Gossen MetraWatt DIGISKY Bedienungsanleitung

Quickstart Guide

DIGISKY 15448

Exposure Meter for Flash and Ambient Light 1.18/10.19

Essentials

Preparations required for use of the exposure meter

and its basic functions are described in these instructions.

Please check that the exposure meter and accessories

as detailed below are included in the box. If the contents

are incomplete, please contact your local dealer.

▪DIGISKY exposure meter

▪V070A rechargeable battery

▪Power supply and USB connector cable

▪Carrying strap

▪Quickstart guide

The latest version of the detailed operating instructions

can be found and downloaded from the product page at

www.gossen-photo.de . Please download these and read

them carefully.

The DIGISKY is always delivered with the latest firmware.

Should a newer version be available, you can download

it together with the SkyRefresh update program and a

detailed update instructions from the product page.

Afterwards you can do the update of the meter yourself.

Contents

Page

Preparation

Meter Overview

Navigation

Turn On,

Measuring Modes,

Function Selection

Ambient Light

Flash Light

Movie

FCC & IC (USA)

Safety Precautions

Disposal Note

2 GOSSEN Foto- und Lichtmesstechnik GmbH

3. Insert Battery

How to insert and charge the battery

The DIGISKY works with a device-specific, rechargeable lithium-

ion battery. Use the V070A rechargeable battery and the USB

battery charger included with the exposure meter.

Switch your DIGISKY off or wait until the exposure meter is

switched off automatically. Unscrew the battery cover at the back

of the meter with a (Philips) recessed head screwdriver, and then

pull it down and out of the housing.

Insert the battery into the compartment as shown in the figure.

Make sure that the battery is inserted with correct polarity

(+ and –)! Then place the battery cover over the battery

compartment and secure it with the screw.

Connect the cable to the USB port at the exposure meter first,

and then insert the mains plug into an electrical outlet.

The battery can also be charged using a USB port at a PC.

Remove the mains plug to this end, and connect the USB plug to

your PC.

The charging indicator lights up red while the battery is charging.

After the battery has been fully charged, the indicator will light up

green.

To protect the battery pack and prolong its life, do not charge it

for longer than 24 hours without break.

1. Unscrew

2. Remove Cover

Preparation

GOSSEN Foto- und Lichtmesstechnik GmbH 3

Switch device off

Incident light,

flat diffuser

Diffuser ring for incident light /

reflected light measurement,

off

LED`s for meter status

Display panel

Data key

Ring controller

Socket for connecting

flash synchronizing cable

Carrying strap

holder

USB port for charging battery

or data transmission

Meter cell for

reflected light

measurement

Menu key

Measurement key

User

Cam 1

Cam 2

Cam 3

Movie

Retractable

diffuser head

for spherical/

flat /reflected

measurement

ISO

speed

Measuring

function

Measured

values

Analog scale

Exposure

value EV

Cor.

Battery

Incident light

Spherical diffuser

Reflected light

Meter Overview

4 GOSSEN Foto- und Lichtmesstechnik GmbH

Navigation

Main Menu

Press and hold menu key

to select a menu

Use the ring controller

to select a user

to select a setting

Use the ring controller

to select a submenu

Press the measurement key

to confirm

to select a value

Use the measurement key

to exit the menu

GOSSEN Foto- und Lichtmesstechnik GmbH 5

Function Selection: Ambient Light / Flash Light

Use the menu key

to select a function

Measuring Modes

Spherical incident light

measurement

. Reflected light

measurement

Flat incident light

measurement

Off

DIGISKY off

RF Function Selection: All / Group

Radio

Use DATA key and ring

controller

to select all

or groups

Turn On

after

Standby (display OFF)

Activate by pressing any key or turning the instrument head

Automatic switching OFF

Activate with menu key only

Manual switching OFF

Turn instrument head to measurement modes

6 GOSSEN Foto- und Lichtmesstechnik GmbH

Ambient Light

Use the ring controller

to set time / f-stop

Use the ring

controller

to select the desired

value

Press the measurement key to make a measurement.

Contrast measurement: press and hold the measurement key.

Contrast measurement: use the data key to display the average, minimum and maximum value.

GOSSEN Foto- und Lichtmesstechnik GmbH 7

Flash Light

Use the ring

controller

to select the desired

synchronization

speed.

Radio

Use DATA key and

ring controller

to select flash

groups

All / ST

G1 to G4

(Elinchrom)

A to D (Phottix)

LP 1 to LP40

(Broncolor)

Press the measurement key

to perform a measurement.

NonCord

Approx. 45 seconds measurement standby duty -

trigger flash manually

Cord

Synchronizing cable –flash is triggered

RF module –flash is triggered

A compilation of compatible radio systems can be downloaded

from the product page at www.gossen-photo.de .

8 GOSSEN Foto- und Lichtmesstechnik GmbH

Movie

Settings f-stop, sector angle, sensitivity etc. are set in the main menu.

EV analog display

Illuminance,

luminance

Measured value

with correction

Shutter

angle

CINE

speed

Press the measurement key to perform a measurement.

For continuous measurement: press and hold the measurement key;

use data key to display the average, minimum and maximum value.

Use the menu key

to switch the

display from

f-stop value to

photometric

value.

Movie

GOSSEN Foto- und Lichtmesstechnik GmbH 9

The following data, required for the fulfillment of FCC and IC regulations, are referred to the meter mentioned in this document.

Product name: DIGISKY

Model number: H260A

FCC ID number: YXF-DIGISKY

IC number: 9333A-DIGISKY

Company name: GOSSEN Foto- und Lichtmesstechnik GmbH

FCC & IC - USA

Modifications

Any changes or modifications not expressly approved by the manufacturer could void the user's authority to

operate the equipment.

Conditions of

Operations

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

15.105

Class B digital device

or peripheral

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

15.105

Class A digital device

or peripheral

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense.

10 GOSSEN Foto- und Lichtmesstechnik GmbH

Safety Precautions

In the event of malfunctioning, switch the light meter off immediately.

If the event that smoke develops or unusual odors become apparent, which are caused by either the measuring instrument or the power

supply, disconnect from mains power immediately and remove the rechargeable battery from the instrument in order to prevent possible

fire. Continuing to operate the measuring instrument or the power supply after such malfunctions have occurred may result in severe

injury. Please contact your local dealer or GOSSEN Service in order to eliminate malfunctioning. If you bring or send the instrument in for

repairs, make sure that the rechargeable battery has been removed first.

Never use the measuring instrument in proximity to flammable gases.

Electronic devices must not be used near flammable gases. Otherwise there would be danger of explosion and fire.

Never hang the meter and/or the carrying strap around the head or neck of a child.

Danger of strangulation exists if the carrying strap is hung around the head or neck of a child.

Store the measuring instrument at a location which cannot be accessed by children.

The measuring instrument and its accessories include parts which can be swallowed. Make sure that these parts (e.g. housing covers,

rechargeable batteries etc.) do not fall into the hands of children who might swallow them. Otherwise, danger of suffocation prevails.

Use suitable cables only.

Use only the included, original GOSSEN cables for connection to external devices. GOSSEN assumes no liability if other cables are

used.

Do not dismantle the exposure meter.

Never touch any parts located inside of the housing –injury may result. Never attempt to repair the meter yourself or try to open the

meter. Repairs may only be made by qualified personnel. If the meter’s housing is damaged due to dropping or other external influences,

remove the rechargeable battery or power supply and contact your local dealer or GOSSEN Service for repair.

Avoid any and all contact with the liquid crystals.

If the display is damaged (e.g. broken), danger of injury due to contact with glass shards or discharge of liquid crystals exists. Make sure

that skin, eyes and mouth do not come into contact with the liquid crystals.

Andere Handbücher für DIGISKY

Inhaltsverzeichnis

Andere Gossen MetraWatt Messgerät Handbücher

Gossen MetraWatt

Gossen MetraWatt MAVO-MONITOR Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt E-Clip 1 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MID U1281 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt PROFITEST MBASE MTECH Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt COIL ADAPTER XTRA Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRACLIP 88 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt PhaseCop2 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVOWATT 4 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAOHM 413 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRACLIP 41 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVO-SPOT Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAFLEX 300M Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt SECULIFE IM Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt lunasix Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRISO G1000 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt U1281 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVOPAD Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt LonWorks U128-W1 Series Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt mavolog pro Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt SECULIFE ITBASE Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRACLIP 41 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt Starlite 2 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAwin 10 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVO-MONITOR Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung