Fujitsu SPARC Enterprise T2000 Bedienungsanleitung

This guide describes the minimum steps you must perform to power on and boot your server for the first time

using the preinstalled Solaris™ Operating System (Solaris OS).

FIGURE 1 SPARC Enterprise T2000 Server

Shipping Contents

Before You Begin

For quick installation and configuration, follow these steps. For more detailed information, refer to the complete

online product documentation set at: http://www.fujitsu.com/sparcenterprise/manual/

Understand the following information before you set up the server for the first time:

■Do not apply power until instructed to do so – This system includes a system controller (SC) that is used to

configure and boot the host server. To properly configure the host server and view SC messages, do not apply

AC power to the server until the SC and host networking connections are made, as described in this guide.

■Choose the best instructions for your situation – The quick setup instructions in this guide work for any

networking environment, and require the use of a terminal device for connection to a serial port. If you have

a networking environment running DHCP, you can configure your system using the Ethernet management

port. To take advantage of the DHCP setup method, refer to the online installation guide in the online product

documentation set at: http://www.fujitsu.com/sparcenterprise/manual/

Quantity Item

1Server

1 Rackmounting kit with cable

management assembly

2 RJ-45 Ethernet cable

1 RJ-45 to DB-25 adapter (crossover)

1 RJ-45 to DB-9 adapter (crossover)

1 Wrist strap

2Powercords(packagedseparately)

SPARC®Enterprise T2000 Server Getting Started Guide

■Set aside sufficient time – Installation times vary, but if you are performing these setup instructions for the

first time, plan to spend about 45 to 75 minutes to complete all of these instructions. Additional time might be

required for installing optional hardware and rackmounting kits.

■Obtain a terminal device – You configure this rackmountable server through the SC using the built-in serial

management and network management ports, and not through a graphical interface and keyboard. To

communicate with the SC, you will need a terminal device, which can be a terminal, terminal server, or laptop

running terminal emulation software.

■Gather your configuration information – During the configuration, you are prompted for time zone and

networking parameters for your environment. Use TABLE 1 to record your configuration information.

TABLE 1 Configuration Information

Parameter Description You r Ent r y

Language Select a number from the displayed language list.

Locale Select a number from the displayed locale list.

Termi nal Typ e Select a terminal type that corresponds with your terminal device.

Network? Select Yes.

Multiple Network

Interfaces

Select the network interfaces that you plan to configure. If you are not sure,

select the first one in the list.

DHCP? Select Yes or No according to your network environment.

Host Name Enter the host name for the server.

IP Address Enter the IP address for the selected Ethernet interfaces.

Subnet? Select Yes or No according to your network environment.

Subnet Netmask (If subnet was Yes) Enter the netmask for the subnet for your network

environment.

IPv6? Specify whether or not to use IPv6. If you are not sure, select No to

configure the Ethernet interface for IPv4.

Security Policy Select either standard UNIX security (No) or Kerberos Security (Yes). If you

are not sure, select No.

Confirm Review the onscreen information and change it if needed. Otherwise,

continue.

Name Service Select the name service according to your network environment.

Note – If you select a name service other than None, you will be prompted

for additional name service configuration information.

NFSv4 Domain

Name

Select the type of domain name configuration according to your

environment. If you are not sure, select Use the NFSv4 domain derived

by the system.

Time Zone

(Continent)

Select your continent.

Time Zone

(Country or Region)

Select your country or region.

Time Zone Select the time zone.

Date and Time Accept the default date and time, or change the values.

root Password Enter the root password twice. This password is for the superuser account

for the Solaris OS on this server. This password is not the SC password.

Quick Setup Instructions

1. Unpack the server, and check that you received all of the shipping contents.

2. Place the server in its intended location for verification.

For rackmounting instructions, refer to the instructions included with the rail kit, the service label on the

server, and to the online SPARC Enterprise T2000 Server Installation Guide.

3. Connect a serial cable between the server’s SER MGT port (FIGURE 2) and a terminal device.

This connection provides your initial communication with the system controller (SC).

The device must be set up to communicate using 9600 baud, 8 bit, no parity, 1 stop bit. A null modem

configuration is needed, meaning the transmit and receive signals are reversed (crossed over) for DTE to

DTE communications. You can use the supplied RJ-45 crossover adapters with a standard RJ-45 cable to

achieve the null modem configuration.

FIGURE 2 Server Connections

4. (Optional) Connect an Ethernet cable between the server’s NET MGT port (FIGURE 2) and the network to

which future connections to the SC and host will be made.

After the initial configuration of the system using the SER MGT port, communication with the SC and host is

usually performed through this Ethernet interface. To enable this port you must configure it (configure IP

addresses and so forth). Refer to the SPARC Enterprise T2000 Server Installation Guide for instructions.

5. Connect an Ethernet cable between one of the server’s NET ports (FIGURE 2) and the network to which the

server will communicate.

6. Plug the power cords into the power supplies and into separate power sources.

To provide redundancy, plug each power supply into a separate power source. The system can operate with

only one power connection, but there is no redundancy in this case.

When power is applied, the SC initializes and power supply LEDs illuminate. After a few minutes, the SC

initialized or powered on yet.

7. At the terminal device, log in to the SC as admin.

After a brief delay, the SC prompt (sc>) is displayed. admin is a factory default account that does not have

a password until you establish one.

8. Set a password for the ALOM CMT admin account.

Subsequent access to the ALOM CMT admin account will require the password.

Additional information, such as how to set up the NET MGT port, is available in the online documentation

set.

9. Power on the server and redirect the host output to display on the serial terminal device.

After you run the console command, the input and output displays messages from the host. The host

initialization process takes approximately 20 minutes to complete.

10. When prompted, follow the onscreen instructions and enter the configuration information.

Refer to TABLE 1 for the list of configuration information and your entries. You will be prompted to confirm

the configuration several times, enabling confirmation and changes. If you are not sure how to respond to a

particular value, you can accept the default and make future changes when the Solaris OS is running.

When the configuration menus are completed, the server reboots and displays the Solaris login prompt.

11. Log in to the server and explore the capabilities.

The following commands provide information about the system:

■showrev – Displays the hostname and system architecture information. Use the -a option with this

command to see the patches that are installed.

■psrinfo – Displays information about the number and status of the processors and cores in the host.

Review the Solaris OS man pages and documentation for more details.

Please login: admin

sc>

sc> password

password: Changing password for admin

Setting password for admin.

New password: ********

Re-enter new password: ********

sc>

sc> poweron

ASC Alert: Host System has Reset

sc> console

Accessing Important Information for SPARC Enterprise Series Servers

Before you deploy your server, check for the Product Notes for your server and other important information on

the following websites.

Global Site

http://www.fujitsu.com/sparcenterprise/manual/notes/

North American Site

https://download.computers.us.fujitsu.com/

Japanese Site

http://primeserver.fujitsu.com/sparcenterprise/manual/notes/

Accessing Documentation

The following websites provide the latest versions of SPARC Enterprise Series manuals:

Global Site

http://www.fujitsu.com/sparcenterprise/manual/

North American Site

https://download.computers.us.fujitsu.com/

Japanese Site

http://primeserver.fujitsu.com/sparcenterprise/manual/

Manual Code C120-E372-03XA

Part No. 875-4049-12

October 2009, Revision A

Fujitsu Welcomes Your Comments

If you have any comments or requests regarding this document, or if you find any unclear statements in the

document, please state your points specifically on the form at the following URL.

For Users in U.S.A., Canada, and Mexico:

http://www.computers.us.fujitsu.com/www/support_servers.shtml?support/servers

For Users in Other Countries:

SPARC Enterprise contact

http://www.fujitsu.com/global/contact/computing/sparce_index.html

Andere Handbücher für SPARC Enterprise T2000

Inhaltsverzeichnis

Andere Fujitsu Server Handbücher

Fujitsu

Fujitsu PRIMERGY TX140 S1p Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Bedienungsanleitung

Fujitsu

Fujitsu SPARC ENTERPRISE T5220 Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 3800E2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Bedienungsanleitung

Fujitsu

Fujitsu Primergy RX200 S4 Bedienungsanleitung

Fujitsu

Fujitsu Primergy CX270 S2 Bedienungsanleitung

Fujitsu

Fujitsu FUTRO S900 Bedienungsanleitung

Fujitsu

Fujitsu Primergy RX100 S3 Betriebsanleitung

Fujitsu

Fujitsu PRIMERGY TX300 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX300 S8 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX150 S6 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY MX130 S1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX4770 M5 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX200FT S2 Leitfaden

Fujitsu

Fujitsu Primergy RX300 S2 Leitfaden

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX2550 M4 Bedienungsanleitung

Fujitsu

Fujitsu Primergy RX300 S3 Leitfaden

Fujitsu

Fujitsu PRIMEPOWER 900 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY Econel 200 S2 Betriebsanleitung

Fujitsu

Fujitsu SPARC Enterprise T5140 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX200 S5 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY CX2550 M1 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung