Guardian 15220 Bedienungsanleitung

Product Name: Screw-Down G-Rail Base

Instruction Manual

Part #: 15220

Do not throw away these instructions!

Read and understand these instructions before using equipment!

Introduction 1

Applicable Safety Standards 1

Worker Classifications 1

Product Specific Applications 1

Components and Specifications 2

Maintenance, Cleaning, and Storage 3

Inspection 3

Installation and Use 2

Inspection Log 3

Labels 3

Introduction

Thank you for purchasing a Guardian Fall

Protection Screw-Down G-Rail Base. This

manual must be read and understood in

its entirety, and used as part of an

employee training program as required

by OSHA or any applicable state agency.

This and any other included instructions

must be made available to the user of the

equipment. The user must understand how

to safely and effectively use the

Screw-Down G-Rail Base, and all fall safety

equipment used in combination with the

Screw-Down G-Rail Base.

User Information

Date of First Use:

Serial #:

Trainer:

User:

Applicable Safety Standards

When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926

Subpart M and OSHA 1910 standards for fall protection. Applicable standards and regulations depend on the

type of work being done, and also might include state-specific regulations. Consult regulatory agencies for

more information on fall protection systems and associated components.

Worker Classifications

CAUTION

Understand the following definitions of those who

work near or who may be exposed to fall hazards.

Qualified Person: A person with an accredited degree or certification, and with extensive experience or

sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall

protection and rescue systems.

Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be

responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,

and implementation. A person who is proficient in identifying existing and predictable fall hazards, and who

has the authority to stop work in order to eliminate hazards.

Authorized Person: A person who is assigned by their employer to work around or be subject to potential or

existing fall hazards.

It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all

applicable safety regulations are complied with.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Product Specific Applications

Fall Prevention: Screw-Down G-Rail Base may be used as a component in Fall Prevention

applications ONLY. Fall Prevention Systems are placed around the leading edges of any and all

fall hazards to prevent a worker from going over an edge, and may be used in substitute of

Fall Protection or safety netting systems. Installation requirements for Screw-Down G-Rail Base

set forth in this manual MUST be adhered to. Personal Fall Arrest, Work Positioning, Climbing,

Rescue, and any other systems must NEVER be connected to Fall Prevention Systems.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Maintenance, Cleaning, and Storage

If Screw-Down G-Rail Base fails inspection in any way, immediately remove it from service, and contact

Guardian to inquire about its return or repair.

Cleaning after use is important for maintaining the safety and longevity of Screw-Down G-Rail Base. Remove

all dirt, corrosives, and contaminants from Screw-Down G-Rail Base before and after each use. If Screw-Down

G-Rail Base cannot be cleaned with plain water, use mild soap and water, then rinse and wipe dry. NEVER

clean Screw-Down G-Rail Base with corrosive substances.

When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,

or other degrading elements.

Installation and Use

Components and Specifications

Materials:

powder-coated steel.

Prior to installation, plan your system:

Always ensure that complete G-Rail System, of which Screw-Down G-Rail Base is a component, is fully

compliant with all applicable OSHA regulations. Always adhere to all instructions provided with equipment.

G-Rail equipment instructions provided separately.

Assembly and use:

Concrete fastener hole (qty. 4)

Wood/metal fastener hole (qty. 20)

G-Rail post

installation location

Locking pin

Minimum substrate requirements:

• Wood: 5/8” CDX

• Metal: 24 gauge

• Concrete: 6”, 2,500 psi.

Substrate fastener requirements:

• Wood: #14-10, 2” wood deck screws (qty. 20).

• Metal: #14-10, 2“ metal deck screws (qty. 20).

• Concrete: ½” x 3” concrete bolts (qty. 4).

1. Select installation location for all Screw-Down G-Rail Bases. Ensure that spacing will facilitate installation

of applicable length G-Rails.

2. Maximum substrate slope is 4/12. This supersedes the 1/12 maximum slope for the G-Rail, which applies

to freestanding systems only.

3. Per substrate requirement, install all Screw-Down G-Rail Bases with all applicable fasteners. All fasteners

must be fully embedded in substrate.

4. Repeat installation process for all Screw-Down G-Rail Bases, ensuring that fully installed system will prevent

access to all applicable fall hazards.

5. Install G-Rail by inserting post into Screw-Down G-Rail Base and securing with locking pin.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Prior to EACH use, inspect Screw-Down G-Rail Base for deficiencies, including, but not limited to, corrosion,

deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating,

alteration, and missing or illegible labels. IMMEDIATELY remove Screw-Down G-Rail Base from service if defects

or damage are found. Ensure that applicable work area is free of all damage, including, but not limited to,

debris, rot, rust, decay, cracking, and hazardous materials.

At least every 12 months, a Competent Person other than the user must inspect Screw-Down G-Rail Base.

Competent Person inspections MUST be recorded in inspection log in instruction manual. The

Competent Person must sign their initials in the box corresponding to the month and year the

inspection took place.

During inspection, consider all applications and hazards Screw-Down G-Rail Base has been subjected to.

Inspection

Inspection Log

Date of First Use: __________________.

Product lifetime is indefinite, as long as it passes

pre-use and Competent Person inspections. User

must inspect prior to EACH use. Competent Person

other than user must complete formal inspection

at least every 12 months. Competent Person to

inspect and initial.

This inspection log must be specific to one Screw-Down G-Rail Base. Separate inspection logs must be

used for each Screw-Down G-Rail Base. All inspection records must be made visible and available to all

users at all times.

If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE.

85348 (Rev. A)

Labels

90923 (Rev. A)

Screw-Down

G-Rail Base

Part #: 15220

DOM:

Serial #:

Inhaltsverzeichnis

Andere Guardian Sicherheitsausrüstung Handbücher

Guardian

Guardian 42100 Bedienungsanleitung

Guardian

Guardian 00500 Bedienungsanleitung

Guardian

Guardian C7 Bedienungsanleitung

Guardian

Guardian 15176 Bedienungsanleitung

Guardian

Guardian 10785 Bedienungsanleitung

Guardian

Guardian 36030 Bedienungsanleitung

Guardian

Guardian ATOM-X RETRACTABLE TYPE FALL ARRESTER Bedienungsanleitung

Guardian

Guardian QSBOLT Bedienungsanleitung

Guardian

Guardian 42107 Bedienungsanleitung

Guardian

Guardian EXPOSURE OLAS Bedienungsanleitung

Guardian

Guardian G-CAS Bedienungsanleitung

Guardian

Guardian HALO Bedienungsanleitung

Guardian

Guardian MDS86012CHR Installationsanleitung

Guardian

Guardian 10785 Bedienungsanleitung

Guardian

Guardian XPLORER Bedienungsanleitung

Guardian

Guardian B7-COMFORT Bedienungsanleitung

Guardian

Guardian G-Rail Bedienungsanleitung

Guardian

Guardian 10920 Bedienungsanleitung

Guardian

Guardian CABLE CLIMBING SYSTEM Bedienungsanleitung

Guardian

Guardian 42110 Bedienungsanleitung

Guardian

Guardian CR3-EDGE SELF-RETRACTING LIFELINE Bedienungsanleitung

Guardian

Guardian Diablo SRL-LE Bedienungsanleitung

Guardian

Guardian G-SAL Bedienungsanleitung

Guardian

Guardian EyeSafe G1100 Montage- und Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung