Generac Power Systems 1043-2 Bedienungsanleitung

2700PSI

The Reliable Ones

High Pressure Washer

Owners Manual

Problems?

Questions?

Before taking your unit

back to the store,

call the pressure washer

helpline at

1-800-2 0-1408

M-F 8-5 CST

This pressure

washer is

equipped with an

Automatic Cool

Down System.

See page 12 for

details

GENERAC

This symbol points out important safety instructions, which, if not followed, could

endanger the personal safety and/or property of yourself and others. Read and follow

all instructions in the manual before attempting to operate this unit.

Model No. 10432 (2 00 PSI High Pressure Washer) Manual No. B3241 Revision 0 ( /8/98)

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug

to prevent accidental starting when setting up, transporting, adjusting or making repairs to your

high pressure washer.

 Engine exhaust gases contain DEADLY carbon

monoxi e gas. This angerous gas, if breathe

in sufficient concentrations, can cause

unconsciousness or even eath. Operate this

equipment only in the open air where a equate

ventilation is available.

 Gasoline is highly FLAMMABLE an its vapors

are EXPLOSIVE. Do not permit smoking, open

flames, sparks or heat in the vicinity while

han ling gasoline. Avoi spilling gasoline on a hot

engine. Allow unit to cool for 2 minutes before

refueling. Comply with all laws regulating storage

an han ling of gasoline.

 Use this pressure washer in areas away from

combustible materials, combustible fumes or

ust.

 The high pressure equipment is esigne to be

use with Generac authorize parts only. If you

use this equipment with parts that o not comply

with minimum specifications, the user assumes

all risks an liabilities.

 Some chemicals or etergents may be harmful

if inhale or ingeste , causing severe nausea,

fainting or poisoning.

 Do not allow CHILDREN to operate the pressure

washer at any time.

 Operate engine only at governe spee . Running

the engine at excessive spee s increases the

hazar of personal injury. Do not tamper with

parts which may increase or ecrease the

governe spee .

 Do not wear loose clothing, jewelry or anything

that may be caught in the starter or other rotating

parts.

 Before starting the pressure washer in col

weather, check all parts of the equipment an be

sure ice has not forme there.

 Units with broken or missing parts, or without

protective housing or covers shoul NEVER be

operate .

 The muffler an air cleaner must be installe an

in goo con ition before operating the pressure

washer. These components act as spark arrestors

if the engine backfires.

 Check the fuel system for leaks or signs of

eterioration such as chafe or spongy hose,

loose or missing clamps or amage tank or cap.

Correct all efects before operating the pressure

washer.

 Do not spray flammable liqui s.

 Never aim the gun at people, animals or plants.

 The high pressure stream of water that this

equipment pro uces can pierce skin an its

un erlying tissues, lea ing to serious injury.

 High pressure spray can cause paint chips or

other particles to become airborne an fly at high

spee s.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects, or other reproductive harm.

WWAARRNNIINNGG::

Important!  Safety Rules  Important!

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

 Always wear eye protection when you use this

equipment or when you are in the vicinity where

the equipment is in use.

 Never move the machine by pulling on the high

pressure hose. Use the han le provi e on the

top of the unit.

 Always be certain the spray gun, nozzles an

accessories are correctly attache .

 Never use a spray gun which oes not have a

trigger lock or trigger guar in place an in working

or er.

 Use a respirator or mask whenever there is a

chance that vapors may be inhale . Rea all

instructions with the mask so you are certain it

will provi e the necessary protection against

inhaling harmful vapors.

 High pressure spray may amage fragile items

inclu ing glass. Do not point spray gun at glass

when in the high pressure spray mo e.

 Keep the hose connecte to machine an the

spray gun while the system is pressurize .

Disconnecting the hose while the unit is

pressurize is angerous.

 Hol the spray gun firmly in your han s before

you start the unit. Failure to o so coul result in

an injury from a whipping spray gun. Do not leave

the spray gun unatten e while the machine is

running.

