Hama EWS-810 Bedienungsanleitung

123127

EWS-810

Weather Station

Wetterstation

RUS

Operating Instructions

Bedienungsanleitung

Mode d‘emploi

Instrucciones de uso

Руководство по эксплуатации

Istruzioni per l‘uso

Οδηγίες χρήσης

Instrukcja obsługi

Návod na použitie

Manual de instruções

CONTRAST

MODE ALARM

S N O O Z E / LI G H T

321

11 6

15 16 17 18 19

21 24

2523

GOperating instruction

Controls and Displays

A Base station

1. Day

2. Month

3. Weekday

4. Alarm symbol

5. Summer time

6. Battery symbol (base station)

7. Room temperature

8. Outdoor temperature

9. Channel display

10. Channel overview

11. Battery symbol (measuring station)

12. Time

13. Wireless symbol

14. SNOOZE/LIGHT button = Stops the alarm/Activates the backlight (approx. 5 seconds)

15. MODE button = Settings/Conrms the setting/Switches display mode

16. ALARM button = Deactivates/Activates the alarm functions

17. +button = Increases the current setting/Selects channel if there are multiple external

temperature sensors/Manual search for a signal from the measuring station

18. –button = Decreases the current setting/Toggles between °C and °F/Activates/

deactivates manual radio signal reception

19. CONTRAST button = Controls the backlight

20. Battery compartment

B Measuring station

21. Transmission indicator lamp

22. Display

23. CH button = Selects the channel

24. Opening for wall mounting

25. °C/°F button = Switches between °C and °F

26. Battery compartment

Thank you for choosing a Hama product.

Take your time and read the following instructions and information completely. Please keep

these instructions in a safe place for future reference. If you sell the device, please pass these

operating instructions on to the new owner.

1. Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your attention to specic

hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

2. Package Contents

•Weather station EWS-810

(base station for indoor/outdoor measuring station)

•4 AAA batteries

•These operating instructions

3. Safety Instructions

•The product is intended for private, non-commercial use only.

•Do not operate the product outside the power limits given in the specications.

•Do not use the product in moist environments and avoid splashes.

•Do not use the product in the immediate vicinity of heaters or other heat sources or in

direct sunlight.

•Do not use the product in areas where the use of electronic devices is not permitted.

•Do not place the product near interference elds, metal frames, computers, TVs, etc.

Electronic devices and window frames can negatively affect the product’s functionality.

•Do not drop the product and do not expose it to any major shocks.

•Do not open the device or continue to operate it if it becomes damaged.

•Do not attempt to service or repair the product yourself. Leave any and all service work to

qualied experts.

•Keep the packaging material out of the reach of children due to the risk of suffocation.

•Dispose of packaging material immediately according to locally applicable regulations.

•Do not modify the product in any way. Doing so voids the warranty.

Warning – Batteries

•Immediately remove and dispose of dead batteries from the product.

•Only use batteries (or rechargeable batteries) that match the specied type.

•Do not mix old and new batteries or batteries of a different type or make.

•When inserting batteries, note the correct polarity (+ and - markings) and insert the

batteries accordingly. Failure to do so could result in the batteries leaking or exploding.

•Do not charge batteries.

•Keep batteries out of the reach of children.

•Do not short circuit the batteries/rechargeable batteries and keep them away from

uncoated metal objects.

4. Getting Started

4.1. Measuring station

•Open the battery compartment (26) and insert two AAA batteries with the correct polarity.

•Press the CH button (23) repeatedly to select the channel the measuring station is to use

for transmission. CH1, CH2 or CH3 is shown on the display.

•Press the °C/°F button (25) to choose between °C and °F for the temperature display.

•Close the battery compartment.

Note

Before use, ensure you insert the batteries in the measuring station rst and then in the

base station.

4.2. Base station

•Open the battery compartment (20) and insert two AAA batteries with the correct polarity.

Close the battery compartment.

5. Installation

Note – Installation

•We recommend initially placing the base and measuring stations in the intended

locations without installing them and making all the settings described in 6. Operation

– to do.

•Only install the stations once the appropriate settings have been made and a stable

wireless connection is established.

Note

•The wireless transmission range between the measuring and base stations is up to 30

m in open spaces.

•Before installation, ensure that wireless transmission will not be disrupted by

interference or obstacles like buildings, trees, vehicles, high-voltage lines, etc.

•Before the nal installation, ensure that there is sucient reception between the

intended installation locations.

•When installing the measuring station, ensure that it is protected from direct sunlight

and rain.

•The international standard height for measuring air temperature is 1.25 m (4 ft) above

ground.

Warning

•Buy special or suitable installation material from a specialised dealer for wall-mounting.

•Ensure that no faulty or damaged parts are installed.

•Never apply force during installation. This could damage the product.

•Before installation, ensure that the chosen wall is suitable for the weight to be

mounted, and make sure that there are no electrical wires, water, gas or other lines at

the installation site on the wall.

5.1. Base station

•Use the base to position the base station on a level surface.

5.2. Measuring station

•You can also position the measuring station on a level outdoor surface.

•We recommend installing the measuring station securely on an outdoor wall using the

opening (24).

•Install an anchor, screw, nail, etc. in the wall of your choice.

•Hang up the base/measuring station using the opening intended for this purpose.

6. Operation

Note – Input

Hold down the +button (17) or the –button (18) to select the values faster.

6.1. Connection to the measuring station

•After you insert the batteries, the base station automatically searches for a connection to

the measuring station and performs initial setup.

Note

•Initial setup takes approx. 3 minutes.

•Do not press any buttons during setup. Otherwise, values may not be transmitted

correctly and there is a risk of value errors and inaccuracies.

•The setup process is completed when the indoor (7) and outdoor (8) measurement data

is displayed.

•If the base station still does not receive a signal from the measuring station, press and hold

the +button (17) for approx. 3 seconds to start the manual search for the signal.

6.2. Selecting the channel/Other measuring stations

Note

You can install two more measuring stations in addition to the included measuring station.

Ensure that the base and measuring stations are set to the same channel.

Visit www.hama.com for suitable measuring stations.

•Press the +button (17) repeatedly to set the channel to that set on the respective

measuring station – see 4.1. Measuring station .CH1, CH2, CH3 (9) or Channel

overview (10) is displayed.

•The base station now shows the temperature measured (8) on the selected measuring

station (9).

•Select Channel overview (10) to show the measurement values of the individual measuring

stations/channels consecutively for 5 seconds each.

6.3. Basic and manual settings

Automatic setting using the DCF signal

•After the rst time the base station is switched on and successful transmission is established

between the base station and the measuring station, the clock will automatically search for

a DCF signal. During the search, the wireless symbol (13) will ash.

Display Searching for the DCF signal

Flashing

Active

Displayed continuously

Successful – signal is being received

No display Deactivated

•If the station still does not receive a signal, press and hold the –button (18) for approx. 3

seconds to start the manual search for the DCF signal. The wireless symbol (13) will start

to ash.

Note – Time settings

•The search process takes about 7 minutes. If the search fails, it ends and is repeated at

the next clock hour. The wireless symbol (13) will go out.

•In the meantime you can, however, set the time and the date manually.

•The clock automatically continues to search for the DCF signal on a daily basis (between

1:00 a.m. and 3:00 a.m.). If the signal is received successfully, the manually-set time

and date are overwritten.

Note – Summer time

•The clock automatically switches to summer time. DST (5) appears on the display as

long as summer time is activated.

•Press and hold the –button (18) again for approx. 3 seconds to stop the manual search.

(Manual) settings

•Press and hold the –button (18) for approx. 3 seconds to stop the search for the DCF

signal. The wireless symbol (13) goes out and you can set the time manually.

•Press and hold the MODE button (15) for approx. 3 seconds to make the following settings

one after the other:

•12/24 hour format (12)

•Time zone (12)

•Hours (12)

•Minutes (12)

•Weekday (3)

•Year (12)

•Month (2)

•Day (1)

•To select the individual values, press the +button (17) or the –button (18) and conrm

each selection by pressing the MODE button (15).

•If you do not make an entry for 13 seconds, you automatically exit setup mode.

Note – Time zone

•The DCF signal can be received over long distances, but always transmits the current

Central European Time in Germany. Make sure you account for the time difference in

countries with another time zone.

•If you are in Moscow, the time is 3 hours later than in Germany. This means that you

should set +3 for the time zone. The clock then automatically sets the time to 3 hours

after the DCF signal received or relative to the manually set time.

Note – Weekday

You can choose from German (GE), English (EN), Danish (DA), Dutch (NE), Italian (IT),

Spanish (ES) and French (FR) for the weekday display.

Celsius/Fahrenheit

•Press the –button (18) to switch between °C and °F for the temperature display.

Alarm

•Repeatedly press the MODE button (15) to access alarm mode 1 or 2 .

A1 or A2 is displayed accordingly in the seconds display.

•Press and hold the MODE button (15) for approx. 3 seconds to set the signal time of the

alarm displayed. The hours display begins to ash.

•Press the +button (17) or the –button (18) to select the hour for the alarm time and

conrm your selection by pressing the MODE button (15). The minutes display begins to

ash.

•Repeat the process to set the minutes for the alarm time.

•Press the MODE button (15) repeatedly to also set the other alarm mode or return to the

time display (12).

•If you do not make an entry for 13 seconds, you automatically exit the setting mode.

•Press the ALARM button (16) to activate/deactivate Alarm 1, Alarm 2 or both. The alarm

symbol (4) will appear/not appear.

•If the alarm is triggered, the alarm symbol (4) will begin to ash and an alarm will sound.

•Press any button (except the SNOOZE/LIGHT button (14)) to stop the alarm. Otherwise, it

will stop automatically after 2 minutes.

•If you press the SNOOZE/LIGHT button (14) during the alarm, the alarm is interrupted for

5 minutes and then goes off again. The alarm symbol (4) will ash.

6.4. Backlight

Note – Backlight

•If you press the SNOOZE/LIGHT button (14), the display will light up for approx. 5

seconds.

Inhaltsverzeichnis

Sprachen:

Andere Hama Wetterstation Handbücher

Hama

Hama Magic Color Bedienungsanleitung

Hama

Hama EWS-152 Bedienungsanleitung

Hama

Hama TH500 Bedienungsanleitung

Hama

Hama EWSC-100 Bedienungsanleitung

Hama

Hama 00092659 EWS-165 Bedienungsanleitung

Hama

Hama Milano Bedienungsanleitung

Hama

Hama EWS-2020 Bedienungsanleitung

Hama

Hama EWS-150 Bedienungsanleitung

Hama

Hama Black Line Bedienungsanleitung

Hama

Hama EWS 1500 Bedienungsanleitung

Hama

Hama 99123148 WS-710 Bedienungsanleitung

Hama

Hama TH-100 Bedienungsanleitung

Hama

Hama EWS-880 Bedienungsanleitung

Hama

Hama EWS-170 Bedienungsanleitung

Hama

Hama 186421 Bedienungsanleitung

Hama

Hama i@Sky Bedienungsanleitung

Hama

Hama EWS-151 Bedienungsanleitung

Hama

Hama EWS-860 Bedienungsanleitung

Hama

Hama WFC840 Bedienungsanleitung

Hama

Hama WDS-300 Bedienungsanleitung

Hama

Hama EWS-830 Bedienungsanleitung

Hama

Hama EWS-850 Bedienungsanleitung

Hama

Hama WFC-960 Bedienungsanleitung

Hama

Hama 00075297 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86371 Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung