GE ImageQuant LAS 500 Betriebsanleitung

ImageQuant™LAS 500

Site Preparation Guide

Table of Contents

31 Introduction ..........................................................................................................

52 Site preparation overview ..................................................................................

103 Site preparation checklist ..................................................................................

2 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA

Table of Contents

1 Introduction

Purpose of this document

The purpose of this document is to give the information you need to fully prepare your

site for the installation and testing of the system.

A Site preparation checklist is included in this document.

Scope of this document

This Site Preparation Guide covers the ImageQuant LAS 500 imager.

Preparation

Make sure to read the entire Site Preparation Guide and complete the Site preparation

checklist in Chapter 3.

If GE support is needed, return the completed Site preparation checklist to the GE service

office in your region. You will find E-mail address and fax number to the GE service office

in your region under www.gelifesciences.com/contact. If your region is not listed, select

the nearest region.

ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA 3

1 Introduction

Assign personnel for site

preparation tasks

The site preparation tasks listed in the following table can be divided between two or

three people from the customer.

Site preparation tasksPersonnel

Site preparation/

installation

coordinator

•Review the site preparation guide for safety information and system re-

quirements.

•Choose the site.

•Coordinate personnel and tasks.

•Coordinate the installation timing of the system with any domestic safety

procedures and testings.

•Order required materials.

•Schedule the installation and inform personnel of the installation date.

Laboratory personnel/

Primary users •Review the safety information.

•Make sure that all customer-provided materials for the installation are

present at the site.

Facilities personnel •Make sure that the installation requirements are met for:

-Space at the installation site

-Environmental conditions

-Biosafety

-Ventilation and waste collection

-Electrical supply

-Safety and installation materials

4 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA

1 Introduction

2 Site preparation overview

Introduction

Before the product is delivered, you must prepare the site according to the instructions

in this chapter.

Select the site

Select a site that complies with national and international requirements for biosafety.

WARNING

Spread of biological agents. The operator has to take all necessary

actions to avoid spreading hazardous biological agents. The facility

must comply with the national code of practice for biosafety.

General site requirements

The following requirements must be fulfilled at the location where the ImageQuant LAS

500 imager will be installed:

•There must not be a heat source such as a radiator near the imager

•There must be no risk that the imager can get wet or flooded

•The imager must not be exposed to corrosive gas

•The imager must not be installed in a dusty environment

•The imager must not be installed in a place which is constantly or exessively exposed

to vibration or impacts.

•The imager must not be exposed to direct sunlight

ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA 5

2 Site preparation overview

Space requirements

Prepare a clean working area on a stable laboratory bench. The bench must comply

with the specifications in the following table.

SpecificationParameter

60 x 60 cmMinimum bench area for operating

ImageQuant LAS 500

At least 20 cm free space in front of the

imager.

Free space required around the imager

10 cm free space on all other sides.

490 N (50 kg) or higherLoad capacity

Horizontal ±2°Inclination of bench surface

WARNING

Access to power cord. Do not block access to the power cord. The

power cord must always be easy to disconnect.

There must be additional space on the bench to place samples on the tray.

Note:

6 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA

2 Site preparation overview

Dimensions and weight

The following illustration shows the dimensions of the ImageQuant LAS 500 imager.

570 mm

280 mm

300 mm

The ImageQuant LAS 500 imager weighs 15 kg.

Environmental requirements

ImageQuant LAS 500 is intended for indoor use only.

The installation site must compliy with the following specifications:

SpecificationParameter

18°C to 28°CAmbient temperature, operation

Temperature fluctuation < 10°C per hour

15% to 70% RH, non-condensingRelative humidity, operation

-25°C to 70°CAmbient temperature, transportation/stor-

age

5% to 95% RH, non-condensingAmbient humidity, transportation/storage

ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA 7

2 Site preparation overview

SpecificationParameter

(1) Operating time Oscillation: 0.03G (5 to

60 Hz)

Floor vibration conditions

Impact :1G

(2) Non-operating time Oscillation: 0.4G

(5 to 60 Hz)

Impact :2G

Up to 2000 mAltitude, operation

Pollution degree 2Pollution degree of the environment

CAUTION

Do not use the instrument in a room with a temperature above

+28°C. Higher temperature does not allow the CCD to cool down

properly (to -25°C).

Electrical requirements

SpecificationParameter

100 to 240 V AC ±10%Supply voltage

50/60 HzFrequency

200 WMax power

Overvoltage category IITransient overvoltages

WARNING

Protective ground. The product must always be connected to a

grounded power outlet.

8 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA

2 Site preparation overview

User-supplied accessories and

consumables

The following accessories must be supplied by the user:

Personal Protective Equipment (PPE) as required (gloves, lab coats, etc.).

Other product specifications

SpecificationParameter

70 dB(A) or lowerNoise

Fast Lmax ≤60dB(A), and average Leq ≤ 54dB(A)

(1 m from the instrument)

IP21Protection provided by the enclo-

sure

ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA 9

2 Site preparation overview

3 Site preparation checklist

Introduction

Read the previous chapters in this Site Preparation Guide before completing the checklist.

Complete the checklist in this chapter to make sure that all necessary preparations have

been made for the installation of ImageQuant LAS 500.

Checklist

Comment/specifyN/ANOYESRequirement

General

If GE support is needed for installation, will the GE

service personnel be required to take site EHS

(Environment, Health and Safety) or security

training before doing the installation?

Assigned personnel

Personnel are assigned as specified.

Site selection

Site complies with requirements for

biosafety

General site requirements are fulfilled

Space requirements

Space is available as specified.

Imager

Accessories/additional components

Environmental requirements

The proper environmental conditions are fulfilled

as specified.

Ambient temperature

Relative humidity

10 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA

3 Site preparation checklist

Andere GE Laborausrüstung Handbücher

GE Filter Kit HR 10 Bedienungsanleitung

GE AKTAprime plus Bedienungsanleitung

GE ImageQuant LAS 4000 Bedienungsanleitung

GE AKTApure Bedienungsanleitung

GE SEMIPHOR TRANSPHOR Series Bedienungsanleitung

GE AKTApure Bedienungsanleitung

GE AKTA avant Bedienungsanleitung

GE AKTAprocess Bedienungsanleitung

GE AKTA Prime Plus Bedienungsanleitung

GE 800 Bedienungsanleitung

GE akta start Bedienungsanleitung

GE AKTA avant Bedienungsanleitung

GE MicroCal iTC200 Bedienungsanleitung

GE Amersham Imager 600 Bedienungsanleitung

GE AxiChrom 50 Bedienungsanleitung

GE AKTA GO Bedienungsanleitung

GE LOGIQ S7 Expert Bedienungsanleitung

GE Autosampler Bedienungsanleitung

GE AKTAcrossflow Betriebsanleitung

GE akta start Bedienungsanleitung

GE Tetra EdgeStrip Bedienungsanleitung

GE ReadyToProcess WAVE 25 Bedienungsanleitung

GE Autosampler Bedienungsanleitung

GE OptiSonde Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung