Guardian 10785 Bedienungsanleitung

Product Name: Cross Arm Strap/Cable Choker

Instruction Manual

Part #: 10785; 10786; 10787; 10788; 10790; 10791; 10792; 10793; 10794;

10420; 10421; 10422; 10460; 10461; 10462; 10430; 10431; 10432; 10470;

10471; 10472; 10410; 10411; 10412; 10450; 10451; 10452; 10400; 10401;

10402; 10440; 10441; 10442; 01640; 01630; 01625; 01620

Do not throw away these instructions!

Read and understand these instructions before using equipment!

Table of Contents

Introduction 1-2

Applicable Safety Standards 2

Worker Classifications 2

Safety Information 3-4

Product Specific Applications 6

Limitations 7-9

Components and Specifications 10

Maintenance, Cleaning, and Storage 5

Inspection 5

Installation and Use 11

Inspection Log 13

Notes 13

Introduction

Thank you for purchasing a Guardian Fall Protection Cross Arm Strap/Cable Choker. This manual

must be read and understood in its entirety, and used as part of an employee training program

as required by OSHA or any applicable state agency.

This and any other included instructions must be made available to the user of the equipment.

The user must understand how to safely and effectively use the Cross Arm Strap/Cable Choker,

and all fall safety equipment used in combination with the Cross Arm Strap/Cable Choker.

Labels 12

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 USA phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

User Information

Date of First Use:

Serial #:

Trainer:

User:

Applicable Safety Standards

When used according to instruction specifications, this product meets or exceeds all applicable

OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1-2007, and ANSI A10.32-2012 standards for fall

protection. Applicable standards and regulations depend on the type of work being done, and

also might include state-specific regulations. Consult regulatory agencies for more information

on personal fall arrest systems and associated components.

Worker Classifications

CAUTION

Understand the following definitions of those who

work near or who may be exposed to fall hazards.

Qualified Person: A person with an accredited degree or certification, and with extensive

experience or sufficient professional standing, who is considered proficient in planning and

reviewing the conformity of fall protection and rescue systems.

Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER

to be responsible for all elements of a fall safety program, including, but not limited to, its

regulation, management, and application. A person who is proficient in identifying existing and

predictable fall hazards, and who has the authority to stop work in order to eliminate hazards.

Authorized Person: A person who is assigned by their employer to work around or be subject to

potential or existing fall hazards.

It is the responsibility of a Qualified or Competent person to supervise the job site and

ensure all applicable safety regulations are complied with.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 USA phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Safety Information

Do not alter equipment.

Do not misuse equipment.

Workplace conditions, including, but not limited to, flame, corrosive chemicals, electrical shock,

sharp objects, machinery, abrasive substances, weather conditions, and uneven surfaces, must

be assessed by a Competent Person before fall protection equipment is selected.

The analysis of the workplace must anticipate where workers will be performing their duties,

the routes they will take to reach their work, and the potential and existing fall hazards they

may be exposed to.

Fall protection equipment must be chosen by a Competent Person. Selections must account for

all potential hazardous workplace conditions.

All fall protection equipment should be purchased new and in an unused condition.

Fall protection systems must be selected and installed under the supervision of a Competent

Person, and used in a compliant manner.

Fall protection systems must be designed in a manner compliant with all federal, state, and

safety regulations.

Unless explicitly stated otherwise, the maximum allowable free fall distance for lanyards must

not exceed 6’. No free fall allowed for non-LE SRLs. SRLs must arrest falls within 54”.

Forces applied to anchors must be calculated by a Competent Person.

Harnesses and connectors selected must be compliant with manufacturer’s instructions, and

must be of compatible size and configuration.

A pre-planned rescue procedure in the case of a fall is required. The rescue plan must be project-

specific. The rescue plan must allow for employees to rescue themselves, or provide an

alternative means for their prompt rescue.

Store rescue equipment in an easily accessible and clearly marked area.

Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use

equipment must be provided by a Competent Person.

Training must include the ability to recognize fall hazards, minimize the likelihood of fall hazards,

and the correct use of personal fall arrest systems.

Failure to understand and comply with safety regulations may result in

serious injury or death. Regulations included herein are not all-inclusive,

are for reference only, and are not intended to replace a Competent

Person’s judgment or knowledge of federal or state standards.

WARNING

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 USA phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or

equipment, unless explicitly certified for such use.

Maintenance of equipment must be done according to manufacturer’s instructions. Equipment

instructions must be retained for reference.

Prior to EACH use, all equipment in a fall protection system must be inspected for any potential

or existing deficiencies that may result in its failure or reduced functionality. IMMEDIATELY

remove equipment from service if any deficiencies are found.

Equipment must be inspected by a Competent Person at least every six months. These

inspections must be documented in equipment instruction manual and on equipment inspection

grid label.

Equipment must be inspected for defects, including, but not limited to, the absence of required

labels or markings, improper form/fit/function, evidence of cracks, sharp edges, deformation,

corrosion, excessive heating, alteration, excessive wear, fraying, knotting, abrasion, and absence

of parts.

Equipment that fails inspection in any way must immediately be removed from use, or repaired

by an entity approved by the manufacturer.

No on-site repair of equipment unless explicitly permitted by Guardian Fall Protection.

Equipment subjected to forces of fall arrest must immediately be removed from use.

Snap hooks, carabiners, and other connectors must be selected and applied in a compatible

fashion. All risk of disengagement must be eliminated. All snap hooks and carabiners must be

self-locking and self-closing, and must never be connected to each other.

Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a

doctor if there is any reason to doubt a user’s ability to withstand and safely absorb fall arrest

forces or perform set-up of equipment.

Pregnant women and minors must not use this equipment.

Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall

suspension may result in serious injury or death. Use trauma relief straps to reduce the effects of

suspension trauma.

Allowable individual worker weight limit (including all equipment), unless explicitly stated

otherwise, is 130-310 lbs.

Maintenance, Cleaning, and Storage

Repairs to Cross Arm Strap/Cable Choker can only be made by a Guardian Fall Protection

representative or an entity authorized by Guardian. Contact Guardian for all maintenance and

repair needs at: 1-800-466-6385. If a Cross Arm Strap/Cable Choker fails inspection in any way,

immediately remove it from service, and contact Guardian to inquire about its return or repair.

Cleaning after use is important for maintaining the safety and longevity of Cross Arm

Strap/Cable Choker. Remove all dirt, corrosives, and contaminants from Cross Arm Strap/Cable

Choker before and after each use. If Cross Arm Strap/Cable Choker cannot be cleaned with plain

water, use mild soap and water, then rinse and wipe dry. NEVER clean Cross Arm Strap/Cable

Choker with corrosive substances.

When not in use, store equipment where it will not be affected by heat, light, excessive

moisture, chemicals, or other degrading elements.

KEEP INSTRUCTIONS AVAILABLE FOR REFERENCE. Record Date of First Use.

Prior to EACH use, inspect Cross Arm Strap/Cable Choker for deficiencies, including, but not

limited to, corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint

buildup, excessive heating, alteration, broken stitching, fraying, bird-caging, and missing or

illegible labels. IMMEDIATELY remove Cross Arm Strap/Cable Choker from service if defects or

damage are found, or if exposed to forces of fall arrest.

Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot,

rust, decay, cracking, and hazardous materials. Ensure that selected work area will support the

application-specific minimum loads set forth in this instruction manual. Work area MUST be

stable.

At least every 6 months, a Competent Person other than the user must inspect Cross Arm

Strap/Cable Choker. Competent Person inspections MUST be recorded in inspection log in

instruction manual and on equipment inspection grid label. The Competent Person must

sign their initials in the box corresponding to the month and year the inspection took

place.

During inspection, consider all applications and hazards Cross Arm Strap/Cable Choker have

been subjected to.

Inspection

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 USA phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Product Specific Applications

Personal Fall Arrest: Cross Arm Strap/Cable Choker may be used to support a

MAXIMUM 1 Personal Fall Arrest System (PFAS) for use in Fall Arrest applications.

Structure must withstand loads applied in the directions permitted by the system

of at least 5,000 lbs. Maximum free fall is 6‘, or up to 12’ if used in combination

with equipment explicitly certified for such use. Applicable D-ring: Dorsal.

Restraint: Cross Arm Strap/Cable Choker may be used in Restraint applications.

Restraint systems prevent workers from reaching the leading edge of a fall hazard.

Always account for fully deployed length of lanyard/SRL. Structure must withstand

loads applied in the directions permitted by the system of at least 1,000 lbs. No

free fall is permitted. Restraint systems may only be used on surfaces with slopes

up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal, Chest, Side, Shoulder.

WARNING

Use of equipment in unintended applications may result in serious

injury or death. Maximum 1 attachment per connection point.

For all applications: worker weight capacity range

(including all clothing, tools, and equipment) is 130-310 lbs.,

or up to 420 lbs. if used in combination with

equipment explicitly certified for such use.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 USA phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

FALL CLEARANCE CALCULATION

Lanyard length

(6’ total)

Safety factor

(3’ total)

Deceleration

distance (4’ total)

Height of harness

dorsal D-ring from

worker’s feet

(6’ total)

Required

distance

from

anchorage

(19’ total)

Limitations

Fall Clearance: There must be sufficient clearance below the anchorage connector to arrest a fall

before the user strikes the ground or an obstruction. When calculating fall clearance, account for

a MINIMUM 3’ safety factor, deceleration distance, user height, length of lanyard/SRL, and all

other applicable factors. Diagram shown is an example fall clearance calculation ONLY.

Swing Falls: Prior to installation or use, make considerations for eliminating or minimizing all

swing fall hazards. Swing falls occur when the anchor is not directly above the location where a

fall occurs. Always work as close to in line with the anchor point as possible. Swing falls

significantly increase the likelihood of serious injury or death in the event of a fall.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 USA phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Compatibility: When making connections with Cross Arm Strap/Cable Choker, eliminate all

possibility of roll-out. Roll-out occurs when interference between a hook and the attachment

point causes the hook gate to unintentionally open and release. All connections must be

selected and deemed compatible with Cross Arm Strap/Cable Choker by a Competent Person.

All connector gates must be self-closing and self-locking, and withstand minimum loads of

3,600 lbs. See the following for examples of compatible/incompatible connections:

Connector

closed and

locked to

D-ring. OK.

Two or more

snap hooks or

carabiners

connected to

each other. NO.

Two connectors

to same

D-ring. NO.

Connector

directly to

horizontal

lifeline. NO.

Connector

to integral

lanyard.

NO.

Connector

directly to

webbing.

NO.

Application

that places

load on gate.

NO.

Incompatible

or irregular

application,

which may

increase risk

of roll-out. NO.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 USA phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Andere Handbücher für 10785

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Guardian Sicherheitsausrüstung Handbücher

Guardian

Guardian 42100 Bedienungsanleitung

Guardian

Guardian 00260 Bedienungsanleitung

Guardian

Guardian WEB HORIZONTAL LIFELINE Bedienungsanleitung

Guardian

Guardian B7-COMFORT Bedienungsanleitung

Guardian

Guardian Diablo SRL-LE Bedienungsanleitung

Guardian

Guardian 10870 Bedienungsanleitung

Guardian

Guardian 01205 Bedienungsanleitung

Guardian

Guardian G-Rail Bedienungsanleitung

Guardian

Guardian CR3-EDGE SELF-RETRACTING LIFELINE Bedienungsanleitung

Guardian

Guardian EXPOSURE LAS Bedienungsanleitung

Guardian

Guardian PBH05 Bedienungsanleitung

Guardian

Guardian DIABLO 10967 Bedienungsanleitung

Guardian

Guardian Diablo 2.5 Cable SRL-LE Bedienungsanleitung

Guardian

Guardian 42107 Bedienungsanleitung

Guardian

Guardian XPLORER Bedienungsanleitung

Guardian

Guardian 15220 Bedienungsanleitung

Guardian

Guardian 42120 Bedienungsanleitung

Guardian

Guardian CR5 Bedienungsanleitung

Guardian

Guardian VERTICAL LIFELINE Bedienungsanleitung

Guardian

Guardian 10910 Bedienungsanleitung

Guardian

Guardian 10736 Bedienungsanleitung

Guardian

Guardian MDS86012CHR Installationsanleitung

Guardian

Guardian HALO Bedienungsanleitung

Guardian

Guardian 00230 Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung