Grizzly H6144 Bedienungsanleitung

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL6904 PRINTED IN CHINA

34º ANGLE FINISH NAILER - 2½"

MODEL H6144

INSTRUCTION MANUAL

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazard-

ous conditions. This manual uses a series of symbols and signal words which

are intended to convey the level of importance of the safety messages. The

progression of symbols is described below. Remember that safety messages by

themselves do not eliminate danger and are not a substitute for proper accident

prevention measures.

Indicates a potentially hazardous situation which, if

not avoided, MAY result in minor or moderate injury.

It may also be used to alert against unsafe practices.

Indicates a potentially hazardous situation which, if

not avoided, COULD result in death or serious injury.

Indicates an imminently hazardous situation which, if

not avoided, WILL result in death or serious injury.

This symbol is used to alert the user to useful infor-

mation about proper operation of the equipment.

SAFETY

Safety Instructions for Machinery

1. READ THROUGH THE ENTIRE

MANUAL BEFORE STARTING

MACHINERY. Machinery presents

serious injury hazards to untrained

users.

2. MAKE SURE ALL GUARDS ARE

IN THEIR CORRECT PLACE AND

WORK CORRECTLY BEFORE

USING MACHINERY. NEVER

OPERATE MACHINE WITHOUT

GUARDS.

3. ALWAYS USE ANSI APPROVED

SAFETY GLASSES WHEN

OPERATING MACHINERY.

NOTICE

4. WEAR PROPER APPAREL. DO

NOT wear loose clothing, gloves,

neckties, rings, or jewelry which may

get caught in moving parts. Wear

protective hair covering to contain

long hair and wear non-slip foot-

wear.

5. NEVER OPERATE MACHINERY

WHEN TIRED, OR UNDER THE

INFLUENCE OF DRUGS OR

ALCOHOL. Be mentally alert at all

times when running machinery.

H6144 34° Angle Finish Nailer–2½"

-2--2-

6. ONLY ALLOW TRAINED AND

PROPERLY SUPERVISED PER-

SONNEL TO OPERATE MACHIN-

ERY. Make sure operation instruc-

tions are safe and clearly under-

stood.

7. KEEP CHILDREN AND VISITORS

AWAY. Keep all children and visi-

tors a safe distance from the work

area.

8. MAKE WORKSHOP CHILD

PROOF. Use padlocks, master

switches, and remove start switch

keys.

9. NEVER LEAVE WHEN MACHINE

IS RUNNING. Turn power OFF

and allow all moving parts to come

to a complete stop before leaving

machine unattended.

10. DO NOT USE IN DANGEROUS

ENVIRONMENTS. DO NOT use

machinery in damp, wet locations,

or where any flammable or noxious

fumes may exist.

11. KEEP WORK AREA CLEAN AND

WELL LIT. Clutter and dark shad-

ows may cause accidents.

12. USE A GROUNDED EXTENSION

CORD RATED FOR THE

MACHINE AMPERAGE.

Undersized cords overheat and

reduce voltage. Replace extension

cords if they become damaged. DO

NOT use extension cords for 220V

machinery.

13.

ALWAYS DISCONNECT FROM

POWER SOURCE BEFORE

SERVICING MACHINERY. Make

sure switch is in

OFF

position

before reconnecting.

14. MAINTAIN MACHINERY WITH

CARE. Keep blades sharp and

clean for best and safest per-

formance. Follow instructions for

lubricating and changing acces-

sories.

15. REMOVE ADJUSTING KEYS

AND WRENCHES. Make a habit

of checking for keys and adjust-

ing wrenches before turning ON

machinery.

16. CHECK FOR DAMAGED PARTS

BEFORE USING MACHINERY.

Check for binding and align-

ment of parts, broken parts, part

mounting, loose bolts, and any

other conditions that may affect

machine operation. Repair or

replace damaged parts.

17. USE RECOMMENDED

ACCESSORIES. Refer to the

instruction manual for recom-

mended accessories. The use of

improper accessories may cause

risk of injury.

18. DO NOT FORCE MACHINERY.

Work at the speed for which

the machine or accessory was

designed.

H6144 34° Angle Finish Nailer–2½" -3-

1. HAND INJURIES: Do not place your

hands near the nail point of entry. A

nail can deflect and tear through the

surface of the workpiece, puncturing

your hand or fingers.

2. COMBUSTIBLE GASES: Never

connect the nailer to pressurized

oxygen or other combustible gases

as a power source. Only use fil-

tered, lubricated, and regulated

compressed air.

3. SAFE HANDLING: Never point the

nailer at others! Do not keep the

trigger pulled when loading fasten-

ers, carrying, or holding tool. Carry

the nailer only by the handle, never

by any other part. Do not carry the

nailer by the air hose. Disconnect

the nailer from the air hose when

going up and down ladders.

4. CLEANING: Never use gasoline or

other flammable liquids to clean the

nailer; vapors in the nailer will ignite

by a spark and cause it to explode.

Additional Safety Instructions for Nailers

5. HOSE USAGE: Make sure your

air hose is designed for the tool

in use, is in good condition, and

is long enough to reach your work

without stretching. However, an

overly long air hose in the work

area may be a tripping hazard.

6. OPERATING QUESTIONS: If you

are not sure about the intended

operation, stop using the nailer.

Seek formal training or research

books or magazines that special-

ize in pneumatic tools.

7. MAINTENANCE: Always discon-

nect air from the nailer when ser-

vicing or installing nails. During

maintenance, a nailer connected

to air may fire accidentally, caus-

ing serious personal injury.

8. COMPRESSED AIR RATING: Do

not connect the nailer to com-

pressed air that exceeds 120 PSI.

9. CHECK VALVE: Do not use a

check valve or any other fitting that

allows air to remain in the tool.

H6144 34° Angle Finish Nailer–2½"

-4-

Operating this nailer can propel

objects into the air, causing imme-

diate eye damage. To protect your-

self, always wear American National

Standards Institute (ANSI) approved

safety glasses or goggles when oper-

ating this equipment. In addition, this

nailer discharges at 85-90 decibels.

To protect your hearing, always wear

ANSI approved ear protection when

operating this nailer.

Never point this nailer at yourself or

another person! Always pay attention

to the direction this nailer is pointed.

Use this tool with respect and caution

to lessen the possibility of operator or

bystander injury. Ignoring this warning

may result in serious personal injury.

No list of safety guidelines can be

complete. Every shop environment

is different. Always consider safety

first, as it applies to your individual

working conditions. Use this and

other tools with caution and respect.

Failure to do so could result in seri-

ous personal injury, damage to

equipment or poor work results.

H6144 34° Angle Finish Nailer–2½" -5-

INTRODUCTION

If you have any comments regarding this

manual, please write to us at the following

address:

Grizzly Industrial, Inc.

C/O Technical Documentation

P.O. Box 2069

Bellingham, WA 98227-2069

Most importantly, we stand behind our

tools. If you have any service questions or

parts requests, please call or write us at

the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

E-Mail: [email protected]

Web Site: http://www.grizzly.com

We are proud to offer the Grizzly Model

H6144 34º Angle Finish Nailer–2½". This

model is part of a growing Grizzly family of

fine pneumatic tools. When used accord-

ing to the guidelines set forth in this man-

ual, you can expect years of trouble-free,

enjoyable operation and proof of Grizzly’s

commitment to customer satisfaction.

The Model H6144 is designed to toenail

into corners and shoot at any angle. This

nailer is ideal for door, window, exterior,

and decorative trim, cabinet work, and fin-

ish paneling. The Model H6144 features

a 360° exhaust port, comfort grip rubber

handle, economical air consumption with

low noise, narrow nose for tight spots, and

quick jam release mechanism.

The specifications, details, and photo-

graphs in this manual represent the Model

H6144 as supplied when the manual was

prepared. However, owing to Grizzly’s pol-

icy of continuous improvement, changes

may be made at any time with no obliga-

tion on the part of Grizzly.

Foreword Contact Info

Machine Data

Nail Size .....................15 gauge ﬁnish nails

Nail Length ....................................1¼"-2½"

Magazine Capacity ........................ 40 Nails

Air Inlet ...........................................¼" NPT

Dimension ...............2.92" x 10.43" x 16.14"

Weight .............................................5¼ lbs.

Operating Pressure .................. 60-100 PSI

Read the manual before operation.

Become familiar with this nailer, its

safety instructions, and its operation

before beginning any work. Serious

personal injury may result if safety or

operational information is not under-

stood or followed.

H6144 34° Angle Finish Nailer–2½"

-6-

SET UP

Figure 1. Model H6144 inventory.

Unpacking

Your Model H6144 left our warehouse in

a carefully packed box. If you discover

the nailer is damaged after you have

signed for delivery, please immediately

call Customer Service at (570) 546-9663

for advice.

Save the containers and all packing mate-

rials for possible inspection by the car-

rier or its agent. Otherwise, filing a freight

claim can be difficult.

When you are completely satisfied with

the condition of the shipment, you should

inventory the equipment.

Inventory

After you remove the nailer case from the

box you should find the following.

Model H6144 Inventory (Figure 1)

A. 34° Finish Nailer−2½ ......................... 1

B. Safety Goggles ................................. 1

C. Oil ....................................................... 1

D. Hex Wrench 3MM .............................. 1

E. Hex Wrench 4MM .............................. 1

F. Hex Wrench 5MM .............................. 1

G. Case ................................................... 1

H6144 34° Angle Finish Nailer–2½" -7--7-

Compressed Air

System

The Model H6144 is designed to be oper-

ated at 60-100 PSI using clean, dry, regu-

lated, compressed air. DO NOT exceed

the maximum operating pressure for

your model.

Before using your new nailer, install a

1⁄4" NPT male quick connect fitting (not

included) on the nailer and a matching

1⁄4" NPT female fitting (not included) on

the air hose. Regulate the air pressure on

your air compressor to the minimum PSI

for your model.

An in-line filter/lubricator/regulator unit,

shown in Figure 2, can be installed and

should be located as close to the H6144

as possible.

This filter/lubricator/regulator unit will

protect your tool from damaging water

build-up, allow you to adjust and maintain

constant air pressure to your tool, and

save you the inconvenience of having to

manually lubricate your tool every time

you use it.

Quick

Connector

Quick

Coupler

Air Hose Quick

Coupler

Quick

Connector Oiler Filter

Regulator

Air

Compressor

Nailer

Figure 2 . Filter/Lubricator/Regulator Unit.

Check the current Grizzly catalog for avail-

ability of this unit. If you plan on install-

ing a filter/lubricator/regulator unit in your

compressed air system, always follow the

connection instructions that come with

the unit.

Exceeding the maximum permissible

operating pressure may cause the

nailer to explode, blowing metal frag-

ments in all directions. To protect

yourself from serious personal injury,

DO NOT allow your air compressor to

exceed the recommended pressure

when connected to this nailer!

H6144 34° Angle Finish Nailer–2½"

-8-

Safety Yoke

A safety yoke mechanism on the nose

of the nailer acts as a secondary safety

device. When the trigger is pressed, the

nailer will not fire until the safety yoke

mechanism is depressed.

Before you use your nailer for the first

time, check the safety yoke mechanism to

ensure proper function. To do this:

1. DISCONNECT NAILER FROM THE

AIR SUPPLY!

2. Make sure the magazine is empty and

contains no nails.

3. Make sure the trigger and the safety

yoke mechanism move up and down

without sticking.

4. Connect the nailer to the air supply.

5. Without pressing the trigger, depress

the safety yoke mechanism against a

scrap piece of wood that is clean and

free of any knots, nails, or other foreign

objects.

— If the nailer does not fire, then the

safety yoke mechanism is working

correctly.

— If the nailer does fire when you

do this, immediately disconnect the

nailer from the air supply and call

Grizzly Technical Support at (570)

546-9663 for help.

— If the nailer fires when the trigger

is pulled without the safety yoke

mechanism being depressed, then

the nailer is not working properly.

— If either of these conditions develop

after you have used your nailer for a

period of time, check the lubrication

of these mechanisms.

The safety yoke is a mechanical

device that can fail. Never rely on the

safety yoke mechanism as an excuse

to point the nailer at yourself or any

bystanders. Serious injury may occur.

H6144 34° Angle Finish Nailer–2½" -9-

OPERATIONS

When replacing nails in your Model

H6144, follow these guidelines:

Gauge: 15

Length: 11⁄4" -21⁄2"

Capacity: 40

Angle: 34°

NOTICE: A number of manufacturers'

nails may fit the Model H6144. However,

for best performance, we recommend you

use the following Grizzly nails:

G6085-G6088, G9545, G6090, G3693-

G3697.

To load your nailer:

1. DISCONNECT NAILER FROM THE

AIR SUPPLY!

2. Insert a nail stick into the T-slot at

the top of the magazine as shown in

Figure 3.

Figure 3. Loading finish nails into nailer.

Operating

If you have not read the safety instruc-

tions in this manual, do not operate

the nailer.

Before you operate your nailer, place one

drop of the included oil into the quick con-

nect fitting where the nailer connects to

the air supply.

To operate your nailer:

1. Connect the air supply to the quick

connect fitting.

2. To test for proper nail penetration, hold

the nailer perpendicular to the surface

of a piece of clean scrap wood that is

thick enough for the length of nails you

have loaded.

3. Depress the safety yoke mechanism

on your workpiece.

4. Before pulling the trigger, make sure

your free hand and other body parts

are positioned out of the way of a

potential path of a nail in case of

deflection.

Deflection is caused when grain irreg-

ularities, knots or foreign objects inside

the wood cause the nail to change its

path, resulting in the nail puncturing

the surface of the workpiece, as shown

in Figure 4.

3. Slide the nail stick all the way down to

the nose of the nailer.

Pusher

4. Pull the magazine pusher all the way

back, then let it come forward until it

rests against the end of the nail stick.

Andere Handbücher für H6144

Inhaltsverzeichnis

Andere Grizzly Nagelpistole Handbücher

Grizzly

Grizzly H5527 Bedienungsanleitung

Grizzly

Grizzly G6045 Bedienungsanleitung

Grizzly

Grizzly H7664 Kurzanleitung

Grizzly

Grizzly G2420 Bedienungsanleitung

Grizzly

Grizzly G6049 Bedienungsanleitung

Grizzly

Grizzly H6144 Kurzanleitung

Grizzly

Grizzly H2911 Bedienungsanleitung

Grizzly

Grizzly H6143 Kurzanleitung

Grizzly

Grizzly H7679 Bedienungsanleitung

Grizzly

Grizzly G2413 Bedienungsanleitung

Grizzly

Grizzly G6048 Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Grizzly

Grizzly H6143 Bedienungsanleitung

Grizzly

Grizzly H5527 Bedienungsanleitung

Grizzly

Grizzly H7665 Betriebsanleitung

Grizzly

Grizzly H2910 Bedienungsanleitung

Grizzly

Grizzly H5527 Bedienungsanleitung

Grizzly

Grizzly H6146 Kurzanleitung

Grizzly

Grizzly H7679 Betriebsanleitung

Grizzly

Grizzly 1 1/4" Brad Nailer T20568 Bedienungsanleitung

Grizzly

Grizzly H7945 Bedienungsanleitung

Grizzly

Grizzly H5571 Bedienungsanleitung

Grizzly

Grizzly H7665 Bedienungsanleitung

Grizzly

Grizzly T21347 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Black & Decker

Black & Decker 90514937 Bedienungsanleitung

Alfamacchine

Alfamacchine Minigraf 4 Handbuch