Guardian Diablo SRL-LE Bedienungsanleitung

Product Name: Diablo 2.5 Cable Tie-Back SRL-LE

Instruction Manual

Part #: 11108; 11109

Do not throw away these instructions!

Read and understand these instructions before using equipment!

Introduction 1

Applicable Safety Standards 1

Worker Classifications 1

Safety Information 10

Product Specific Applications 2

Limitations 2 - 3

Components and Specifications 4

Maintenance, Cleaning, and Storage 7

Inspection 8

Installation and Use 4 - 6

Inspection Log 9

Labels 11

Introduction

Thank you for purchasing a Guardian Fall

Protection Diablo 2.5 Cable Tie-Back SRL-LE.

This manual must be read and understood

in its entirety, and used as part of an

employee training program as required by

OSHA or any applicable state agency.

This and any other included instructions

must be made available to the user of

the equipment. The user must understand

how to safely and effectively use the

Diablo 2.5 Cable Tie-Back SRL-LE, and all fall

safety equipment used in combination

with the Diablo 2.5 Cable Tie-Back SRL-LE.

User Information

Date of First Use:

Serial #:

Trainer:

User:

Applicable Safety Standards

When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926

Subpart M and OSHA 1910 standards for fall protection. Applicable standards and regulations depend on the

type of work being done, and also might include state-specific regulations. Consult regulatory agencies for

more information on fall protection systems and associated components.

Worker Classifications

CAUTION

Understand the following definitions of those who

work near or who may be exposed to fall hazards.

Qualified Person: A person with an accredited degree or certification, and with extensive experience or

sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall

protection and rescue systems.

Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be

responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,

and application. A person who is proficient in identifying existing and predictable fall hazards, and who has

the authority to stop work in order to eliminate hazards.

Authorized Person: A person who is assigned by their employer to work around or be subject to potential or

existing fall hazards.

It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all

applicable safety regulations are complied with.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Product Specific Applications

Restraint: Diablo 2.5 Cable Tie-Back SRL-LEs may be used in Restraint applications. Restraint systems

prevent workers from reaching the leading edge of a fall hazard. Always account for fully

deployed length of lanyard/SRL. Structure must withstand loads applied in the directions

permitted by the system of at least 1,000 lbs. No free fall is permitted. Restraint systems may

only be used on surfaces with slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal,

Chest, Side, Shoulder.

WARNING

Use of equipment in unintended applications may result in serious

injury or death. Maximum 1 attachment per connection point.

Personal Fall Arrest: Diablo 2.5 Cable Tie-Back SRL-LEs may be used in Personal Fall Arrest

applications as a component of a MAXIMUM 1 Personal Fall Arrest System (PFAS). Structure must

withstand loads applied in the directions permitted by the system of at least 5,000 lbs. Applicable

D-ring: Dorsal.

• Free fall, LE Use: Maximum 5’.

• Free fall, non-LE Use: Maximum 2’.

For all applications, worker weight capacity range (including all clothing, tools, and equipment):

LE Use: 130-310 lbs.

Non-LE Use: 130-420 lbs.

Limitations

Fall Clearance: There must be sufficient

clearance below the anchorage connector

to arrest a fall before the user strikes the

ground or an obstruction. When calculating

fall clearance, account for a MINIMUM 2’

safety factor, deceleration distance, user

height, length of lanyard/SRL, harness

stretch, and all other applicable factors.

Diagram shown is an example fall

clearance calculation ONLY.

Swing Falls: Prior to installation or use, make

considerations for eliminating or minimizing

all swing fall hazards. Swing falls occur when

the anchor is not directly above the location

where a fall occurs. Always work as close to

in line with the anchor point as possible.

Swing falls significantly increase the likelihood

of serious injury or death in the event of a fall.

Diablo 2.5 Cable Tie-Back SRL-LE recommended

fall clearance (does not factor in any potential

swing fall hazards). Clearance numbers specified

based on lifeline installed vertically overhead

and in-line with worker:

• LE Use: 13‘-17’

• Non-LE Use: 5½’ (no free fall) to 7½’ (maximum 2’ free fall)

*Eliminate Swing Fall whenever

possible! If Swing Fall exists,

always account for additional

fall clearance.

Anchor Point

at Foot Level

Class B SRL

SRL-LE

4.5’

8.5’

5’

2’

1.5’

Work Surface

4.5’

2’

1.5’

2’

max.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Components and Specifications

Compatibility: When making connections with Diablo 2.5 Cable Tie-Back SRL-LE, eliminate all possibility of

roll-out. Roll-out occurs when interference between a hook and the attachment point causes the hook gate to

unintentionally open and release. All connections must be selected and deemed compatible with Diablo Cable

Tie-Back SRL-LE by a Competent Person. All connector gates must be self-closing and self-locking, and

withstand minimum loads of 3,600 lbs. See the following for examples of compatible/incompatible

connections:

Connector

closed and

locked to

D-ring. OK.

Two or more

snap hooks or

carabiners

connected to

each other. NO.

Two connectors

to same

D-ring. NO.

Connector

directly to

horizontal

lifeline. NO.

Connector

to integral

lanyard.

NO.

Connector

directly to

webbing.

NO.

Incompatible

or irregular

application,

which may

increase risk

of roll-out. NO.

Part # Description

11108

11109

Diablo 2.5 Cable Tie-Back SRL-LE w/Steel Snap Hook End. Single Leg.

Diablo 2.5 Cable Tie-Back SRL-LE w/Steel Snap Hook Ends. Dual Leg Kit.

Materials: galvanized steel, aluminum,

glass-filled nylon, rubber, polyester, and nylon.

Average arrest force: 900 lbs.

Maximum arrest force:1,800 lbs.

Maximum deceleration distance (non-LE): 54”.

Maximum deceleration distance (LE): 54” - 102”.

Lifeline length: 8’.

Tie-back webbing length: 3’.

Cable

Lifeline

Tie-Back

Snap Hook

SRL Bracket

Shock Absorber/

Back Pad

Housing

Tie-Back

Webbing

Rubber

Stopper

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Installation and Use

WARNING

In tie-back applications, snap hook must ONLY be attached

to tie-back webbing. NEVER attach snap hook to cable lifeline.

1. All PFAS components must be selected and deemed compatible with Diablo 2.5 Cable Tie-Back SRL-LE by

Competent Person.

2. Ensure structure to which Diablo 2.5 Cable Tie-Back SRL-LE is to be attached, and on which work is to be

performed, is free of all hazards, including, but not limited to, debris, rot, rust, sharp or abrasive edges and

surfaces, and hazardous materials.

3. Eliminate or minimize all risk of swing fall hazard.

4. Ensure 100% tie-off will be maintained at all times, which may require the use of a back-up or

supplementary fall protection system.

5. Always minimize lifeline contact with sharp or abrasive edges and surfaces.

6. For Dual-Leg Kit, only work with one leg attached, except when transitioning between anchor points. When

transitioning between anchor points, first connect second leg to applicable anchor point, then disconnect other

leg from previous anchor point prior to beginning any work. Always ensure 100% tie-off is maintained.

7. Diablo 2.5 Cable Tie-Back SRL-LE may be used in either tie-back or standard applications. Adhere to the

applicable method of installation and use.

Always use Diablo 2.5 Cable Tie-Back SRL-LE in combination with anchor

point that eliminates as much slack in lifeline as possible. Competent

Person must ensure that anchor point location will not introduce

potential free fall greater than what is permitted by the system.

WARNING

To install Diablo 2.5 Cable Tie-Back SRL-LE to harness:

1. Compress and hold both release buttons on SRL Bracket and slide pin to open position. Do not attempt to

open or otherwise modify bracket that is connected to Diablo 2.5 Cable Tie-Back SRL-LE.

Release

buttons

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

2. At web loop immediately beneath harness dorsal D-ring, slide SRL Bracket pin through loop and lock closed.

It may be necessary to slightly loosen web loop to accommodate pin. Always re-tighten web loop after install.

Depending on SRL Bracket design, either ensure green indicator IS fully visible, or that red indicator

IS NOT visible.

Note: With Diablo 2.5 Cable Tie-Back SRL-LE attached to harness as shown, it is permitted to connect a

separate connecting device to the harness dorsal D-ring. However, never work with more than one

connecting device attached to an anchorage connector at any time.

SRL Bracket installed at web loop.

Green indicator visible -

OK to use.

Red indicator visible -

DO NOT use.

Diablo SRL-LE back pad hook and loop fastener straps

secured around harness shoulder straps.

3. Secure Diablo SRL-LE back pad around harness shoulder straps with provided hook and loop fastener straps

as shown.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

SRL-LE Additional Use Instructions:

ALWAYS adhere to the following warnings and specifications when using SRL-LEs.

WARNING

Tie-Back:

A) Attach Diablo 2.5 Cable Tie-Back

SRL-LE to harness.

B) Wrap Diablo 2.5 Cable Tie-Back

SRL-LE tie-back webbing around

selected structural anchor. Ensure

potential free fall does not exceed

what is permitted by the system, as

determined by Competent Person.

C) Attach snap hook to

webbing BELOW rubber stopper.

NEVER attach tie-back hook to

cable lifeline or anything other

than tie-back webbing.

Standard:

A) Attach Diablo 2.5 Cable Tie-Back SRL-LE to harness.

B) Attach snap hook to compatible overhead anchorage connector. Ensure potential free fall does not

exceed what is permitted by the system, as determined by Competent Person.

Snap hook attached to

tie-back webbing. OK.

NEVER attach snap

hook to cable lifeline.

Diablo 2.5 Cable Tie-Back SRL-LEs are tested and certified for horizontal use over a steel edge without burrs. Diablo

Cable Tie-Back SRL-LEs may be used over similar surfaces, such as metal sheeting or other steel formations.

The allowable angle of redirection of the lifeline portion of Diablo 2.5 Cable Tie-Back SRL-LEs at the leading edge

of a fall hazard MUST be at least 90° (see Image 1).

Anchor point MUST be situated no lower than the leading edge of applicable fall hazard(s).

Prior to use, a Competent Person MUST calculate adequate fall clearance (see pg. 3).

ALWAYS attach to anchorage connector that will allow for required setback distance (see Image 2).

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Setback Distance

Image 1 Image 2

Leading Edge

X≤90°

X≥90°

Setback distance: As determined by product testing, Guardian Fall Protection Diablo 2.5 Cable Tie-Back

SRL-LEs are not required to be setback any specific distance from the leading edge of applicable fall

hazard(s).

Diablo 2.5 Cable Tie-Back SRL-LE may be used in combination with horizontal lifelines. All installation, set-up, and

use of horizontal lifelines must be done under the supervision of a Qualified Person.

NEVER work on the far side of an opening that is opposite the Diablo 2.5 Cable Tie-Back SRL-LE anchorage point.

In the event of a fall over the edge, special rescue measures may be necessary. Always account for use of

Diablo 2.5 Cable Tie-Back SRL-LE in job site rescue plan developed by job site Competent Person.

Maintenance, Cleaning, and Storage

If Diablo 2.5 Cable Tie-Back SRL-LE fails inspection in any way, immediately remove it from service, and contact

Guardian to inquire about its return or repair.

Cleaning after use is important for maintaining the safety and longevity of Diablo 2.5 Cable Tie-Back SRL-LE.

Remove all dirt, corrosives, and contaminants from Diablo 2.5 Cable Tie-Back SRL-LE before and after each use. If

Diablo 2.5 Cable Tie-Back SRL-LE cannot be cleaned with plain water, use mild soap and water, then rinse and wipe

dry. NEVER clean Diablo 2.5 Cable Tie-Back SRL-LE with corrosive substances.

When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,

or other degrading elements.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Prior to EACH use, inspect Diablo 2.5 Cable Tie-Back SRL-LE for deficiencies, including, but not limited to,

corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive

heating, alteration, broken stitching, fraying, bird-caging, and missing or illegible labels.

Pay careful attention to cable swage (located beneath rubber stopper) and ensure no damage is present at

location where swage contacts lifeline. IMMEDIATELY remove Diablo 2.5 Cable Tie-Back SRL-LE from service if

defects or damage are found, or if exposed to forces of fall arrest. Ensure fall arrest indicator (broken stitching

at location shown below) is not deployed. During inspection, consider all applications and hazards Diablo 2.5

Cable Tie-Back SRL-LE has been subjected to.

Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,

cracking, and hazardous materials. Ensure that selected work area will support the application-specific

minimum loads set forth in this instruction manual. Work area MUST be stable.

At least every 12 months, a Competent Person other than the user must inspect Diablo 2.5 Cable

Tie-Back SRL-LE. Competent Person inspections MUST be recorded in inspection log in instruction

manual and on equipment inspection grid label. The Competent Person must sign their initials in the

box corresponding to the month and year the inspection took place.

Immediately remove from service if indicator stitching shows any signs of damage:

Inspection

Intact indicator stitching - OK to use.

Broken/damaged indicator stitching - Immediately remove from service!

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Inspection Log

Date of First Use: __________________.

Product lifetime is indefinite, as long as it passes pre-use and Competent Person inspections. User must

inspect prior to EACH use. Competent Person other than user must complete formal inspection at least

every 12 months. Competent Person to inspect and initial.

This inspection log must be specific to one Diablo 2.5 Cable Tie-Back SRL-LE. Separate inspection logs must

be used for each Diablo 2.5 Cable Tie-Back SRL-LE. All inspection records must be made visible and

available to all users at all times.

If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Guardian Sicherheitsausrüstung Handbücher

Guardian

Guardian FABXR Bedienungsanleitung

Guardian

Guardian MDS89745RA Bedienungsanleitung

Guardian

Guardian Halo SRL Series Bedienungsanleitung

Guardian

Guardian Halo Big Block SRL Bedienungsanleitung

Guardian

Guardian 42120 Bedienungsanleitung

Guardian

Guardian HALO BIG BLOCK SRL-LE Bedienungsanleitung

Guardian

Guardian Retractable HLL Bedienungsanleitung

Guardian

Guardian B7-COMFORT Bedienungsanleitung

Guardian

Guardian G-SAL Bedienungsanleitung

Guardian

Guardian ATOM-X RETRACTABLE TYPE FALL ARRESTER Bedienungsanleitung

Guardian

Guardian 00230 Bedienungsanleitung

Guardian

Guardian 15220 Bedienungsanleitung

Guardian

Guardian XPLORER Bedienungsanleitung

Guardian

Guardian G-Rail Bedienungsanleitung

Guardian

Guardian 15176 Bedienungsanleitung

Guardian

Guardian 42102 Bedienungsanleitung

Guardian

Guardian Truss Boss Anchor Bedienungsanleitung

Guardian

Guardian 00240 Bedienungsanleitung

Guardian

Guardian FABX Bedienungsanleitung

Guardian

Guardian WEB HORIZONTAL LIFELINE Bedienungsanleitung

Guardian

Guardian CR5 Bedienungsanleitung

Guardian

Guardian CR3-EDGE SELF-RETRACTING LIFELINE Bedienungsanleitung

Guardian

Guardian 01205 Bedienungsanleitung

Guardian

Guardian 10736 Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung