gofanco HDMIExt8P Bedienungsanleitung
8-Port HDMI Extender/
Splitter over CAT5e/6 with
Loopout - 40m
User's Guide
G4-0052A
P/N:HDMIExt8P
2
Thank you for purchasing from gofanco. Our products
aim to meet all your connectivity needs wherever you
go. For optimum performance and safety, please read
the instructions carefully and keep this User's Guide for
future reference. If you need more information about
our products, please visit www.gofanco.com. For
For drivers/manuals download, please go to http://
www.gofanco.com/download.
Important Safety Notices
Pleasereadsafetyinstructionscarefullybeforeinstallation
and operation.
• Please pay close attention to all warnings and hints
for this device
• Do not expose this unit to rain, heavy moisture, or
liquid
• Do not put any items into the device or attempt to
modify its operation
• Do not repair the device or open the enclosure
without professional guidance to avoid electric
shocks. Doing so may void your warranty
• Keep the product in a well-ventilated location to
avoid damage from overheating
• Shut off power and make sure environment is safe
before installation
• Do not plug the HDMI cables and IR cables
in/out when the device is in use to avoid cable
damage. Make sure they are plugged into the
correct ports
• Use the included power adapters only. Make sure
the specification matches if using 3rd-party DC
power adapters
3
Introduction
The 8-Port HDMI Extender/Splitter over CAT5e/6 with
Looput - 40m extends 1080p signals to 8 monitors over
CAT5e/6 up to 40m.
PackageContents
Transmitter (1pc)
Power Adapter
12V/2A (1pc)
Power Adapter
5V/1A (8pcs)
IR Blaster Extension
Cable (1pc)
Manual (1pc)
Receiver (8pcs)
IR Receiver Extension
Cable (1pc)
4
Product Layout
Figure 1: Transmitter (TX) - Back Panel
1PowerJack:Connecttheincluded12VDC/2Apower
adapter here
2EDID: The HDMI source device reads EDID
information from the TX unit, and outputs it to the
RXs. Please refer to the setting below.
3IR Out: Infrared 3.5mm socket. Plug IR Blaster
Extension Cable here. See instruction on page 7.
4HDMI In: Connect your HDMI source here with an
HDMI cable (cable not included)
5HDMI Out: Connect your HDMI display here for
local monitoring of the HDMI displays
6RJ45 Out: Link to Receiver's RJ45 In using a Cat5e/
6 cable
*Default setting
5
Figure 3: Receiver (RX) - Input
Figure 2: Transmitter (TX) Front Panel
7Link LED: Turns red when powered. Turns blue
when there is an HDMI signal detected
8Reset: Press to reset if HDMI Extender doesn't work
properly
1 Reset: Press to reset if HDMI Extender doesn't work
properly
2 RJ45 In: Link to the Transmitter's RJ45 Out via a
Cat5e/6 cable
3 Link LED: Blinks when powered on. On when the
Cat cable is connected/linked properly between
the Transmitter and receiver
6
Figure 4: Receiver (RX) - HDMI Output
4 Power Jack: Connect the included 5VDC power
adapter here
5 HDMI Out: Connect your HDMI display here with
an HDMI cable (cable not included)
6 IR In: Infrared 3.5mm socket. Plug IR Receiver
Extension Cable here. See instructions on page 7.
Installation Requirements
1. HDMI source device (DVD player, set top box, PC,
etc.)
2. HDMI display device (SDTV/Monitor, HDTV/
Monitor, projector, etc.)
3. HDMI cables (not included)
4. UTP/STP CAT5e/6/6A/7 cable, following
IEEE-568B wiring standard
7
Hardware Installation
To achieve optimal performance, Cat6 cable is
recommended.
1. Power off all devices including your HDMI source
and HDMI display.
2. Connect your HDMI source to the Transmitter's
HDMI In connector.
3. Connect your HDMI display to the Transmitter's
HDMI Out. This connection is optional and need
only when local monitoring of the local display is
required.
