GRAPHTEC FC7000 Series Handbuch

GRAPHTEC FC7000

CONTROL PANEL SETUP

IMPORTANT-If you are going to reset to factory defaults, make sure the operator has a list of CONDITIONS

settings [force, speed] written down for the different conditions they have been using so they can re-enter the

values. Also record Sensor Offset Values if they have previously been established.

RESET TO FACTORY DEFAULTS:

FC7000Mk2 and FC7000 series:

1. Power off the cutter

2. Press and hold UP arrow key while power back on

3. Release Up key when shown "NOVRAM Clear Start"

4. Press F3 "HP-GL (w/inch)"

** choose other may cause display non-English menu

5. Press DOWN arrow to switch to YES

6. Press ENTER key to confirm

FC7000 CONTROL PANEL SETTINGS:

The following instructions explain how to properly set your plotter up when using Graphtec Type 2

Half-Inch Registration Marks in a Print and Cut Workflow. If setting is not specified leave it at the default.

Set Distance Adjust

1. Axis R.M.S.

2. F1 (Auto Reg Mark)

3. F4 (Distance Adjust)

4. F2 (OFF)

5. Enter

Set Mark Type

1. Axis R.M.S.

2. F1 (Auto Reg Mark)

3. F2 (Mark Type)

4. Select the Type of mark, Type 1 or 2* (Type 2 is generally used)

5. Enter

6. F3 (Other Setups)

7. F1 (Mark Size)

8. Change with Down Arrow to 0.52 inches (13mm)

9. Enter

Set Mark Scan Mode

1. Axis R.M.S.

2. F1 (Auto Reg Mark)

3. F1 (Mark Scan Mode)

4. F3 (Enable)

5. Enter

6. F4- 4 POINTS*

7. Enter

8. Mark Position (All zeros)

F1 > 1

F2 > 2

F3 > 3

Note: The Scan Mark setting allows you to specify areas that the plotter will not sense by specifying the

distance between the registration marks. Once the plotter locates the first registration mark, it will

automatically move the specified distance and begin scanning for the next mark. You can also use this

function to reduce mark-sensing time, though before you begin, you must know the distance between

registration marks. If you wish to have the plotter scan the full length and width of the media, simply set

the X and Y values to 0. This will increase the time it takes to scan for the registration marks, but does

not require you to know the exact length and width of your cut job. Consult the plotter's documentation

for further information on this feature.

9. Next (to accept the current setting) or Enter (to adjust the Scan Mark setting)

Set For Manual control

1. Menu Button

2. Next

3. Next

4. Next

5. F2 (Background Setting)

6. Next

7. Next

8. F3 Manual

9. Enter

10. Menu

Set Command Mode

1. Menu Button

2. Next

3. Next

4. F1 (Interface)

5. F4 (Command)

6. F4 (HP-GL) for Photoprint, Flexi or Wasatch----(GPGL for Cutting Master)

7. Enter

8. Menu

RESET THE CONDITIONS AND TOOL PROPERTIES.

CONTROL PANEL

(Reminder: While moving the carriage with the POSITION keys, hit the NEXT button for Fast speed)

To change the setting of a CONDITION, such as the Force:

•Press the “F” button to switch to the condition you want to modify, for example press the F1

button once to modify CONDITION 1, press it again to toggle to CONDITION 5; press F2 for

CONDITION 2 and 6, and so on.

•Press the CONDITIONS button.

•The cursor blinks next to the Force setting (If you want to change another value press the button

corresponding to that value, example F2 to move the cursor to the SPEED variable).

•Toggle the value up or down with the directional keys. Press the ENTER button to save the value.

SENSOR OFFSET ADJUST

Per Graphtec we need to begin using “Sensor Offset Adjust” rather than “Axis Origin Offset.” Both methods

result in shifting the cut lines but, the Sensor Offset Adjust will NOT move the ORIGIN point.

REMEMBER: Increase the X and Y values shift the cut lines to the upper left if you are standing in front

of the cutter.

Y = (right to left, positive values shift left), X = (down to up, positive values shift cut lines up)

1.) Ensure the customer has “Ready” displayed on the screen.

Hit F1 to be sure you are editing the correct condition

2.) Hit the “AXIS/RMS Key”

3.) Hit “F1” for Auto Reg Mark

4.) Hit “F3” for Other Setups

5.) Hit “F2” Sensor Offset Adjust

6.) Hit “F3” for Method 1

7.) Hit “F3” for Parameter Set

8.) Arrow up or down to change X and Y Axis. Hit “Enter” to confirm.

Andere Handbücher für FC7000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GRAPHTEC Plotter Handbücher

GRAPHTEC

GRAPHTEC CUTTING PRO FC2250 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC8600 SERIES Bedienungsanleitung

GRAPHTEC

GRAPHTEC MP303-04 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC7000 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE6000-120AP Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC4200-50 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FCX4000 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC FC7000-75 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE5000-60 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE5000-120AP Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE7000-130AP Bedienungsanleitung

GRAPHTEC

GRAPHTEC Craft ROBO CC100 Benutzerhandbuch

GRAPHTEC

GRAPHTEC FCX4000 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC CC300-20 Craft ROBO Bedienungsanleitung

GRAPHTEC

GRAPHTEC Craft ROBO CC100 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE6000 SERIES Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE7000-130AP Benutzerhandbuch

GRAPHTEC

GRAPHTEC Craft ROBO CC100-20 Programmierhandbuch

GRAPHTEC

GRAPHTEC CE LITE-50 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE2000-60 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC8000 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE6000-120AP Benutzerhandbuch

GRAPHTEC

GRAPHTEC CE6000 SERIES Bedienungs- und Sicherheitshinweise

GRAPHTEC

GRAPHTEC FCX2000 SERIES Benutzerhandbuch

Beliebte Plotter Handbücher anderer Marken

MUTOH

MUTOH Kona 760 Bedienungsanleitung

HP 7475a Bedienungsanleitung

Vulcan-Hart

Vulcan-Hart FC-500VC Bedienungsanleitung

Roland

Roland TrueVIS VG-640 Betriebsanleitung

Furuno

Furuno RP-180 Bedienungsanleitung

Roland

Roland VersaCamm SP-540V Bedienungsanleitung

MIMAKI

MIMAKI CF2 Series Bedienungsanleitung

Ioline

Ioline Summit Bedienungsanleitung

Summa

Summa S CLASS Bedienungsanleitung

Gerber Technology

Gerber Technology GERBERplotter MP Series Bedienungsanleitung

Furuno

Furuno RP-17 Bedienungsanleitung

HP 7470A Bedienungsanleitung

SII

SII LP-1010 Bedienungsanleitung

Great Computer

Great Computer JII-61 Bedienungsanleitung

Roland

Roland VersaUv LEF - 12i Bedienungsanleitung

Lectra

Lectra Alys 120 Bedienungsanleitung

MUTOH

MUTOH Ultima SC-850D Bedienungsanleitung

Skycut

Skycut D Series Bedienungsanleitung