H3C PSR2400-54A Bedienungsanleitung

H3C PSR2400-54A Power Module

User Manual

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6PW105-20181116

and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of New H3C

Technologies Co., Ltd.

Trademarks

Except for the trademarks of New H3C Technologies Co., Ltd., any

trademarks that may be mentioned in this document are the property

of their respective owners.

Notice

The information in this document is subject to change without notice.

All contents in this document, including statements, information, and

recommendations, are believed to be accurate, but they are

presented without warranty of any kind, express or implied. H3C shall

not be liable for technical or editorial errors or omissions contained

herein.

Environmental protection

This product has been designed to comply with the environmental

protection requirements. The storage, use, and disposal of this

product must meet the applicable national laws and regulations.

Documentation feedback

You can e-mail your comments about product documentation to

[email protected].

We appreciate your comments

Contents

Overview ·················································· 1

Front panel ···································································· 2

LEDs············································································ 2

Technical specifications ··················································· 3

Power module configuration·············································· 4

Installing and removing the power module······· 5

Installing the power module··············································· 5

Installing the power module ·········································· 5

Connecting the power cord··········································· 8

Removing a power module ··············································10

Removing the power cord············································11

Removing the power module········································11

Overview

The PSR2400-54A AC-input and DC-output power module is hot

swappable and provides a maximum output of 2400 W.

Table 1 PSR2400-54A power module features

Feature Description

Protection

Protection against input undervoltage, input

overvoltage, output overvoltage, output short

circuit, output undercurrent, output overcurrent,

and overheat.

Redundancy The power modules can operate in N+1 or N+N

redundancy. For more information, see "Power

module configuration."

Hot swapping You can install or remove a power module

when the device is operating.

The power module shuts down automatically when its temperature

exceeds the acceptable range. When the temperature returns to the

acceptable range, the power module automatically restarts.

Front panel

Figure 1 Front panel

(1) Power input LED (AC OK) (2) Handle

(3) AC input receptacle (4) Latch

(5) Power output LED (DC OK) (6) Air outlet vents

LEDs

The PSR2400-54A power module has two LEDs.

1 2

Table 2 LED description

LED Mark Color Description

Power

input

LED

OK Off

No AC power input.

Low AC input voltage. The power

module has entered

self-protection mode.

Green Normal AC input.

Power

output

LED

Green Normal DC output.

Red

A DC output failure has occurred,

for example, output short circuit,

output overcurrent, output

overvoltage, output undervoltage,

or remote shutdown. The power

module has entered

self-protection mode.

Orange High temperature.

NOTE:

fte

the circuit breaker of the power module is switched off, the

LEDs on the power module will remain on for a while.

Technical specifications

Table 3 Technical specifications

Item Specifications

Rated input voltage 100 to 240 VAC @ 50 or 60 Hz

Rated output voltage 54 VDC

Item Specifications

Maximum input current 16 A

Maximum output current 44.5 A

Maximum output power •1200 W @ 110 VAC

•2400 W @ 220 VAC

Dimensions (H × W × D) 41 × 100 × 332 mm (1.61 × 3.94 ×

13.07 in)

Ambient

temperature

Operating

temperature –10°C to +50°C (–14°F to

+122°F)

Storage

temperature –40°C to + 70°C (–40°F to

+158°F)

Power module configuration

Follow these guidelines to configure power modules for the device:

•Determine the required number of power modules based on the

actual power consumption, the power module slot number, and

power redundancy design.

•Determine the power module redundancy design based on the

power source conditions.

{When two mains power inputs are provided, you can

configure the power modules in N+N redundancy. N+N must

be not greater than the total number of power module slots.

{When one mains power input is provided, you can configure

the power modules in N+1 or N+N redundancy. N+1 or N+N

must be not greater than the total number of power module

slots.

•For easy usage and maintenance, configure a circuit breaker for

each power input. The rated current of the circuit breaker must

be a minimum of 20 A.

Installing and removing the power

module

Installing the power module

To avoid bodily injury and device damage, follow the procedures

in Figure 2 to install a power module.

Figure 2 Power module installation procedure

Before the installation, prepare an ESD wrist strap and a flat-blade

screwdriver yourself.

Installing the power module

1. Wear an ESD wrist strap, and make sure the strap makes good

skin contact and is reliably grounded.

2. Remove the blank panel from the target power module slot.

{If the blank panel is as shown in Figure 3, thread the

flat-blade screwdriver through the hole in the handle of the

blank panel and pull the blank panel out.

{If the blank panel is as shown in Figure 4, put your forefinger

in the hole in the blank panel and pull the blank panel out.

Figure 3 Removing a blank panel (1)

Figure 4 Removing a blank panel (2)

3. Unpack the power module.

4. Correctly orient the power module.

If you install the power module in a left power module slot, make

sure the latch is above the handle. If you install the power

module in a right power module slot, make sure the latch is

below the handle.

5. Holding the handle of the power module with one hand and

supporting the bottom of the power module with the other, slide

the power module along the guide rails into the slot until you

hear a click.

The power module is foolproof. If the power module is oriented

incorrectly, you cannot install the power module into the slot. If

you encounter a hard resistance while inserting the power

module, pull out the power module, reorient it, and then insert it

again.

Inhaltsverzeichnis

Andere H3C Steuereinheit Handbücher

H3C

H3C PSR250-12A1 Bedienungsanleitung

H3C

H3C LSXM1SEERBXD2 Bedienungsanleitung

H3C

H3C PSR450-12A Bedienungsanleitung

H3C

H3C S12500 LST1LB1A1 Bedienungsanleitung

H3C

H3C PSR450-12A Bedienungsanleitung

H3C

H3C SecPath AC2500 Bedienungsanleitung

H3C

H3C S9500E LSR1FW2A1 Bedienungsanleitung

H3C

H3C PSR150-A1 Bedienungsanleitung

H3C

H3C PSR3000-54A Bedienungsanleitung

H3C

H3C PSR750-A Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB04B0 Bedienungsanleitung

H3C

H3C PSR2400-12AHAH-B Bedienungsanleitung

H3C

H3C PSR3000-54A Bedienungsanleitung

H3C

H3C SecPath PSR300-12A2 Bedienungsanleitung

H3C

H3C SecPath DC2400 Bedienungsanleitung

H3C

H3C LSQM1CGS2QSA0 Bedienungsanleitung

H3C

H3C SecPath M9000 NSQM1CGQ20 Bedienungsanleitung

H3C

H3C S9500 LSB1LB1A0 Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB08D0 Bedienungsanleitung

H3C

H3C LSVM2106SFAN Bedienungsanleitung

H3C

H3C Campus SeerEngine LSXM1SEERBXC2 Bedienungsanleitung

H3C

H3C LSQM1TGT24FD0 Bedienungsanleitung

H3C

H3C SecBlade Bedienungsanleitung

H3C

H3C PSR250-12A Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung