Gossen MetraWatt MID U1281 Bedienungsanleitung

Operating Instructions

3-349-618-15

3/12.18

MAIN PISTRIBUTION – PRODUCTION

ENERGYMETER|MID

Electronic Active Energy Meters

U1281/U1289/U1381/U1387/U1389

GMC-I Messtechnik GmbH

Südwestpark 15

90449 Nürnberg • Germany

Phone +49 911 8602-111

Fax +49 911 8602-777

E-Mail info@gossenmetrawatt.com

www.gossenmetrawatt.com

Edited in Germany • Subject to change without notice • A pdf version is available on the Internet

2 GMC-I Messtechnik GmbH

1 Safety Precautions – Symbols

– Check the specified nominal voltage on the serial plate

before placing the instrument into service.

– Observe the maximum voltage of the pulse output.

– Make sure the connector cables are not damaged, and

that they are voltage-free while wiring the instrument.

– If it can be assumed that safe operation is no longer pos-

sible, the instrument must be immediately removed from

service (disconnect input voltage!). Safe operation can no

longer be relied upon if the instrument demonstrates visi-

ble damage.

The device may not be placed back into operation until

troubleshooting and repair have been performed, and

calibration and dielectric strength have been tested and

approved at our factory or an authorized service center.

– Voltage conducting parts may be exposed if the cover is

opened.

If balancing, maintenance or repair of a live open instru-

ment is required, work may only be carried out by trained

personnel who are familiar with the dangers involved.

Capacitors inside the instrument may be dangerously

charged, even after it has been disconnected from all

power sources.

– After the instrument has once again been closed subse-

quent to repair or maintenance work, insulation must be

tested with high-voltage in accordance with the values

specified in the technical data.

GMC-I Messtechnik GmbH 3

Meaning of Symbols on the Instrument

DE MTP 11 B 001 MI-003 Prototype test certificate

Total insulation,

Safety Class II device

Warning concerning a source of danger

(Attention, observe documentation!)

This device may not be disposed of with the trash. Fur-

ther information regarding the WEEE mark can be

accessed on the Internet at www.gossenmetrawatt.com

by entering the search term ’WEEE’.

Metrology label with year (M11) and registration

number of the indicated authoring for module D.

Duration of Calibration validity country specific

Label with seal from federally

approved test authority

(for recalibration only)

Tamper-proof sealing

The manufacturer‘s lead seal for calibration protection is

located at the back of the instrument.

Tamper-proof sealing for the terminal cover can be attached

either at the left or right-hand side of the terminal cover.

M111948

4 GMC-I Messtechnik GmbH

2 Serial Plate – Terminals

Type designation

UNfN

LED constant

Year of manufacture

Accuracy class

CT: Current transformer transformation ratio

VT: Voltage transformer transformation ratio

Serial number

Pulse outpput

IMIN-IN(IMAX)

External auxiliary

Reverse Action Lock

The values of CT, VT and Son the serial plate can be / are calibrated

Operating

Bus connection

temperature range

voltage

Circuit Symbols

4-L

3-L

2-L

U12/U1389:

U1387:

U12/U1381:

GMC-I Messtechnik GmbH 5

Voltage Voltage Voltage

Current Current Current

L3L2L1 N

CurrentCurrentCurrent

Inputs

2.5 mm2 with wire end ferrules or

16 mm2 without wire end ferrule



2 x 1.5 mm2 without wire end ferrule

Voltage:

Current:



2.5 mm

with wire end furrule or





2 x 1.5 mm

without wire end ferrule

Auxiliary voltage

BUS

Enable key

24 V



10%

(Feature H1)

Pulse

output

12 3 4 5 6 78 9112021222324

+–

Tighten screws by hand only! Tightening torque

Note:

Observe the wiring diagram in the terminal cover

Attention:

!for current terminals (No. 1, 3, 4, 6, 7 and 9) = 2 Nm

for all other terminals (No. 2, 5, 8, 11, 20 to 24) = 0.4 Nm

6 GMC-I Messtechnik GmbH

3 Pulse Output – Bus Interfaces

underligned values are default values in as-delivered condition

The interface descriptions for the active energy meters are

available on the Internet under www.gossenmetrawatt.com.

Pulse rates fix V1/V3

V8 fix V9 Programmable V2/V4

Direct

U1281 / U1289

1000puls./kWh

100 — — 1 1000

pulses/kWh

Transformer

U1381 / U1387 / U1389

f (secondary)

CT = VT = 1 (Q0) 1000

puls./kWh

100

1000

100



10000



1000



10000puls./kWh

CT, VT progr. (Q1) 1000

puls./kWh

100

1000



1000



10000

puls./kWh

CTxVT; CT, VT fix (Q9)

f (primary) f (primary)

1 10

1000puls./kWh

—11000 pulses/kWh

11 100

100 pulses/kWh

—0,1100 pulses/kWh

101 1000

10 pulses/kWh

—0,0110 pulses/kWh

1001 10000

1 pulses/kWh

—11000 pulses/MWh

10001



100000

0,1 pulses/kWh

—0,1100 pulses/MWh

100001



1000000

0,01 puls./kWh

— 0,01 10 pulses/MWh

External Voltage Source

Energy Import

max. 40 V

AC/DC

Energy Import

max. 375 V

24 V DC

I = max. 100 mA

I = max. 27 mA

External Voltage Source

Standard pulse duration: 30 ms + 5%, Interpulse period: > 30 ms

Pulse duration V7/V8: 130 ms + 5%, Interpulse period: > 130 ms

GMC-I Messtechnik GmbH 7

4 Display and Control Panel

4.1 Test LED

The test LED is located between the LCD and the serial

plate. The higher the measured power value, the higher the

blink rate. If all currents are lower than the starting current,

the LED lights up permanently.

LED Constant

U128x: 10 000 pulses/kWh

U138x: 100 000 pulses/kWh

4.2 Resolution of Energy Import Main Display (Large Characters)

For calibratable main displays (Q0 or Q9), the calibration reading

indicates an additional digit after the decimal point. Therefore,

the leading digit is omitted in the case of 7-digit presentation.

Meter

Feature

CTxVT

min.

CTxVT

max.

Standard

Reading

Calibration

Reading *

Unit

U1281, U1289 — — 123456.7 23456.78 kWh

U138x

Q0 or Q9 1 10 12345.67 2345.678 kWh

11 100 123456.7 23456.78 kWh

101 1000 1234567 234567.8 kWh

1001 10000 12345.67 2345.678 MWh

10001 100000 123456.7 23456.78 MWh

100001 1000000 1234567 234567.8 MWh

1 10 123456.7 kWh

11 100 1234567 kWh

101 1000 12345.67 MWh

1001 10000 123456.7 MWh

10001 100000 1234567 MWh

8 GMC-I Messtechnik GmbH

4.3 Meanings of Symbols on the LCD

Main display

is not/cannot be calibrated,

is displayed.

Correct connection:

Continously lit phase symbols

Phase failure:

Symbol for affected phase is cleared from display.

Incorrect phase sequence:

Phase symbols blink in the following order: 3-2-1.

Negative power:

Respective phase symbol blinks.

4 quadrant display of instantaneous power: posi-

tive or negative active power P, positive or nega-

tive reactive power Q.

For bus connection: appears when the

meter transmits a data packet.

Main display (active energy Etot* in kWh or MWh)

Auxiliary display (instantaneous power Pmom*)

Error: alternating error code and instantaneous power

* U138x: CT and VT are taken into consideration

GMC-I Messtechnik GmbH 9

Key Symbols for Parameters Configuration

Key and 2nd key bit blanked:

Parameters CT, VT or S0 configurable according to fea-

tures, can be disabled with enable key.

Key displayed with one key bit:

Parameters CT, VT or S0 disabled,

can be changed after activating enable key.

Key blanked, 2nd key bit displayed:

Parameters CT, VT or S0 (which are / can be calibrated)

are preset at the factory, can be queried in the display

mode, other values can be set.

Key with 2nd key bit displayed: parameters (which can be /

are calibrated) are preset at the factory, other values are

disabled with enable key and can be reset after cancel-

ling the disable function.

Values which are preset at the factory are specified addi-

tionally on the serial plate in as-delivered condition.

Symbols Adjustable

parameters

Disabled

parameters

Fixed/

calibrated

parameters

Feature

CT, VT Q1

S0 V2, V4

CT, VT Q1

S0 V2, V4

CT, VT S0

Q1 and V1/V3/V7/V8/V9

S0 CT, VT V2/V4 and Q0/Q9

CT, VT S0

Q1 and V1/V3/V7/V8/V9

S0 CT, VT V2/V4 and Q0/Q9

S0, CT, VT V1/V3 and Q0/Q9

S0, CT, VT V7/V8/V9 and Q0

10 GMC-I Messtechnik GmbH

4.4 Key Operation

Querying parameter values CT, VT and S0

Apart from the LCD test, the menu key located between

LCD and serial plate serves to query current paramter val-

ues and, in the case of active energy meters with special

features, to change parameters (provided that the enable

key has been activated before). The sequence can be seen

from the figure on the right.

If no key is pressed for 2 minutes, the display returns auto-

matically to the standard setting.

Parameters can be changed in the following instruments:

Parameters CT, VT for U138x with feature Q1,

parameters S0 for U128x/U138x with feature V2/V4

a) Enabling parameter modifications

The enable key serves to enable or disable paramter

changes. It is located below the terminal cover and is acti-

vated with a pointed object (e. g. ballpen).

Pressing the key for the first time activates operating mode

„Change parameters“ (key off):

Renewed activation disables operating mode „Change

parameters“ (key on):

If the key is not activated for approx. 2 minutes, operating

mode „Change parameters“ is automatically aborted and

blocked.

The key is displayed again:



Dieses Handbuch passt für folgende Modelle

Andere Gossen MetraWatt Messgerät Handbücher

Gossen MetraWatt

Gossen MetraWatt METRAwin 10 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVOLUX 5032C USB Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRA HIT 22S Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRACLIP 85 Leitfaden

Gossen MetraWatt

Gossen MetraWatt PROFITEST PV 1500 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt PROFITEST MBASE MTECH Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt PROFITEST MF Series Betriebsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVO-SPOT 2 USB Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt Z227O Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVO-SPOT Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVOWATT 230 Betriebsanleitung

Gossen MetraWatt

Gossen MetraWatt DIGISIX 2 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRACLIP 41 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt LonWorks ENERGYMID U228 W1 Series Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAFLEX 300M Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt SECULIFE IM Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRACABLE TDR PRO Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt SINEAX DME 400-1 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt Luna-star F Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt DIGISKY Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRISO PRO Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt DIGISKY Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt PhaseCop2 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt mavolog pro Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung