Gofanco HDMIExt4P Bedienungsanleitung

4-Port HDMI Extender/Splitter

over CAT5e/6 with IR - 40M

G4-0022A

P/N: HDMIExt4P

Congratulationsforowningagofancoproduct.Ourproducts

aim to meet all your connectivity needs wherever you go.

Have fun with our products!

Please read this manual carefully before first use.

If you need more information about our products, please

visit www.gofanco.com.

For technical support, please email us at support@gofanco.

com.

For drivers/manuals download, please go to http:// www.

gofanco.com/download.

Introduction

gofanco 4-Port HDMI Extender/Splitter over CAT5e/6 with IR

- 40M (part# HDMIExt4P) extends HDMI signals to four

monitors over Cat5e/6 up to 40m with 1080p.

Specifications

Package Contents

• 4-Port HDMI Extender/Splitter over CAT5e/6 with IR -

40M (1x TX & 4x RXs)

• 5x Power adapters

• IR Blaster extension cable & IR Receiver extension cables

• Screw kit

• User's guide

Output Signal HDMI

Protocol HDbitT

Resolution Up to 1080p

Transmission

Distance Up to 40m (130ft)

Network Cable CAT5e/6

(CAT6 recommended)

HDMI Cable Up to 5m (Input & Output)

Power Supply TX: DC 5V/3A, RX: DC 5V/1A

IR Signal 20~60KHz IR devices supported

•Power Jack: Connect the included 5V/3A DC power

adapter here

•EDID : The HDMI source device reads EDID information

from the TX unit, and outputs it to the RXs.

Please refer to the settings below.

Layout

Power Jack

Figure 1: Transmitter (TX)

HDMI In

IR Out

RJ45

* 6: Default setting

EDID RJ45

Figure 2: Transmitter (TX)

Link LED

•Link LED: Turns red when powered. Turns blue when

there is an HDMI signal detected

•Reset: Press to reset if HDMI Extender doesn't work

properly

•IR Out: Infrared 3.5mm socket. Plug IR Blaster extension

cable here. See instructions on page 7.

•RJ45 (1): Link to Receiver 1's RJ45 via a Cat5e/6 cable

•RJ45 (2): Link to Receiver 2's RJ45 via a Cat5e/6 cable

•HDMI In: Connect your HDMI source here with an HDMI

cable (cable not included)

•RJ45 (3): Link to Receiver 3's RJ45 via a Cat5e/6 cable

•RJ45 (4): Link to Receiver 4's RJ45 via a Cat5e/6 cable

Reset

Power jack

•Power Jack: Connect the included 5V/1A DC power

adapter here

•HDMI Out: Connect your HDMI display here with an

HDMI cable (cable not included)

•IR In: Infrared 3.5mm socket. Plug IR Receiver extension

cable here. See instructions on page 7.

IR InHDMI Out

Figure 4: Receiver (RX) - HDMI Display Output

Reset

•Reset: Press to reset if HDMI Extender doesn't work

properly

•RJ45: Link to the Transmitter's RJ45 via a Cat5e/6 cable

•Link LED: Blinks when powered on. ON when the Cat5e/

6 cable is connected/linked properly between the

Transmitter and Receiver

Figure 3: Receiver (RX) - RJ45 Input

RJ45 Link LED

IR Extenders

•IR Blaster: Plug into the Transmitter's IR 3.5 socket to

emit IR signals.

•IR Receiver: Plug into the Receiver's IR 3.5 socket to

receive IR signals from a remote control (for the HDMI

device connected to the Transmitter).

Note: Incorrect placement of the IR Blaster and IR

Receiver may result in failure of these cables. Please

check carefully before plugging in the IR cables to

proper IR sockets.

Figure 5: IR Blaster

(Connect to Transmitter TX)

Figure 6: IR Receiver

(Connect to Receiver RX)

Hardware Installation

Note: To achieve optimal performance, CAT6 cable is

recommended.

1. Power off all devices including your HDMI source and

display.

2. Connect your HDMI source to the Transmitter's HDMI

IN connector.

3. Optional: Connect the IR Blaster extension cable to the

Transmitter's IR Out. Face the eye towards your HDMI

device's IR window.

4. Connect your HDMI display to the Receiver's HDMI OUT

connector with an HDMI cable (not included). Repeat

this step for all Receivers.

5. Optional: Connect the IR Receiver extension cable to the

Receiver's IR In. Repeat this step for all Receivers.

6. Switch the EDID according to your desired HDMI signal

format. Refer to page 4 for details.

7. Connect and link the Transmitter and Receivers by

CAT5e/6 cables.

8. Plug the included power adapters into the Transmitter's

and Receivers' Power Jacks, then plug all power

adapters into reliable power outlets.

9. Power on your HDMI device and HDMI displays.

10. The HDMI Extender is ready for use.

Application

Easily extends HDMI signals such as DVD players or

computers to four remote displays simultaneously . An

ideal solution for exhibitions, video conferences, show

centers, and etc..

HDMI IN

Figure 7

* When using the remote control, please make sure its

distance to the IR Receiver extension cable is within 5

meters (16.4 ft) and without obstructions.

CAT5e/6 cable

FAQ & Solutions

Q: There is no picture on the TVs:

A: 1) Check whether the correct TV input is selected.

2) Check whether the "Link" LED on TX and RXs are on.

If the RX's Link LED blinks, it means the RX doesn't receive

signals from the TX.

3) Make sure the resolution of the input HDMI source is

supported by this Extender/Splitter.

Q: There is unstable picture on the TVs:

A: 1) Switch the "EDID" to the appropriate position, refer to

page 4 for details.

2) Unplug the Cat5e/6 cable and plug in again.

If the issue still exists, use other Cat5e/6 cables.

Q: Only one TV has image:

A: 1) Make sure the CAT cables and HDMI cable are

connected correctly and securely.

2) Press the "Reset" button on the TX to re-identify the

HDMI signal.

3) Unplug the Cat5e/6 cable and plug in again.

Inhaltsverzeichnis

Andere gofanco Extender Handbücher

gofanco

gofanco 4K120 Bedienungsanleitung

gofanco

gofanco HDwireless10x1 Bedienungsanleitung

gofanco

gofanco HD14Ext-2P Bedienungsanleitung

gofanco

gofanco HD20wireless Bedienungsanleitung

gofanco

gofanco HDBaseT-HD20 Bedienungsanleitung

gofanco

gofanco KVMHDExt Bedienungsanleitung

gofanco

gofanco HDExt70 Bedienungsanleitung

gofanco

gofanco HDbaseT-HDR Bedienungsanleitung

gofanco

gofanco HDWirelessKVM Bedienungsanleitung

gofanco

gofanco HDExtIP4K Bedienungsanleitung

gofanco

gofanco Prophecy PRO-HDExtIP-TX Bedienungsanleitung

gofanco

gofanco KVMHD20Ext Bedienungsanleitung

gofanco

gofanco G4-0014A Bedienungsanleitung

gofanco

gofanco HD20Ext1xN Bedienungsanleitung

gofanco

gofanco HDBaseT4P-4K Bedienungsanleitung

gofanco

gofanco HDExt50 Bedienungsanleitung

gofanco

gofanco HDMIExtSplit Bedienungsanleitung

gofanco

gofanco HDbitTPro Bedienungsanleitung

gofanco

gofanco HDwireless100-LT Bedienungsanleitung

gofanco

gofanco HDwireless100 Bedienungsanleitung

gofanco

gofanco AudioCATExt Bedienungsanleitung

gofanco

gofanco HDExt Bedienungsanleitung

gofanco

gofanco HD14Ext-EDID Bedienungsanleitung

gofanco

gofanco HD14Ext1xN Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

gofanco HDMIExt4P Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken