H3C PSR650B-12A2-F Bedienungsanleitung

Overview

简介

•The PSR650B-12A2-F

is a DC output power supply that supports AC and

HVDC power input. It provides a maximum output of 650 W.

PSR650B-12A2-F 是一款提供直流输出的电源模块，既支持交流输入也

支持高压直流输入。这款电源模块的最大输出功率可达 650W。

•The PSR650B-12A2-F power supply draws air from its faceplate. The

following figure shows the PSR650B-12A2-F power supply.

PSR650B-12A2-F 的风道风向是电源面板侧进风。下图展示

PSR650B-12A2-F 的外观。

H3C

PSR650B-12A2-F Power Module User

Manual

-APW101

H3C

PSR650B-12A2-F 电源手册-APW101 BOM: 3101A13W

•The PSR650B-12A2-F power supply is applicable to multiple switch

models. The applicable switch models might change over time. For

compatibility of the power supply with switch models, contact the

marketing personnel or technical support. PSR650B-12A2-F 适用于多款

交换机产品，其适用机型的准确信息随着时间变化有更新的可能性，若您

需要详细的适配信息，请咨询市场人员或技术支持人员。

•The restrictions for using the PSR650B-12A2-F

power supply depend on

the switch model. For more information, see the installation guide or

hardware information and specifications for the switch. PSR650B-12A2-F

用于不同交换机产品时可能存在不同的使用限制，具体请参考产品配套安

装指导或硬件描述。

Feature

特点

Description

说明

Self-protection

具有保护功能

Provide output undervoltage, input undervoltage, output overvoltage, short-circuit,

output overcurrent, and overtemperature protections.

具有输出输入欠压保护、输出过压保护、短路保护、输出限流保护、过温保护

等功能

Redundancy

支持冗余备份

Multiple power supplies can be connected in parallel to achieve redundancy

and load sharing.

支持多电源模块并联工作，从而可以实现受电设备电源系统的冗余备份，并且

备份电源间具有负载均流功能

Hot swappable

支持热插拔

You can remove one of power supplies in N+N redundancy while thedevice is

operating. Before removing the power supply, disconnect the power supply

from the external power supply system.

在设备不断电的情况下，可先断开N+N冗余备份电源系统中某个电源模块与外

置供电系统的连接，然后直接对电源模块进行插拔操作

A power supply shuts down after an input undervoltage, short circuit, output

overcurrent, or overtemperature condition occurs. After the issues are

resolved, it automatically restores power supply.

当电源模块触发输入欠压保护、短路保护、输出限流保护、过温保护

功能时，

电源停止供电。当故障消失后，会自动恢复供电。

A power supply shuts down and is locked after an output overvoltage

condition occurs. It cannot restore power supply automatically after the

issue is resolved. To restore power supply, perform the following tasks:

当电源模块触发输出过压保护功能时，电源锁死，停止供电。当电源模块被

锁死时，其不能自动恢复正常工作，可以采用以下步骤来使电源模块恢复正

常工作：

•Disconnect the power cord from the external power supply system.

首先断开电源线与外置电源系统的连接；

•Disconnect the power cord from the power supply and then reconnect it.

接着将电源线插头从电源模块上拔出，然后重新连接电源线至电源模块；

•Connect the power cord to the external power supply system.

最后连接电源线至外置电源系统。

Technical specifications

电源模块规格

Item

项目

Specifications

规格

AC input

交流输入

Rated input voltage range

额定输入电压范围 100 to 240 VAC @ 50/60 Hz

Max input voltage range

最大输入电压范围 90 to 290 VAC @ 47 to 63 Hz

Max input current

最大输入电流 10 A

HVDC input

高压直流输入

Rated input voltage range

额定输入电压范围 240 VDC

Max input voltage range

最大输入电压范围 180 to 320 VDC

Max input current

最大输入电流 4 A

Output voltage 输出电压 12 V

Max output current 最大输出电流 53 A

Max output power 最大输出功率 650 W

Dimensions (H × W × D)

外形尺寸（高×宽×深） 50.5 × 40.2 × 300 mm (1.99 × 1.58 × 11.81 in)

Weight 重量 0.9 kg (1.98 lb)

Operating temperature 工作温度 –10°C to +55°C (14°F to 131°F)

Relative humidity 工作环境相对湿度（非凝露） 5% RH to 95% RH, noncondensing

Storage temperature 存储温度 -40°C to +70°C (–40°F to +158°F)

LEDs

电源模块状态指示灯

The PSR650B-12A2-F power supply provides one LED on its faceplate to indicate

the power input andoutput status. PSR650B-12A2-F 电源模块面板上有 1个电源模

块指示灯，用于指示电源的输入、输出状态。

LED Status

指示灯状态

Description

含义

Steady green

绿色常亮 The power module operates properly, and is in the active state.

电源模块工作正常，处于主用状态

Blinking green

绿色闪烁 The power module operates properly, and is in the standby state.

电源模块工作正常，处于备用状态

Steady red

红色常亮 The power module fails or enters the protected state.

电源模块出现故障或进入保护状态

LED Status

指示灯状态

Description

含义

Red/Green blinking

alternatively

红色/绿色交替闪烁

The power module alarms. The power module encounters

exceptional power output problems, for example, over-voltage

output, under-voltage output, over-current output, over-load, and

over-heat, but does not enter the protected state.

电源模块告警（电源模块出现了如下情况，但还没有进入保护状态：

输出过压、输出欠压、输出过流、输出功率过载、过温等）

Blinking red

红色闪烁

The power module has no power input. The switch has two power

modules. If one has power input, but the other does not, the status

LED of the power module that has no power input blinks red.

当前电源模块没有电流输入（设备安装有两块电源模块，如果其中一

块电源有电流输入、另一块电源无电流输入，此时无电流输入的电源

模块的指示灯会红色闪烁）

Off

灭The power modules have no power input.

电源模块没有电流输入

Installing and removing the power supply

电源模块的安装

和拆卸

1. Safety precautions 安全注意事项

•

Wear an ESD wrist strap and make sure the wrist strap makes good skin

contact.

在安装和拆卸电源模块时请注意佩戴防静电腕带，并确保防静电腕带与皮

肤良好接触。

•

Before installing the power supply, make sure the operating voltage of the

external power supply system

is as required by the power supply, and the

output voltage of the power supply is as required by the powered device.

在安装电源模块前，请确认外置供电系统的工作电压同电源模块所标电

压、电源模块输出电压同受电设备所需电压是否相符，避免对电源模块和

受电设备造成损坏。

•To avoid bodily injury, do not touch any bare wire or terminal.

不要接触露出的任何导线、端子部分，以免对人体造成伤害。

•

To avoid power supply damage, do not open the power supply. When the

internal circuits or components of the power supply fail, contact H3C

Support.

为了防止电源模块受损，请不要随意打开电源模块外壳，当电源模块内部

线路或元器件出现故障时，请移交维修人员进行检修。

•Before installing or r

emoving the power supply, make sure no power cord

is connected to the power supply.

安装和拆卸电源模块时应确保电源模块上没有连接电源线。

2. Tools 工具准备

An ESD wrist strap

is required for installing and removing the power supply

and connecting the power cord. Prepare an ESD wrist strap yourself.

安装和拆卸电源模块和电源线过程中需要使用防静电腕带，请用户自备。

3. Installing the power supply 安装电源模块

•To prevent damage to the power supply or the connector on the

backplane of the powered device, insert the power supply gently.

为了避免损坏电源模块或受电设备背板的连接器端子，在电源模块插入过

程中动作要缓慢。

•If you insert the power supply upside down, you will encounter a hard

resistance because of the special structure designs of the slot and power

supply. You need to pull out thepower supply, orientit correctly, and insert

it again.

如果上下倒置，安装过程将受插槽和电源模块特意设计的结构限制，不能

顺利进行，必须先拔出模块，然后重新插入。

•

Before installing the power supply on a switch, make sure it matches the

switch model. For more information, see the installation guide for the

switch. 安装前请检查电源模块型号与设备是否匹配，具体请参见各产品

的安装指导。

•Keep the filler panel, packaging box, and packaging bags for the power

supply secure for future use. 请妥善保管假面板及电源模块的包装盒、包

装袋等物品，以备将来需要时使用。

(1) Unpack the power supply and verify that the input mode of the power supply is

as required. 从电源模块包装盒中取出电源模块，确认电源模块的输入方式与

所需一致。

(2) Correctly orient the power supply (with the lettering on it upward), grasp the

handle of the power supply with onehand and support its bottom with the other,

and slide the power supply slowly along the guide rails into the slot. Make sure

the latch on thepower supplyclicksinto place. 保证电源模块上下方向正确（请

保证电源模块的锁闩位于拉手下方），用一只手握住电源模块上的拉手，另一

只手托住电源模块底部，将其后端对准电源插槽，使电源模块沿电源插槽水平

插入插槽。当电源模块完全插入插槽时，会听到电源模块上的锁闩卡住插槽的

声音。

If the power supply slot has a filler panel, put your finger into the hole in the

filler panel and then pull the filler panel out of the slot gently. 若准备安装电

源模块的电源槽位上有电源假面板，请先拆卸电源假面板。拆卸方法：将手

指伸入圆孔勾住圆孔边缘，沿插槽导轨向外轻微用力拉出假面板。

4. Connecting the power cord 连接电源线

•Use the power cord provided with the power supply for connection. The

power cord provided with the power supply uses a C13 connector. 请使用

电源模块标配的电源线进行连接，该电源线采用 C13接口。

•Provide a separate circuit breaker for each power cord. 请保证电源线有

独立的输入断路器。

•Before connecting a power cord, make sure the circuit breaker for the

power feed is turned off. 连接电源线前，请将需要连接电源线的输入端断

路器置于断开状态。

(1) Connect the female connector of the power cord to the power input receptacle

on the power supply. 将电源线带插孔的一端插到电源模块的输入插口上。

(2) Use a cable tie to secure the power cord to the handle of the power supply. 用

可拆卸式扎带将电源线固定到电源模块的拉手处，以防电源线脱落。

5. Removing the power supply 拆卸电源模块

•To avoid bodily injury or switch damage, strictly follow the procedure

described in this section to remove the power supply. 请严格按照如下操

作顺序拆卸电源模块，否则可能会造成设备损坏或者人身伤害。

•If you are not to install a new power supply after removing the old one,

install a filler panel in the slot in time. 如果该电源插槽中不再安装电源模

块，请将假面板安装到该插槽上，以免灰尘进入机箱。

(1) Turn off the circuit breaker for the power feed to the power supply. 断开电源输

入端断路器。

(2) Remove the cable tie from the power cord, andthen remove the power cord.松

开固定电源线的可拆卸式扎带，并拔出电源线。

(3) Pressing the latch towards the handle direction, pull the power supply part way

out of the slot. 向拉手侧掰动锁闩，同时沿插槽导轨向外拉动电源模块，将电

源模块拉出来一部分。

(4) Grasping the handle of the power supply with one hand and supporting its

bottom with the other, pull the power supply slowly out of the slot along the

guide rails. 用一只手握住电源模块拉手，另一只手托住电源模块下方，将电源

模块沿着插槽导轨水平缓慢地拉出。

(5) Put the removed power supply into an antistatic bag. 将拆卸下来的电源模块放

到防静电袋中。

Ltd.

The information in this document is subject to change without notice.

本文档中的信息如有更改，恕不另行通知

如需了解产品及安装方面的更多信息，请登录 H3C网站 www.h3c.com

Inhaltsverzeichnis

Andere H3C Steuereinheit Handbücher

H3C

H3C PSR2400-54D Bedienungsanleitung

H3C

H3C SecPath AC2500 Bedienungsanleitung

H3C

H3C NSQM1FWDFGC1 Bedienungsanleitung

H3C

H3C SecPath M9000-AI NSQM5AIASKA1 Bedienungsanleitung

H3C

H3C LSQM1TGT24FD0 Bedienungsanleitung

H3C

H3C LSXM1SEERBXD2 Bedienungsanleitung

H3C

H3C LSQM1CGS2QSA0 Bedienungsanleitung

H3C

H3C LSVM1S9810FAN Bedienungsanleitung

H3C

H3C SIC-4G-LTE-M Bedienungs- und Wartungsanleitung

H3C

H3C SIC-4G-CAT6 Bedienungsanleitung

H3C

H3C PSR450-12A Bedienungsanleitung

H3C

H3C LSWM18CQ Bedienungsanleitung

H3C

H3C SecPath DC2400 Bedienungsanleitung

H3C

H3C PSR250-12A Bedienungsanleitung

H3C

H3C SecPath M9000 NSQM1MBFEA0 Bedienungsanleitung

H3C

H3C PSR3000-54A Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM-200 Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB04B0 Bedienungsanleitung

H3C

H3C LSVM152SCFAN Bedienungsanleitung

H3C

H3C PSR2400-12AHAH-B Bedienungsanleitung

H3C

H3C SecPath PSR300-12A2 Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB08D0 Bedienungsanleitung

H3C

H3C SecPath NSQM2GP24TSSC0 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung