GRAPHTEC CE6000 SERIES Bedienungs- und Sicherheitshinweise

1/4

New procedure to replace the main board of CE6000

The CE6000 series has a Sub-NVRAM on the cam sensor board.

This Sub-NVRAM is backing up all settings values for the main board.

Therefore all setting values are able to copy from the Sub-NVRAM to the main board without inputting

adjustment values from the factory adjustment label when the main board is replacing.

This function will help you when you are going to replace the main board of CE6000 series.

Note: This function is supported from the rmware version 1.30.

How to copy the adjustment values from the Sub NVRAM to the main board

(1) Turn off the power for the CE6000 if the power was on.

(2) Replace the main board.

(3) Perform the NV-RAM clear with corresponding model of dip-switch settings.

Set the dip-switch settings with corresponding model to the NV-RAM clear mode.

Dip Switch 1234Model

SW1

1234

OFF OFF OFF OFF ON CE6000-40

SW1

1234

OFF ON OFF OFF ON CE6000-60

SW1

1234

OFF OFF ON OFF ON CE6000-120/120AMO

SW1

1234

OFF ON ON OFF ON CE6000-120AP

(4) Turn on the power for the CE6000 after the dip-switches were set to the NV-RAM Clear mode.

(5) Wait until the NV-RAM Clear was nished.

(6) Turn off the power for the CE6000 when the NV-RAM Clear was nished.

(7) Set the dip-switch settings with corresponding model to the normal mode.

Dip Switch 1234Model

SW1

1234

OFF OFF OFF OFF OFF CE6000-40

Old Grid Roller (Right side grid roller width 150 mm)

SW1

1234

OFF OFF OFF ON OFF CE6000-40

New Grid Roller (Right side grid roller width 160 mm)

SW1

1234

OFF ON OFF OFF OFF CE6000-60

SW1

1234

OFF OFF ON OFF OFF CE6000-120/AMO

SW1

1234

OFF ON ON OFF OFF CE6000-120AP

2/4

(8) Turn on the power while pressing the down arrow key and the ENTER key.

The following menu is displayed.

(9) If the above status of SERIAL NUMBER and FACTORY VALUE is OK, the adjustment values are able

to copy from the Sub-NVRAM to the main board.

(10) Press F1 key to copy the value to the main board.

(11) The plotter will be initialized automatically after the values are copy to the main board.

This will nish in a few second.

(12) Turn off the power.

(13) End of replacing the main board.

When the Sub NV-RAM values were not able to copy to the main board

The Sub-NVRAM valuer are not able to copy to the main board when the following menu was displayed.

This menu will be displayed when the previous main board setting values were not copied from the Sub-

NVRAM.

This menu will be displayed when the cam sensor was replaced without backup to the Sub-NVRAM.

All adjustments have to perform when above menus were displayed (Refer to the service manual of CE6000

to adjust all adjustments.).

And all adjustment values must upload to the Sub-NVRAM.

3/4

How to backup the main board value to the Sub-NVRAM

Prepare following items before backup.

1. PC

2. SEND.EXE

3. USB cable

4. The CE6000 series of USB driver must be installed before using the SEND.EXE.

5. Serial number of CE6000 (The serial number is “E” and 9 digits of numbers.)

6. The backup command le. (This le has to create by the text editor such as word pad.)

How to create the backup command le

Type the following character by using the text editor.

a10,1,Exxxxxxxxx,

The "Exxxxxxxxx" is serial number of the CE6000.

For example if the serial number is "E209200001", type as below.

a10,1,E209200001,

Save the le after type it.

Procedure

The back up command should be sent in the READY menu of maintenance mode.

(1) Connect the CE6000 and the PC via the USB.

(2) Load a paper into the CE6000.

(3) Turn on the power while pressing the FAST key and the ENTER key.

The following menu is displayed.

(4) Send the backup command le to the CE6000 by using the SEND.EXE.

Select the backup command le

Select all les

Press the Print button after the

backup command le and the

output device were selected.

Select the CE6000.

Conrm the active device at the

“Device and Printers” before

selecting the output device.

4/4

(5) The READY will be displayed after the backup was nished.

Turn off the power the after backup was nished.

The backup will be nished in about 30 seconds.

(6) Turn on the power while pressing the down arrow key and the ENTER key.

The following menu is displayed.

(7) Conrm that serial number is correct with the backup procedure.

And conrm the SERIAL_NUMBER and FACTORY_VALUE are showing the “OK”.

(8) Turn off the power for the CE6000.

Andere Handbücher für CE6000 SERIES

Andere GRAPHTEC Plotter Handbücher

GRAPHTEC

GRAPHTEC FC5100A-75 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC9000-75 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE3000-120 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC8600-60 Bedienungsanleitung

GRAPHTEC

GRAPHTEC MP303-04 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC9000 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE3000-40 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE6000 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC CE7000-130AP Bedienungsanleitung

GRAPHTEC

GRAPHTEC LABERLROBO DLC1000 Bedienungsanleitung

GRAPHTEC

GRAPHTEC Craft ROBO CC100-20 Programmierhandbuch

GRAPHTEC

GRAPHTEC FC8600 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC CE2000-60 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC4200-50 Bedienungsanleitung

GRAPHTEC

GRAPHTEC Cutting PRO FC2230 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE7000 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC7000 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC FCX4000 SERIES Benutzerhandbuch

GRAPHTEC

GRAPHTEC FC2250 Series Bedienungsanleitung

GRAPHTEC

GRAPHTEC CE5000-60 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC4200-50 Bedienungsanleitung

GRAPHTEC

GRAPHTEC FC4500 Bedienungsanleitung

GRAPHTEC

GRAPHTEC CC300-20 Craft ROBO Bedienungsanleitung

GRAPHTEC

GRAPHTEC Craft ROBO CC100 Bedienungsanleitung

Beliebte Plotter Handbücher anderer Marken

MUTOH

MUTOH Kona 760 Bedienungsanleitung

HP 7475a Bedienungsanleitung

Vulcan-Hart

Vulcan-Hart FC-500VC Bedienungsanleitung

Roland

Roland TrueVIS VG-640 Betriebsanleitung

Furuno

Furuno RP-180 Bedienungsanleitung

Roland

Roland VersaCamm SP-540V Bedienungsanleitung

MIMAKI

MIMAKI CF2 Series Bedienungsanleitung

Ioline

Ioline Summit Bedienungsanleitung

Summa

Summa S CLASS Bedienungsanleitung

Gerber Technology

Gerber Technology GERBERplotter MP Series Bedienungsanleitung

Furuno

Furuno RP-17 Bedienungsanleitung

HP 7470A Bedienungsanleitung

SII

SII LP-1010 Bedienungsanleitung

Great Computer

Great Computer JII-61 Bedienungsanleitung

Roland

Roland VersaUv LEF - 12i Bedienungsanleitung

Lectra

Lectra Alys 120 Bedienungsanleitung

MUTOH

MUTOH Ultima SC-850D Bedienungsanleitung

Skycut

Skycut D Series Bedienungsanleitung