M3099EH Bedienungsanleitung

Fujitsu

Fujitsu ScanSnap N1800 Bedienungsanleitung

Fujitsu

Fujitsu 50FH5037E-02 Installations- und Betriebshandbuch

Fujitsu

Fujitsu S510 - ScanSnap - Document Scanner Bedienungsanleitung

Fujitsu

Fujitsu M3096EX/GX Handbuch

Fujitsu

Fujitsu fi-4860C Handbuch

Fujitsu

Fujitsu ScanPartner FI-4110CU Bedienungsanleitung

Fujitsu

Fujitsu FI 4220C - Document Scanner Bedienungsanleitung

Fujitsu

Fujitsu FI 6140 - Document Scanner Handbuch

Fujitsu

Fujitsu ScanSnap fi-5110EOX Bedienungsanleitung

Fujitsu

Fujitsu FI-5530C2 Bedienungsanleitung

Fujitsu

Fujitsu ScanSnap fi-5110C Handbuch

Fujitsu

Fujitsu PA03630-B055 Bedienungsanleitung

Fujitsu

Fujitsu fi-5650C Bedienungsanleitung

Fujitsu

Fujitsu fi-6140Z Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung

Visioneer

Visioneer CardReader 100 Kurzanleitung

Rohde & Schwarz

Rohde & Schwarz TSME6 Bedienungsanleitung

Fujitsu fi-60F Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken