H3C LSQM1CGS2QSA0 Bedienungsanleitung

H3C LSQM1CGS2QSA0 interface card

user manual-6PW101

▌Introduction

Overview

The LSQM1CGS2QSA0 interface card provides two QSFP28 ports

and two QSFP+ ports.

Figure 1 Front panel

(1) QSFP+ port LED (2) QSFP28 port LED

(3) QSFP28 port (4) QSFP+ port

QSFP+ ports

You can install the following transceiver modules and cables in the

QSFP+ ports on the card:

•QSFP+ transceiver modules in Table 1 and Table 2.

•QSFP+ cables in Ta ble 3.

•QSFP+ to SFP+ cables in Table 4.

Table 1 QSFP+ transceiver modules available for the QSFP+

ports (1)

QSFP+ transceiver module Central

wavelength (nm) Connector

QSFP-40G-SR4-MM850 850 MPO

QSFP-40G-CSR4-MM850 850 MPO

QSFP-40G-LR4-WDM1300

Four lanes:

•1271

•1291

•1311

•1331

Table 2 QSFP+ transceiver modules available for the QSFP+

ports (2)

QSFP+

transceiver

module

Cable/fiber

diameter

(µm)

Modal

bandwidth

(MHz × km)

Max transmission

distance

QSFP-40G-S

R4-MM850

Multi-mode,

50/125

2000 100 m (328.08 ft)

4700 150 m (492.12 ft)

QSFP-40G-C

SR4-MM850

Multi-mode,

50/125

2000 300 m (984.25 ft)

4700 400 m (1312.33 ft)

QSFP-40G-LR

4-WDM1300

Single-mode,

9/125 N/A 10 km (6.21 miles)

Table 3 QSFP+ cables available for the QSFP+ ports

QSFP+ cable Cable length Data rate

LSWM1QSTK2 5 m (16.40 ft) 40 Gbps

Table 4 QSFP+ to SFP+ cables available for the QSFP+ ports

QSFP+ to SFP+ cable Cable length Data rate

LSWM1QSTK3 1 m (3.28 ft)

40 Gbps

LSWM1QSTK4 3 m (9.84 ft)

LSWM1QSTK5 5 m (16.40 ft)

NOTE:

s a best practice, use H3C QSFP+ transceiver modules, QSFP+

cables, and QSFP+ to SFP+ cables for the QSFP+ ports on the

LSQM1CGS2QSA0 interface card. The H3C QSFP+ transceiver

modules and cables available for the card are subject to change

over time. For the most recent list of H3C QSFP+ transceiver

modules and cables available for the card, contact H3C Support o

marketing staff.

For more information about H3C QSFP+ transceiver modules,

QSFP+ cables, and QSFP+ to SFP+ cables, see H3C Transceiver

Modules User Guide at www.h3c.com.hk.

QSFP28 ports

You can install the following transceiver modules and cables in the

QSFP28 ports on the card:

•QSFP+ transceiver modules in Table 1 and Table 2.

•QSFP+ cables in Ta ble 3.

•QSFP28 transceiver modules in Table 5 and Table 6.

Table 5 QSFP28 transceiver modules available for the QSFP28

ports (1)

QSFP28 transceiver

module

Central wavelength

(nm) Connector

QSFP-100G-SR4-MM850 850

MPO (PC

polished,

12-core)

Table 6 QSFP28 transceiver modules available for the QSFP28

ports (2)

QSFP+

transceiver

module

Cable/fiber

diameter

(µm)

Modal

bandwidth

(MHz × km)

Max

transmission

distance

QSFP-100G-S

R4-MM850

Multi-mode,

50/125

4700 100 m (328.08 ft)

2000 70 m (229.66 ft)

NOTE:

s a best practice, use H3C QSFP28 transceiver modules for the

QSFP28 ports on the LSQM1CGS2QSA0 interface card. The H3C

QSFP28 transceiver modules available for the card are subject to

change over time. For the most recent list of H3C QSFP28

transceiver modules available for the card, contact H3C Support

or marketing staff.

For more information about H3C QSFP28 transceiver modules, see

H3C Transceiver Modules User Guide at www.h3c.com.hk.

LEDs

Table 7 describes QSFP28 port LEDs and QSFP+ port LEDs on the

front panel.

Table 7 QSFP28 port LED description

LED status Description

Steady green

A transceiver module is installed in the port. The

port is operating at 100 Gbps, and a link is present

on the port.

Flashing green The port is sending or receiving data at 100 Gbps.

Steady yellow

A transceiver module is installed in the port. The

port is operating at 10/40 Gbps, and a link is

present on the port.

Flashing

yellow (3 Hz)

The port is sending or receiving data at 10/40

Gbps.

LED status Description

Off No transceiver module is installed in the port, or

no link is present on the port.

Table 8 QSFP+ port LED description

LED status Description

Steady green

A transceiver module is installed in the port. The

port is operating at 40 Gbps, and a link is present

on the port.

Flashing green The port is sending or receiving data at 40 Gbps.

Steady yellow

A transceiver module is installed in the port. The

port is operating at 10 Gbps, and a link is present

on the port.

Flashing yellow The port is sending or receiving data at 10 Gbps.

Off No transceiver module is installed in the port, or

no link is present on the port.

NOTE:

The QSFP28 port LEDs and QSFP+ port LEDs are not affected by

the port LED mode switching button on your switch. For more

information about the port LED mode switching button, see the

installation guide for the switch.

▌Installing and removing the card

CAUTION:

•Before you install or remove the card, wear an ESD wrist strap

and make sure the strap makes good skin contact and is

reliably grounded.

•To avoid device damage, do not use excessive force when you

install or remove the card.

Installing the card

1. Remove the filler panel (if any) from the target slot.

Keep the removed filler panel secure for future use.

2. Unpack the interface card.

Figure 2 LSQM1CGS2QSA0 interface card

(1) Ejector lever (2) Latch

3. Press the latch on the card to release the ejector lever.

4. As shown by callout 1 in Figure 3, insert the card slowly into the

slot along the guide rails.

5. Rotate inward the ejector lever as shown by callout 2 in Figure 3

until the latch locks the ejector lever in place.

Figure 3 Installing the LSQM1CGS2QSA0 interface card

Removing the card

CAUTION:

To avoid cable damage, remove the cables from the card before

removing the card.

To remove the card:

1. Prepare an anti-static bag.

2. Press the latch to release the ejector lever

3. Rotate outward the ejector lever as shown by callout 1 in Figure 4.

4. Pull out the interface card slowly out of the interface card slot, as

shown by callout 2 in Figure 4.

5. Place the removed interface card in the anti-static bag.

6. If you are not to install a new card, install a filler panel in the slot to

prevent dust and ensure good ventilation in the device.

Figure 4 Removing the LSQM1CGS2QSA0 interface card

Installing and removing QSFP28/QSFP+ transceiver

modules and cables

For information about installing and removing QSFP28/QSFP+

transceiver modules and cables, see H3C QSFP+[QSFP28]

Transceiver Modules and Cables Installation Guide

at www.h3c.com.hk.

Verifying the installation

After the installation is complete, determine whether the card is

operating correctly.

If the card fails to operate correctly, perform the following steps:

1. Reinstall the card following the installation procedures described

in this document.

2. If the problem persists, contact H3C Support.

▌Technical support

New H3C Technologies Co., Ltd. provides customers with

comprehensive technical support and service. If you purchase the

products from the sales agent of New H3C Technologies Co., Ltd.,

please contact our sales agent or technical personnel.

Website: http://www.h3c.com.hk

E-mail: [email protected]

BOM: 3101A0LM

Inhaltsverzeichnis

Andere H3C Steuereinheit Handbücher

H3C

H3C LSQ1LBSC0 Bedienungsanleitung

H3C

H3C NSQ1TGS32SF0 Bedienungsanleitung

H3C

H3C PSR300-12A Series Bedienungsanleitung

H3C

H3C R6900-FAN Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM-200 Bedienungsanleitung

H3C

H3C EWPA1PCID Bedienungsanleitung

H3C

H3C LSBM1WCM2A0 Bedienungsanleitung

H3C

H3C NSQM1FWDFGC1 Bedienungsanleitung

H3C

H3C S9500E LSR1FW2A1 Bedienungsanleitung

H3C

H3C SecPath M9000 NSQM1MBFEA0 Bedienungsanleitung

H3C

H3C LSVM152SCFAN Bedienungsanleitung

H3C

H3C PSR1600B-12A-B Bedienungsanleitung

H3C

H3C LSQM1TGT24FD0 Bedienungsanleitung

H3C

H3C LSQM1SDNB0 Bedienungsanleitung

H3C

H3C SecPath M9000-AI NSQM5AIASKA1 Bedienungsanleitung

H3C

H3C PSR250-12A Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB04B0 Bedienungsanleitung

H3C

H3C SecPath PSR300-12A2 Bedienungsanleitung

H3C

H3C LSVM1S9800FAN Bedienungsanleitung

H3C

H3C PSR180-56A Bedienungsanleitung

H3C

H3C PSR2400-54D Bedienungsanleitung

H3C

H3C PSR150-A1 Bedienungsanleitung

H3C

H3C PSR750-A Bedienungsanleitung

H3C

H3C PSR2400-12AHAH-B Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung