Graco G3-G-12NC-2L0000-00C00000 Bedienungsanleitung

332291G

Instructions

G3 Standard Automatic

Lubrication Pump

For dispensing of NLGI Grades #000 to #2 greases and oil with at least 40cSt. For

Professional Use Only.

Not approved for use in explosive atmospheres or hazardous locations.

Part Nos., page 3

5100 psi (35.1 MPa, 351.6 bar) Pump Output Pressure

5000 psi (34.4 MPA, 344.7 bar) Fill Inlet Pressure

Important Safety Instructions

Read all warnings and instructions in this

manual. Save these instructions.

Conforms to ANSI/UL 73

Certified to CAN/CSA

Std. 22.2 No 68-09

3132066

2332291G

Contents

Part / Model Numbers . . . . . . . . . . . . . . . . . . . . . . . 3

2 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

8 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

12 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . 3

16 Liter Models . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Understanding the Model Number . . . . . . . . . . . 4

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . 8

Typical Installation - With Remote Fill Manifold . . 9

Optional Installation -

Without Remote Fill Manifold . . . . . . . . . . . 10

Choosing an Installation Location . . . . . . . . . . . 11

System Configuration and Wiring . . . . . . . . . . . 12

Wiring and Installation Diagrams . . . . . . . . . . . 13

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting to Auxiliary Fittings . . . . . . . . . . . . . 18

Setting Pump Outlet Volume . . . . . . . . . . . . . . . 19

Loading Grease . . . . . . . . . . . . . . . . . . . . . . . . 19

Auto-Fill Shut Off . . . . . . . . . . . . . . . . . . . . . . . . 21

Filling Oil Unit . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Pump Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Parts - 2 Liter Models . . . . . . . . . . . . . . . . . . . . . . 29

Parts - 4 Liter and Larger Models . . . . . . . . . . . . . 30

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Mounting Pattern . . . . . . . . . . . . . . . . . . . . . . . . 35

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 36

Graco Information . . . . . . . . . . . . . . . . . . . . . . . 36

Part / Model Numbers

332291G 3

Part / Model Numbers

The Part Number is a six-digit unique number that is only used to order the G3 Pump. Directly related to this six digit

Part Number is the configured Graco Model Number. This configured number identifies the distinct features of a spe-

cific G3 Pump. To help you understand each component that makes up the Model Number see Understanding Your

Model Number, page 4. The tables below shows the relationship between each Part Number and its related Model

Number.

2 Liter Models

4 Liter Models

8 Liter Models

12 Liter Models

16 Liter Models

Part

Numbers Model Number

96G000 G3-G-12NC-2L0000-00C00000

96G001 G3-G-24NC-2L0000-00C00000

96G002 G3-G-ACNC-2L0000-0D000000

96G003 G3-G-12NC-2L0A00-L0C00000

96G005 G3-G-24NC-2L0A00-L0C00000

96G006 G3-G-24NC-2LFA00-L0C00000

96G007 G3-G-ACNC-2L0A00-LD000000

96G008 G3-G-ACNC-2LFA00-LD00000

96G050 G3-A-24NC-2L0A00-L0C00000

96G059 G3-A-ACNC-2L0A00-LD000000

96G182 G3-G-24NC-2L0A00-0D00L000

Part

Numbers Model Number

96G038 G3-G-12NC-4L0L00-00C00000

96G040 G3-G-24NC-4L0000-00C00000

96G042 G3-G-ACNC-4L0000-0D000000

96G044 G3-G-12NC-4L0A00-L0C00000

96G048 G3-G-24NC-4L0A00-L0C00000

96G051 G3-A-24NC-4L0A00-L0C00000

96G053 G3-G-24NC-4LFA00-L0C00000

96G055 G3-G-ACNC-4L0A00-LD000000

96G060 G3-A-ACNC-4L0A00-LD000000

96G062 G3-G-ACNC-4LFA00-LD000000

96G173 G3-G-ACNC-4LFA00-0D00L000

96G179 G3-G-ACNC-4LFA00-0D00L000

96G184 G3-G-24NC-4L0A00-0D00L000

96G210 G3-G-24NC-4LAA00-0D00L000

96G180 G3-G-24NC-4L0A02-L0C00000

96G202 G3-G-ACNC-4L0A00-0D00L000

96G204 G3-G-24NC-4LFA00-0D00L000

Part

Numbers Model Number

96G039 G3-G-12NC-8L0000-00C00000

96G041 G3-G-24NC-8L0000-00C00000

96G043 G3-G-ACNC-8L0000-0D000000

96G045 G3-G-12NC-8L0A00-L0C00000

96G049 G3-G-24NC-8L0A00-L0C00000

96G052 G3-A-24NC-8L0A00-L0C00000

96G056 G3-G-ACNC-8L0A00-LD000000

96G061 G3-A-ACNC-8L0A00-LD000000

96G187 G3-G-ACNC-8LFA00-0D00L000

96G189 G3-G-24NC-8L0A00-0D00L000

96G192 G3-G-24NC-8LFA00-L0C00000

96G198 G3-G-24NC-8L0A06-0C000000

96G207 G3-G-ACNC-8LAA00-LD000000

96G213 G3-G-24NC-8LAA00-0D00L000

96G217 G3-G-24NC-8LAA06-00C00000

96G205 G3-G-24NC-8LFA00-0D00L000

Part

Numbers Model Number

96G057 G3-G-ACNC-120A00-LD000000

96G171 G3-G-24NC-120000-00C00000

96G199 G3-G-24NC-120A00-L0C00000

Part

Numbers Model Number

96G058 G3-G-ACNC-160A00-LD000000

96G172 G3-G-24NC-160000-00C00000

96G220 G3-G-24NC-1600A00-L0C00000

Part / Model Numbers

4332291G

Understanding the Model Number

Use the Code Sample provided below to identify each component’s location in the Model Number. The options for

each component that make up the code are provided on the lists below.

NOTE: Other pump configurations are available that are not documented in this manual. Contact Graco Customer

Service or your local Graco distributor for assistance.

G3 - G = Identifies pump as being a G3; G = Grease

G3 - A = Identifies pump as being a G3; A = Oil

Code aa: Power Source

• 12 = 12 Volts DC

• 24 = 24 Volts DC

• AC = 100 - 240 Volts AC

Code bb: Operation Control

• NC = No Controller

Code cc: Reservoir Capacity (Liters)

• 2L = 2 Liters

• 4L = 4 Liters

• 8L = 8 Liters

• 12 = 12 Liters

• 16 = 16 Liters

Code d: Follower Plate Installed

• F = Follower Plate Installed

• 0 = No Follower Plate

• A = Auto-Fill Shut Off

Code e: Low Level Option

• A = External Low Level

• 0 = No Low Level monitoring

Code ff: Options

• 00 = No Options

• 06 = Low Level in CPC

Code g, h, i, j, k, m, n, p

NOTE: Codes g - p relate to a specific location on the

G3 pump. See FIG. 1 for these locations.

•C=CPC

•D=DIN

• L = Low Level

• 0 = Not populated

G3 - G - NC 0 0 0 0 0 0

Code Sample: a a b b - c c d e f f - g h i j k m n p

FIG. 1

Warnings

332291G 5

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When

these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific

hazard symbols and warnings not covered in this section may appear throughout the body of this manual where

applicable.

WARNING

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause

electric shock.

• Turn off and disconnect power at main switch before disconnecting any cables and before servicing

or installing equipment.

• Connect only to grounded power source.

• All electrical wiring must be done by a qualified electrician and comply with all local codes and reg-

ulations.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information

about your material, request MSDS from distributor or retailer.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine man-

ufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and cre-

ate safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

Warnings

6332291G

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This

may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgi-

cal treatment.

• Do not point dispensing device at anyone or at any part of the body.

• Do not put your hand over the fluid outlet.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking,

or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

PRESSURIZED EQUIPMENT HAZARD

Over-pressurization can result in equipment rupture and serious injury.

• A pressure relief valve is required at each pump outlet.

• Follow Pressure Relief Procedure in this manual before servicing.

PLASTIC PARTS CLEANING SOLVENT HAZARD

Many solvents can degrade plastic parts and cause them to fail, which could cause serious injury or

property damage.

• Use only compatible water-based solvents to clean plastic structural or pressure-containing parts.

• See Technical Data in this and all other equipment instruction manuals. Read fluid and solvent

manufacturer’s MSDSs and recommendations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equip-

ment, follow the Pressure Relief Procedure and disconnect all power sources.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, includ-

ing eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes

but is not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufac-

turer

WARNING

Installation

332291G 7

Installation

Component Identification

Key:

AReservoir

B Adjustable Pump Element (1 included. Can accommodate 3

total)

C Pressure Relief Valve (Not included (not shown) / required for

each outlet - Available from Graco. See Parts, page 32.)

D Zerk Inlet Fill Fitting (1 included / grease models only)

E Pump Outlet Plug (2 included)

F Volume Control Spacers (2 included. More spacers = less

output volume per stroke) (also see FIG. 18, page 19)

G Fuse (DC models only - Not included, not shown. Available

from Graco. See Parts, page 32.)

H Power / Sensor Panel (both sides; only one side shown)

I Part Number / Model Number example only shown, (see

page 4, Understanding the Model Number, for details)

J Power Cord (DIN shown)

K Follower Plate (grease models only / not available on all

grease models)

L Vent Hole for Follower Plate (grease models only / not

available on all grease models)

M Fill cap (oil models only)

N Auto-Fill Shut Off

FIG. 2

G3-G-24NC-2L0A00-L0C00000

Grease Models with Follower

Plate

96GXXX

Oil Models

Grease Models

Auto-Fill Shut Off Models

Installation

8332291G

Typical Installation

Series Progressive Divider Valve

Injector Installations

Key

A Connected to fused power source

B Pressure relief valve (Not included/ required for each out-

let - user supplied. See Parts, page 32)

C Supply Hose (user supplied)

D Series progressive divider valves (Divider Installations)

- Injectors (Injector Installations)

E To lube points

F - Proximity Switch (Divider Installations)

- Pressure switch (Injector Installations)

G Vent valve (Not included / available from Graco. See

Parts, page 33.)

H Return to reservoir

FIG. 3

FIG. 4

Installation

332291G 9

Typical Installation - With Remote Fill Manifold

The installation shown is only a guide for selecting and installing system components. Contact your Graco distributor

for assistance in planning a system to suit your needs.

Key:

AG3Pump

B Auto-Fill Shut Off Valve

C Auto-Fill Inlet

D G3 Reservoir

E Remote Fill Reservoir

F Remote Fill Pump

G Supply Hose (user supplied)

H Air Supply to Refill Pump

J Supply Hose (user supplied)

K Pressure Relief Valve

L Drain Hose

M Fill Coupler/Inlet (quick disconnect)

N Fill Manifold

P Fill Manifold Outlet

Q Fill Manifold Vent Port

R Pressure Gauge

S Pressure Regulator and Gauge

T Pressure Relief Knob

To relieve the stall pressure in the fill line a fill manifold

(N) must be installed in the system.

FIG. 5

Installation

10 332291G

Optional Installation - Without Remote Fill Manifold

The installation shown is only a guide for selecting and installing system components. Contact your Graco distributor

for assistance in planning a system to suit your needs.

NOTE: The remote filling station pump stalls (dead-heads) when the reservoir is full. If the pump does not stall

(dead-head) there is a leak in the system.

Key:

AG3Pump

B Auto-Fill Shut Off Valve

C Auto-Fill Inlet

D G3 Reservoir

E Remote Fill Reservoir

F Remote Fill Pump

HReliefValve

J Supply Hose (user supplied)

LDrainTube

L1 Option - To reservoir

L2 Option - To overflow container

S Pressure Regulator and Gauge

U Pressure Relief Valve

V Quick Disconnect

W Overflow Container

Y Supply Hose Pressure Relief Valve

To relieve the stall pressure in the fill line a ball valve

(Y) must be installed in the system.

FIG. 6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco Husky 2200 Gebrauchs- und Pflegehandbuch

Graco

Graco Series A Bedienungsanleitung

Graco

Graco 970056 Bedienungsanleitung

Graco

Graco ProMix PD2K Bedienungsanleitung

Graco

Graco H Series Bedienungsanleitung

Graco

Graco G3-G-24NC-8LTA00-0D00L000 Bedienungsanleitung

Graco

Graco Husky 515 series Bedienungsanleitung

Graco

Graco Z-Pump Elite Series Bedienungsanleitung

Graco

Graco 206405 Datenblatt

Graco

Graco Husky 1050HP Bedienungsanleitung

Graco

Graco 257100 Bedienungsanleitung

Graco

Graco Husky 1050 Series Bedienungsanleitung

Graco

Graco T2 Bedienungsanleitung

Graco

Graco ToughTek MP-Series Bedienungsanleitung

Graco

Graco Husky 2150e Gebrauchs- und Pflegehandbuch

Graco

Graco Husky 1050HP Bedienungsanleitung

Graco

Graco Twistork Helix 308345T Stücklistenhandbuch

Graco

Graco Therm-O-Flow C03508 Stücklistenhandbuch

Graco

Graco President B Series Datenblatt

Graco

Graco 222-831 Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

Graco

Graco 1590 SA Bedienungsanleitung

Graco

Graco Husky 2150e Bedienungsanleitung

Graco

Graco MSA-10 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung

GÜDE

GÜDE HWW 900 GC Bedienungsanleitung