Gefen HDMI-CAT5-144 Bedienungsanleitung

www.gefen.com

1:4 CAT5

Distribution

Amplifier

EXT-HDMI-CAT5-144

User Manual

Technical Support:

Telephone (818) 772-9100

(800) 545-6900

Fax (818) 772-9120

Technical Support Hours:

8:00 AM to 5:00 PM Monday thru Friday.

Write To:

Gefen Inc.

c/o Customer Service

20600 Nordhoff St

Chatsworth, CA 91311

www.gefen.com

[email protected]

Notice

Gefen Inc. reserves the right to make changes in the hardware, packaging and

any accompanying documentation without prior written notice.

1:4 HDMI CAT5 Distribution Ampliﬁer is a trademark of Gefen Inc.

All trademarks are the property of their respective companies

ASKING FOR ASSISTANCE

CONTENTS

1 Introduction

2 Operation Notes

3 Features

4 Sender Panel Descriptions

5 Receiver Panel Descriptions

6 Connecting And Operating The 1:4 HDMI CAT5 DA

7 Manual Equalization Procedure

8 Network Cable Wiring Diagram

9 Speciﬁcations

10 Warranty

Congratulations on your purchase of the 1:4 HDMI CAT5 Distribution Ampliﬁer

DA. Your complete satisfaction is very important to us.

Gefen

Gefen delivers innovative, progressive computer and electronics add-on solutions

that harness integration, extension, distribution and conversion technologies.

Gefen’s reliable, plug-and-play products supplement cross-platform computer

systems, professional audio/video environments and HDTV systems of all sizes

with hard-working solutions that are easy to implement and simple to operate.

The Gefen 1:4 HDMI CAT5 DA

The Gefen 1:4 HDMI Over CAT5 Distribution Ampliﬁer allows you to distribute a

single HDMI video source remotely to as many as 4 separate HDTV displays via

inexpensive and standard CAT5 cables as well as HDMI cables.

How It Works

Simply plug your master video source into the Gefen 1:4 HDMI Over CAT5 DA

sender unit, then run your cables to the remote locations.

If you are using CAT5 cables, pair up your cables with separately purchased

HDMI CAT5 DAR receivers at each video display.

If you are using HDMI cables, just attach up to 4 HDMI cables on the outputs and

connect the other ends to the displays.

After connection of cables, power up (or re-start) all equipment and you will have

effortless HDMI video duplication at all locations.

INTRODUCTION

READ THESE NOTES BEFORE INSTALLING OR

OPERATING THE 1:4 HDMI CAT5 DA

The• 1:4 HDMI CAT5 DA unit is housed in a metal box for better RF shielding.

An HDMI jumper cable (4 are included) must be connected from each of the• lower board outputs to each of the upper board inputs for proper extension

operation.

The maximum cable extension is 300 feet (91 meters) for video resolutions of• 1080i and below.

The maximum cable extension is 150 feet (45 meters) for video resolutions of• 1080p.

Display information (EDID) from the display attached to the HDMI CAT5 DAR• receiver, which is then routed to HDMI output port 1 (lower board), will be sent back

to the source. Therefore, all other displays connected to the receivers at the remote

locations must be capable of accepting the timings and resolutions of the display

that is attached to HDMI output port 1. It is recommended that the display with the

lowest native resolution be connected to HDMI output port 1. This is to ensure that

a compatible video signal will be able to be displayed on all connected monitors.

Shielded CAT6 with metal RJ-45 connectors is recommended to protect from• random ﬂashes caused by EMI.

Extensions under 130 feet can use Auto EQ (which is on by default).• Extensions over 130 feet will require you to manually EQ your signal (see page

5).

Each cable is recommended to be one continuous run from one end to the• other. While wall jacks and punch down blocks can be used, they may cause

degraded performance or unforeseen issues.

Do not use stranded or low/no skew cabling. Solid core cabling should be used• for maximum performance.

HDMI \ HDCP Compliant.•

OPERATION NOTES

Features

HDMI Video Distribution to up to 4 displays•

300 ft. at 1080i; 150-ft range for 1080p•

Maintains high resolution video - beautiful, sharp HDTV resolutions up to• 1080p, 2k, and computer resolutions up to 1920 x 1200 are easily achieved

Enables greater versatility when installing multiple HDMI displays•

HDMI / HDCP compliant•

Package Includes

(1) 1:4 HDMI CAT5 Distribution Ampliﬁer (Sender Unit)

(1) 6 foot HDMI Cable (M-M)

(4) 1 foot HDMI Cable (M-M)

(1) 24V DC power supply

(1) User Manual

FEATURES

Front Panel

Back Panel

HDMI 1

RJ-45 Outputs HDMI 2

RJ-45 Outputs

HDMI 1*

Output

*NOTE: Display information (EDID) is used from whichever display is connected to this port.

Main

HDMI

Input

HDMI 3

Output

Power LED

Indicator

HDMI 2

Output

24V DC Power

Input

HDMI 4

Input

HDMI 3

Input

HDMI 2

Input

HDMI 1

Input

HDMI 4

Output

HDMI 3

RJ-45 Outputs HDMI 4

RJ-45 Outputs

SENDER PANEL DESCRIPTIONS

Front Panel

Back Panel

HDMI Output

VIDEO RJ-45

Port

DDC RJ-45 Port

5V DC

Power input

Power LED

Indicator

EQ trim pot

RECEIVER PANEL DESCRIPTIONS

How to Connect the 1:4 HDMI CAT5 DA

Connect the single HDMI source to the 1:4 HDMI CAT5 DA main HDMI input1. using the supplied 6 foot HDMI cable.