4. Optional: Connect the IR Blaster Extension Cable
to the Transmitter's IR Out port. Face the eye
towards your HDMI source device's IR window.
This connection is needed only if you need to
control your HDMI source at the remote location.
5. PlugyourCat5e/6 cable betweenthe Transmitter's
RJ45 Out and Receiver's RJ45 In.
6. Connect your HDMI display to the Receiver's
HDMI Output connector with an HDMI cable
(HDMI cable not included).
7. Optional: Connect the IR Receiver Extension Cable
to the Receiver's IR In port. This connection is
needed only if you need to control your HDMI
source at the remote location.
8. Plug the included 12V power adapter into the
Transmitter's Power Jack.
9. Plug the included 5V power adapter into the
Receiver's Power Jack, then plug all power
adapters into reliable power outlets.
10. Power on your HDMI source device and HDMI
displays. The extender is ready for use.
8
ConnectionDiagram
Note: Please use the IR remote control to control
only one Receiver at a time to avoid interference.
Transmitter
9
FAQ & Solutions
Q1: No image or audio output on the display?
A: 1. Check if the display is in standby mode.
2. Make sure the display's HDMI port is properly
connected to the HDMI cable.
3. Check the Link LED indicator on the Receiver is
on. This flashing LED means the RX is not receiving
signal from the transmitter.
4. Check the Link LED indicator on the Transmitter
is blue. A red color LED means there is no signal
from the source device.
5. Check whether the input resolution is support by
this product.
Q2: Not all displays are receiving a signal.
A: 1. Check the Cat5e/6 cable for secure and solid
connection.
2. Press the Reset button on the Transmitter and
Receiver to reset the system.
3. Re-connect the Cat5e/6 cable(s) corresponding to
the display(s) that are not working properly.
10
Specifications
Item Specification
HDMI signal HDMI 1.3, HDCP 1.2
Input 1x, 19-pin HDMI, Female
Output 8x RJ45, 1x HDMI
Resolution
480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz, 1080p@50/60Hz
Transmission distance Up to 130 ft (40m)
IR signal 20KHz - 60KHz
Operating temperature 32 F - 140 F (0 - 60 C)
Power adapter TX: 12VDC/2A
RX: 5VDC/1A
Power consumption TX: <15W
RX: <2W
Dimensions TX: 10.9" (L) x 2.6" (W) x 0.98" (H)
RX: 2.8" (L) x 2.6" (W) x 0.98" (H)
Weight TX: 1.37 lbs
RX: 0.18 lbs (each)
Inhaltsverzeichnis
Andere gofanco Extender Handbücher
gofanco
gofanco HD14Ext-2P Bedienungsanleitung
gofanco
gofanco HDwireless200 Bedienungsanleitung
gofanco
gofanco HDbaseT-HDR Bedienungsanleitung
gofanco
gofanco HDwireless100-LT Bedienungsanleitung
gofanco
gofanco HDMIExtSplit Bedienungsanleitung
gofanco
gofanco KVMHDExt Bedienungsanleitung
gofanco
gofanco HDBaseT-HD20 Bedienungsanleitung
gofanco
gofanco HDbitT8P Bedienungsanleitung
gofanco
gofanco HDwireless100 Bedienungsanleitung
gofanco
gofanco HDMIExt2 Bedienungsanleitung
gofanco
gofanco G4-0014A Bedienungsanleitung
gofanco
gofanco USBCVXP2VID Bedienungsanleitung
gofanco
gofanco HD20Ext4P-LT Bedienungsanleitung
gofanco
gofanco CAT5E Bedienungsanleitung
gofanco
gofanco HDwireless10x1 Bedienungsanleitung
gofanco
gofanco HDwirelessMini Bedienungsanleitung
gofanco
gofanco HDMIExt4P Bedienungsanleitung
gofanco
gofanco HDbitT4P Bedienungsanleitung
gofanco
gofanco HDBITT4K22 Bedienungsanleitung
gofanco
gofanco prophecy PRO-HDRextract Bedienungsanleitung