 The cleaning area shoul have a equate slopes

an rainage to re uce the possibility of a fall ue

to slippery surfaces.

 Keep water spray away from electric wiring or fatal

electric shock may result.

 Do not secure trigger gun in the pull-back (open)

position.

 Do not by-pass any safety evice on this machine.

 The muffler an engine heat up uring operation

an remain hot imme iately after shutting it own.

Avoi contact with a hot muffler or engine or you

coul be severely burne .

 Operate an store this unit on a stable surface.

 Never allow any part of the bo y to come in

contact with the flui stream. DO NOT come in

contact with a flui stream create by a leak in

the high pressure hose.

 High pressure hose can evelop leaks from wear,

kinking, abuse, etc. Water spraying from a leak

is capable of injecting material into skin. Inspect

hose each time before using it. Check all hoses

for cuts, leaks, abrasions or bulging of cover, or

amage or movement of couplings. If any of

these con itions exist, replace hose imme iately.

Never repair high pressure hose. Replace it with

another hose that meets minimum pressure rating

of your pressure washer.

Important!  Safety Rules  Important!

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

CONGRATULATIONS on your purchase of a

GENERAC high pressure washer. It has been

esigne , engineere an manufacture to give you

the best possible epen ability an performance.

Shoul you experience any problem you cannot

easily reme y, please contact your nearest

GENERAC Authorize Service facility, or call the 1-

800 number liste on the front of this manual. We

have competent, well-traine technicians an the

proper tools to service or repair this unit.

Please rea an retain this manual. The instructions

will enable you to assemble an maintain your high

pressure washer properly.

CUSTOMER

RESPONSIBILITIES

 Rea an observe the safety rules.

 Follow regular sche ule in maintaining, caring for

an using your high pressure washer.

 Follow the instructions un er Customer

Responsibilities an Storage sections of this

Owner's Manual.

PRODUCT

SPECIFICATIONS

Pressure Washer Specifications

Outlet Pressure . . . . 2700 psi

Flow Rate . . . . . . . . . 2.5 gallons per minute (gpm)

Detergent Mix . . . . . . Use un ilute etergent

approve for pressure

washers

Water Supply . . . . . . Not to excee 140°F

Temperature

Automatic Cool . . . . Will cycle when water

Down System reaches 140°-145°F

Engine specifications

Engine Model . . . . . . GN-220

Rated Horsepower . . 7.8

Displacement . . . . . . 220cc

Spark Plug

Type . . . . . . . . RC-12YC

Set Gap To: . . 0.030 inch (0.76mm)

Gasoline Capacity . . 4.2 U.S. quarts

Oil . . . . . . . . . . . . . . . SAE 30

In the State of California a spark arrestor is require

by law (Section 4442 of the California Public

Resources Co e). Other states may have similar

laws. Fe eral laws apply on fe eral lan s.

NOTE: The spark arrestor must be maintaine in

effective working or er by the owner/operator.

You can or er a replacement spark arrestor through

your authorize Generac service facility. See Engine

Owners Manual for part number.

Model Number 1043-2

Serial Number

Date of Purchase

The mo el an serial numbers will be foun on a

ecal attache to the pressure washer. recor both

serial number an ate of purchase an keep in a

safe place for future reference.

KNOW YOUR PRESSURE WASHER

Read this owners manual and safety rules before operating your high pressure washer.

Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various

controls an a justments. Save this manual for future reference.

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

Pump  Develops high pressure.

Spray Gun  Controls the application of water an

chemical onto cleaning surface with trigger evice.

Inclu es safety latch.

Chemical Valve Handle  The han le allows you to

select the high pressure spray or the chemical spray

(locate on the wan ).

Dual Element Air Cleaner  Uses a ry type filter

element an foam pre-cleaner to limit the amount of

irt an ust that gets in the engine.

Water Inlet  Connection for gar en hose.

Dual Lance  Must be connecte to the spray gun.

High Pressure Hose  Connect one en to water

pump an the other en to spray wan .

High Pressure Outlet  Connection for high pressure

hose.

Spark Arrestor Muffler  Exhaust muffler lowers

engine noise an is equippe with a spark arrestor

screen, a USDA man ate for engine use in national

forests an parks.

Goggles  Always use the enclose goggles or other

eye protection when running your pressure washer.

Automatic Cool Down System  Cycles water

through pump when water reaches 140°-145°F. Warm

water will discharge from pump onto base of unit.

This system prevents internal pump damage.

Gas Tank  Fill with regular unlea e gasoline.

Chemical Concentration Knob  A just concentra-

tion of chemical here.

Pressure Control Knob  A just pressure output

here.

Primer Bulb  Use for starting a col engine.

Spray Gun

Chemical Valve Handle

High Pressure Hose

Goggles

Dual Element

Air Cleaner

Gas Tank

Water Inlet

Pump equippe with

Automatic Cool Down System

High Pressure Outlet

Pressure Control

Knob

Spark Arrestor

Muffler

Primer Bulb

Dual Lance

Chemical

Concentration Knob

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

Rea entire owners manual before you attempt to

assemble or operate your new pressure washer.

Your new pressure washer has been assemble at

the factory with the exception of those parts left

unassemble for shipping purposes.

REMOVE PRESSURE

WASHER FROM CARTON

 Remove parts box inclu e with pressure washer.

 Slice two corners at gui e han le en of carton

from top to bottom so the panel can be fol e own

flat, then remove all packing material.

 Roll pressure washer out of carton.

CARTON CONTENTS

Items in the carton inclu e:

 Main Unit

 Manual Bag

 Owners Manual

 Engine Owners Manual

 Nozzle Cleaning Kit

 ORing Maintenance Kit

 Parts Box (which inclu es the following):

 Vi eo

 Wireform

 Goggles

 Spray Gun

 Dual Lance

 High Pressure Hose

 Han le

 Han le Parts Bag (which inclu es the following):

 2 carriage bolts

 2 knobs

If any of the above parts are missing or amage , call

the pressure washer helpline at 18002 01408.

PREPARING THE

PRESSURE WASHER

FOR USE

If you have any problems with the assembly of your

pressure washer or if parts are missing or amage ,

call the Pressure Washer Helpline at 1-800-2 0-1408.

To prepare your pressure washer for operation you

will nee to perform these tasks:

 Attach the han le an attach the wire form that

hol s high pressure hose an spray gun.

 Connect high pressure hose to the spray gun an

the pump an connect water supply to the pump.

 A oil to engine crankcase.

 A fuel to fuel tank.

Attach the Handle

 Place the han le onto the bottom the han le

supports alrea y connecte to the main unit. Make

sure the holes in the han le align with the holes in

the han le supports (Figure 1).

Note: It may be necessary to move the han le

supports from si e to si e in or er to align the han le

so it will sli e over the han le supports.

Figure 1 — Attach the top of the handle to the

bottom of the handle.

Make sure

the holes in

the handle

supports

are aligned

with the

holes in the

handle.

Handle

Supports

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

 Insert the carriage bolts from the outsi e through

the holes on the han le an attach the plastic

knobs on the insi e. Tighten the knobs by han

(Figure 2).



Insert the wire support with the longer arm positione

on the left. From this view (from rear of unit), the hook

resembles a J

(Figure 3)

Add Engine Oil

IMPORTANT: Any attempt to crank or start the

engine before being properly service with the

recommen e oil will result in an engine failure.

Note: When a ing oil to the engine crankcase, use

only high quality etergent oil rate with API service

classification SF,SG, SH or SH/CD rate SAE 30

weight. Select the oils viscosity gra e accor ing to

your expecte operating temperature. Do Not Use

SAE 10W40 Oil.

Although multi-viscosity oils (5W30, 10W30, etc.)

improve starting in col weather, these multi-viscosity

oils will result in increase oil consumption when use

above 32°F. Check your engine oil level more

frequently to avoi possible amage from running

low on oil.

 Place pressure washer on a level surface.

 Clean area aroun oil fill an remove yellow oil fill

cap (Figure 4).

 Pour oil into the oil fill opening until it reaches the

top of the oil fill hole. DO NOT OVERFILL.

 Install yellow oil cap, han tighten securely.

Note: Check Oil Often During Engine Breakin.

Add Gasoline

DANGER! Never fill fuel tank indoors.

Never fill fuel tank when engine is running

or hot. Do not smoke when filling fuel tank.

WARNING! Never fill fuel tank completely

full. Fill tank to about 1/2" below the bottom

of the filler neck to provide space for fuel

expansion. Wipe away any fuel spillage

from engine and equipment before starting.

The manufacturer recommen s fresh, clean unlea e

automotive gasoline.

 Use clean fuel an store in approve containers.

Use clean fill funnels. Never use stale gasoline

left over from last season or gasoline store for long

perio s.

Figure 3 — Fit wire form on handle.

Figure 4 — Add oil to engine crankcase. Do not

attempt to start engine without

adding oil.

Figure 2 — Insert the carriage bolts and attach

the knobs.

col er 32°F warmer

5W30 SAE 30

Yellow

Oil Fill Cap

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

 Clean area aroun fuel fill cap. Remove cap

(Figure 5).

 A UNLEADED gasoline, slowly, to fuel tank.

Use a funnel to prevent spillage.

 Install fuel cap an wipe up any spille gasoline.

Connect Hose and Water

Supply to Pump

IMPORTANT: You must assemble wan an attach

all hoses before you start engine. Starting engine

without all hoses connecte an water supplie will

amage pump.

 Uncoil high pressure hose an attach the en of the

hose with the threa e en to the base of the spray

gun (Figure 6). Tighten by han .

 Attach other en of high pressure hose to the high

pressure outlet on the pump (Figure 7). Tighten by

han .

 Before you connect your gar en hose to the water

inlet, inspect the water inlet screen (see Figure 8).

Clean the screen if it contains ebris or have it

replace if amage . Do not run the pressure

washer if the water inlet screen is damaged.

 Connect gar en hose to water inlet. Tighten firmly

by han (Figure 8).

 Turn on the water (open valve completely).

 Squeeze trigger on gun to purge pump system of

air an impurities. Squeeze until a stea y stream

appears.

Figure 7 — Connect high pressure hose to

pump.

Figure 6 — Connect high pressure hose

to spray gun.

Figure 8 — Connect the garden hose to water

inlet and turn ON the water.

Figure 5 — Add gasoline to fuel tank.

Gas Cap

Connect High Pressure

Hose Here

Connect Garden

hose here.

Check Screen

for Damage.

Connect high

pressure hose

here

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

WARNING! Before starting the pressure

washer, be sure you are wearing adequate

eye protection.

 Attach ual lance to spray gun. Tighten by han

(Figure 9).

CHECKLIST BEFORE

STARTING ENGINE

If you have reache this point, look back over the

assembly to see if you have performe all of the

following.

 Check for properly tightene hose connections

(high pressure an water supply) an for tight

connections an that there are no kinks, cuts, or

amage to the high pressure hose, or gar en hose.

 Check that oil has been a e to proper level in

engine crankcase before trying to start the pressure

washer.

 A proper gasoline to fuel tank.

 Provi e proper water supply (not to excee 140°F).

 Be sure to rea Safety Rules an Operation

sections before using the pressure washer.

Figure 9 — Connect nozzle extension to spray

gun.

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

HOW TO USE YOUR

PRESSURE WASHER

If you have any problems operating your pressure

washer, please call the pressure washer helpline at

1-800-2 0-1408.

How to Start Your Engine

The best way to start your engine-powere pressure

washer for the first time is to follow these instructions

step-by-step. This starting information also applies

whenever you start the engine after you have let the

pressure washer sit i le for at least a ay.

 This pressure washer requires a water source that

flows at least 2.5 gallons per minute. Do not attempt

to siphon water from a non-pressurize container.

Place the pressure washer close enough to an

outsi e water source so that no more than 50' of

gar en hose is nee e .

 Check that the high pressure hose is tightly

connecte to the spray gun an to the pump. See

ASSEMBLY section for illustrations.

 Connect the gar en hose to water inlet on the

pressure washer pump an turn the water valve on

all the way.

IMPORTANT: Do not run pump without the water

supply connecte an turne on. You must follow this

caution or the pump will be amage .

 Place the Run/Stop switch to Run.

 Press the primer bulb 3 times, waiting 2 secon s

between each push

Note: For a warm engine, o not prime.

 Squeeze the trigger on the spray gun to relieve air

pressure cause by turning on the water. Water will

spew out the gun in a thin stream. Continue to hol

trigger until you have a stea y stream of water an

no air remains.This will make it easier to pull start

the engine. Release the trigger.

 Apply the safety latch to the spray gun trigger

(Figure 11).

 Grasp rope han le an pull slowly until you feel

some resistance. Then pull cor rapi ly to

overcome compression, prevent kickback an start

the engine. Let rope return to starter slowly.

If after 3 pulls the engine fails to start, isengage the

spray gun safety latch, squeeze the trigger to relieve

water pressure, re-engage the spray gun safety latch

an pull the recoil starter han le rapi ly (Max. 3

pulls).

How to Stop Your Pressure

Washer

 Move the Run/Stop switch to Stop.

 Simply shutting off the engine will not release

pressure in the system. Squeeze trigger on the

spray gun to relieve pressure in the hose.

Note: A small amount of water will squirt out when

you release the pressure.

Figure 11 — Safety Latch.

Safety Latch On

Dieses Handbuch passt für folgende Modelle

Andere Generac Power Systems Hochdruckreiniger Handbücher

Generac Power Systems

Generac Power Systems 1300PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1439-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1195-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Power Washer Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1046-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1293-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Power Washer Bedienungsanleitung

Generac Power Systems

Generac Power Systems OneWASH Bedienungsanleitung

Generac Power Systems

Generac Power Systems 6020-2 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1292-2 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 4040 PRO GAS PW 49ST Bedienungsanleitung

Generac Power Systems

Generac Power Systems 3000PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 2600 PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems OneWASH Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1173-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1417-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Power Washer Bedienungsanleitung

Generac Power Systems

Generac Power Systems 006022-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 4240 PRO GAS PW 49ST EPA III Bedienungsanleitung

Generac Power Systems

Generac Power Systems 2100PSI 1974-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1455-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 10000025895 Bedienungsanleitung

Generac Power Systems

Generac Power Systems The Reliable Ones Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1293-2 Bedienungsanleitung

Beliebte Hochdruckreiniger Handbücher anderer Marken

Shark

Shark RG-232637 Bedienungsanleitung

Shakti Technology

Shakti Technology S3 Bedienungsanleitung

Kärcher

Kärcher K 4 Pure Bedienungsanleitung

Porter-Cable

Porter-Cable D25806-025-2 Bedienungsanleitung

REM POWER

REM POWER HDEm 662 Bedienungsanleitung

Landa

Landa HS-3000 Bedienungsanleitung

Craftsman

Craftsman 580.752270 Bedienungsanleitung

HIKOKI

HIKOKI AW 100 Bedienungsanleitung

Delco

Delco DC 1302 Bedienungsanleitung

Kärcher

Kärcher K 3 Full Control Bedienungsanleitung

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Bedienungsanleitung

ARKSEN

ARKSEN 014-HG-14141-HR Bedienungsanleitung

Black & Decker

Black & Decker PW1700SPX Bedienungsanleitung

Kärcher

Kärcher 595 - SPARE Leitfaden

Kranzle

Kranzle B 10 200 Bedienungsanleitung

Stihl

Stihl RE 90 Bedienungsanleitung

PowR-Quip

PowR-Quip PQ-2600 Bedienungsanleitung

Hotsy

Hotsy 5645 Bedienungsanleitung