Using the four supplied 1 foot HDMI jumper cables, connect each output on2. the lower portion of the back panel to each of the HDMI inputs on the upper

portion of the 1:4 HDMI CAT5 DA.

Connect the remote displays (up to four) to each of the HDMI CAT5 DAR3. receivers using user supplied HDMI cables.

Connect each of the HDMI CAT54 DAR receivers (up to four) to the 1:44. HDMI CAT5 DA sending unit using a pair of CAT-5, CAT-5e or CAT-6 cables.

NOTE: If ﬁeld terminating network cable, please adhere to the TIA/EIA-568-B

standard. Please see page 8 for more information.

Connect the 5V DC power supply to each of the5. HDMI CAT54 DAR

Receivers.

Connect the included 24V DC power supply to the 1:4 HDMI CAT5 DA.6.

Power on the displays.7.

Power on the source.8.

NOTE: If an image is not being shown on the display, please check all cabling for

proper connections and follow the steps outlined below and in the next section.

The 1:4 HDMI CAT5 DA and HDMI CAT5 DAR receivers have built-in auto

equalization that will automatically tune out any unwanted video noise. This

feature is reliable with premium cable runs up to a maximum of 130 feet. It may

be necessary to disable this feature if there is either no video being displayed on

initial start-up, there is video noise in the image, or the cable run exceeds 130

feet. First, verify that all the proper connections have been made and that all

devices are powered on before attempting to disable auto equalization. Please

follow the section on the next page to manually equalize the video signal.

1:4 HDMI CAT5 DA CONFIGURATION

CONNECTING AND OPERATING THE 1:4 HDMI CAT5 DA

MANUAL EQUALIZATION PROCEDURE

The HDMI CAT5 DAR receiver units have a set of dip switches located on the

underside of their casings. There is a piece of silver metallic tape that must be

removed to expose these dip switches. Each HDMI CAT5 DAR receiver carries

one bank of 4 dip switches. All dip switches on the HDMI CAT5 DAR receiving

units are used in this procedure. Dip switches 1 relates to the Auto Equalization

function, while dip switches 3 and 4 control the boost strength from the 1:4

HDMI CAT5 sending unit. By default, all dip switches on the HDMI CAT5 DAR

should be in the OFF position. To turn off auto equalization, turn dip switch 1 on

the receiving units to the ON position (Auto EQ off). With these settings, please

follow the steps below to equalize the picture.

Insert a small ﬂat head tool into the trim pot on the receiver unit.1.

Turn the trim pot in a clockwise fashion until it comes to a stop. Do not force2. the trim pot beyond this point. Doing so may render the trim pot useless.

Slowly turn the trim pot counter-clockwise in millimeter increments until the3. image stabilizes and all video noise disappears.

Carefully remove the adjustment tool.4.

NOTE: If your cable run is beyond 130 feet, or the steps above do not produce

any video, it may be necessary to increase the boost from the sending unit. Use

the chart below to increase the senders boost strength by changing the HDMI

CAT5 DAR receiver’s dip switches. Once a new boost setting is set, repeat steps

1 through 4 from above. The required boost setting will largely be dependant

on the quality and length of cabling. Experiment with all boost settings until the

image stabilizes and all video noise has been eliminated.

Receiver Auto EQ Dip Switch Settings

Setting Switch 1 Switch 2

Manual EQ ON Not Used

Auto EQ (Default) OFF Not Used

Receiver Boost Dip Switch Settings

Setting Switch 3 Switch 4

No Boost (Default) OFF OFF

Medium Boost OFF ON

High Boost ON OFF

Very Low Boost ON ON

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gefen Verstärker Handbücher

Gefen

Gefen COMPAUD-148 Bedienungsanleitung

Gefen

Gefen 1x8 DVI DA Bedienungsanleitung

Gefen

Gefen EXT-VGA-CAT5-148S Bedienungsanleitung

Gefen

Gefen COMPAUD-CAT5-144 Bedienungsanleitung

Gefen

Gefen VDX-600 Bedienungsanleitung

Gefen

Gefen AUD-148 Bedienungsanleitung

Gefen

Gefen EXT-DVI-141DLBP Bedienungsanleitung

Gefen

Gefen EXT-HDMI1.3-1410-BLK Bedienungsanleitung

Gefen

Gefen EXT-HDMI-CAT5-148 Bedienungsanleitung

Gefen

Gefen HDMI-248 Bedienungsanleitung

Gefen

Gefen COMPAUD-143 Bedienungsanleitung

Gefen

Gefen EXT-COMPAUD-143 Bedienungsanleitung

Gefen

Gefen ex tend it VDX 600 Bedienungsanleitung

Gefen

Gefen EXT-HDMI-CAT5-144 Bedienungsanleitung

Gefen

Gefen EXT-HDMI-144 Bedienungsanleitung

Gefen

Gefen HDMI-CAT5-148 Bedienungsanleitung

Gefen

Gefen 1:4 HDMI CAT5 Bedienungsanleitung

Gefen

Gefen EXT-HDMI-144 Bedienungsanleitung

Gefen

Gefen EXT-VGA-CAT5-148S Bedienungsanleitung

Gefen

Gefen 2x8 DVI DA Bedienungsanleitung

Gefen

Gefen EXT-DVI-148 Bedienungsanleitung

Gefen

Gefen DVI DL Splitter Bedienungsanleitung

Gefen

Gefen EXT-COMPAUD-143 Bedienungsanleitung

Gefen

Gefen EXT-UHD600A-44 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung