Harbor Breeze SHREVEPORT E-NO52AB5C4 Bedienungsanleitung

ITEM #0294986

0294985

E192641

SHREVEPORT CEILING FAN

MODEL #E-NO52AB5C4

E-NO52PAN5C4

Questions, problems, missing parts? Before returning to your retailer, call or contact our

customer service department at 1-800-527-1292, 8:30 a.m. - 5:00 p.m., CST, Monday - Friday.

Harbor Breeze® is a registered trademark of

Español p. 19

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

Federal regulations require ceiling fans with light kits manufactured or imported after

January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,

this fan is equipped with a wattage limiting device. If you lamp this fan's light kit with

bulbs totaling more than 190W, the wattage limiting device will reduce the watts

consumed to 190W.

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate the

product. If you have any questions regarding the product, please call customer service at

1-800-527-1292, 8:30 a.m.- 5:00 p.m., CST, Monday - Friday.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for

repairs, it must be shipped in its original packaging to ensure proper protection against damage that

might exceed the initial cause for return.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook,

available at Lowe's, if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 feet from the blades to

the floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure that all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 20.94 lbs. (9.5 kg).

TABLE OF CONTENTS

Safety Information ....…………………………………………………………………………...…….2 - 3

Package Contents ........…………………………………………………………………..……..…..…..4

Hardware Contants ........................................................................................................................5

Preparation .........….…………………..……………………….…………….………………....5

Initial Installation ...............……………………...………………………………….............6 - 7

Downrod Style Fan Mounting ...…………………………....……………....……..........................7 - 8

Closemount Style Fan Mounting ……………………...............…....……………………......8 - 9

Wiring ..............................................................................………………………................9 - 11

Final Installation ………….…………….……………………….………….....….....................11 - 14

Operation Instructions..............................................................………………………………...14 - 15

Care and Maintenance ....……………………………………………………………….......................15

Troubleshooting .....................………...………………………….……………..………...........16 - 17

Warranty ………………………………….…………………………………………..……..............17

Replacement Parts List ...............................................................................................................18

CAUTIONS

Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

Read all instructions and safety information before installing your new fan. Review the

accompanying assembly diagrams.

SAFETY INFORMATION

To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box

marked "ACCEPTABLE FOR FAN SUPPORT" and use mounting screws provided with

the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are

not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in

doubt. Secure the outlet box directly to the building structure. The outlet box and its support must

be able to support the moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.

To avoid personal injury, the use of gloves may be necessary while handling fan parts with

sharp edges.

To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this

fan are designed to accept only one 12 gauge house wire and two lead wires from the fan. If your

house wire is larger than 12 gauge or there is more than one house wire to connect to the two fan

lead wires, consult an electrician for the proper size wire connectors to use.

To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed

control device or control fan speed with a full range dimmer switch.

To reduce the risk of fire, electrical shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert objects between the

rotating fan blades.

To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

WARNINGS

IMPORTANT REMINDER: You must

use the parts provided with this fan for

proper installation and safety.

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

Downrod

Canopy 1

Mounting Bracket

Motor Housing

E Switch Housing

F Light Kit Fitter

Blade

Blade Arm

I Glass Shade 4

PART DESCRIPTION QUANTITY

J Motor Screw (preassembled)

K 6 mm Lock Washer 15

(preassembled)

L Canopy Mounting Screw 4

(preassembled)

M Pin (preassembled)

Clip (preassembled)

Pull Chain Extension

Candelabra Base Bulb 4

HARDWARE CONTENTS (shown actual size)

Fiber

Blade

Washer

Qty. 15

BB CC

Blade

Screw

Qty. 15 E3 Wire

Connector

Qty. 4

Before beginning assembly and installation of product, make sure all parts are present. Compare

parts with package contents list and hardware contents above. If any part is missing or

damaged, do not attempt to assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety

Glasses, Stepladder and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself-Wiring Handbook

(available at Lowe’s) and Wire Cutters

Bulbs Required (included): 4 candelabra base 40-watt max. bulbs

DANGER: When using an existing outlet box, make sure the outlet box is securely attached to

the building structure and can support the full weight of the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan

after installation is complete.

CAUTION: Be sure outlet box is properly grounded and that a ground wire (green or bare) is

present.

After opening top of carton, remove mounting hardware package from foam inserts. Remove motor

from packing and place on carpet or on foam to avoid damage to ﬁnish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that they

are secured.

PREPARATION

Thumb

Screw

Qty. 12

Hex

Nut

Qty. 1

Lock

Washer

Qty. 1

EE FF

INITIAL INSTALLATION

OFF

Turn off circuit breakers and wall switch to the fan

supply line leads. (Fig. 1)

DANGER: Failure to disconnect power supply

prior to installation may result in serious injury or

death.

Determine mounting method to use. (Fig. 2)

A. Downrod mount (normal or angled ceiling)

B. Closemount (normal ceiling only)

Important: If using the angle mount, check to

make sure the ceiling angle is not steeper than 19°.

2. 2

Check to make sure blades (G) are at least 30 in.

from any obstruction. Check downrod (A) length to

ensure blades (G) are at least 7 ft. above the floor.

(Fig. 3)

Secure mounting bracket (C) to outlet box using

screws, spring washers, and flat washers

provided with the outlet box. (Fig. 4)

*NOTE: It is very important that you use the

proper hardware when installing the mounting

bracket (C) as this will support the fan.

IMPORTANT: If using the angle mount, make

sure open end of mounting bracket (C) is installed

facing the higher point of the ceiling.

7 ft.

min.

30 in.

min.

INITIAL INSTALLATION

5. Remove motor screws (J) and 6 mm lock

washers (K) from underside of motor and save for

blade arm (H) attachment later on. [If there are

plastic motor blocks installed with the motor

screws (J) and 6 mm lock washers (K), discard

the plastic motor blocks.] (Fig. 5)

Follow mounting instructions on pages 7 and 8 for

“Downrod Style Fan Mounting” or proceed to

pages 8 and 9 for “Closemount Style Fan

Mounting”, depending on mounting method (A or

B) chosen in Step 2 on previous page.

Remove pin (M) and clip (N) from motor housing

yoke at top of motor housing (D) and partially loosen

set screws. (Fig. 1)

*Helpful Hint: Downrod style mounting is best

suited for ceilings 8 ft. (2.44 m) high or higher. For

taller ceilings you may want to use a longer downrod

(sold separately) than the one provided. Angle style

mounting is best suited for angled or vaulted

ceilings. A longer downrod is sometimes necessary

to ensure proper blade clearance.

Set

Screw

DOWNROD STYLE FAN MOUNTING

Insert downrod (A) through canopy (B). Thread

wires from motor housing (D) through downrod

(A). (Fig. 2)

2. 2

Slip downrod (A) into motor housing yoke, align

holes and re-install pin (M) and clip (N).

Re-tighten set screws in motor housing yoke

and then tighten nuts. (Fig. 3)

Set

Screw

Continue to "Wiring" instructions on page 9.

Install ball end of downrod (A) into mounting

bracket (C) opening. Align slot in ball with tab in

mounting bracket (C). (Fig. 6)

DANGER: Failure to align slot in ball with tab

may result in serious injury or death.

Depending on the length of downrod (A) you use, you

may need to cut the lead wires back to simplify the

wiring. If you decide to cut back the lead wires, it is

suggested that you do so in the following manner:

Take the lead wires and make sure that you have

pulled them all the way through the top of the downrod

(A). Start at the TOP of the ball on the downrod (A) and

measure 8 in. of lead wire, and then cut the excess

wire off with wire cutters. (Fig. 4)

Note: If you do not cut back the lead wires, Steps 4

and 5 are not necessary and you may proceed to

Step 6 instead.

If you decided to cut back the lead wires in Step 4,

strip 1/2 in. of insulation from end of white wire. Twist

stripped ends of each strand of wire within the

insulation with pliers. (Fig. 5) Repeat Step 5 for

black, blue (if applicable) and green wires.

DOWNROD STYLE FAN MOUNTING

BHanging

Ball Slot

Tab

Ball

Remove canopy cover from bottom of canopy (B).

(Fig. 1) [Note: It may be necessary to use the handle

end of a screwdriver to remove the canopy cover by

tapping on the canopy cover from the inside of the

canopy (B).]

*Helpful Hint: Closemount style mounting is more

suitable for ceilings lower than 8 ft. (2.44 m) high.

The downrod, hanging ball, and canopy cover are

not used in this type of installation.

Canopy

Cover

CLOSEMOUNT STYLE FAN MOUNTING

If neccessary, remove every other screw and lock

washer from top of motor housing (D). (If there are

only three screws and lock washers in top of motor

housing (D), the other three screws and lock

washers will be located in one of the hardware

packs.) (Fig. 2)

Remove pin (M), clip (N) and set screws from motor

housing yoke. (Fig. 2)

Pull wires through hole in canopy (B) and attach

canopy (B) to motor housing (D) using the three

screws and three lock washers mentioned in the

first paragraph of the previous step. (Fig. 3)

Set Screw

CLOSEMOUNT STYLE FAN MOUNTING

Hang motor housing (D) on the tab on the mounting

bracket (C) using one of the non-slotted holes in

the canopy (B). (Fig. 4)

Tab

WIRING

WARNING: To reduce the risk of fire, electrical

shock, or personal injury, wire connectors provided

with this fan are designed to accept only one 12

gauge house wire and two lead wires from the fan. If

your house wire is larger than 12 gauge or there is

more than one house wire to connect to the two fan

lead wires, consult an electrician for the proper size

wire connectors to use.

CAUTION: Be sure outlet box is properly grounded

and that a ground (green or bare) wire is present.

WARNING: If house wires are different colors than

referred to in the following steps, stop immediately. A

professional electrician is recommended to determine

wiring. 9

WIRING

Choose wiring diagram (Fig. 1A, Fig. 1B or Fig. 1C)

that fits your situation and make appropriate wiring

connections as follows: [NOTE: For each wire

connection below, use one of the wire connectors

(CC) provided, making sure to screw wire connector

(CC) on in a clockwise direction.]

1A. FAN AND LIGHT CONTROLLED BY PULL

CHAINS: Connect BLACK and BLUE wire from fan

to BLACK wire from ceiling. Connect WHITE wire

from fan to WHITE wire from ceiling. Connect all

GROUND (GREEN) wires together from fan (on

downrod and mounting bracket) to BARE/GREEN

wire from ceiling. (Fig. 1A)

1B. FAN CONTROLLED BY PULL CHAIN, LIGHT

BY WALL SWITCH: If you intend to control the fan

light with a separate wall switch, connect BLACK

wire from fan to BLACK wire from ceiling. Connect

BLUE wire from fan to the BLACK wire from the

independent wall switch for the light. Connect

WHITE wire from fan to WHITE wire from ceiling.

Connect all GROUND (GREEN) wires together

from fan (on downrod and mounting bracket) to

BARE/GREEN wire from ceiling. (Fig. 1B)

1C. FAN AND LIGHT CONTROLLED BY TWO

WALL SWITCHES: If you intend to control the fan

and light with separate wall switches, connect

BLACK wire from fan to BLACK wire from the

independent wall switch for the fan. Connect BLUE

wire from fan to the BLACK wire from the other

independent wall switch for the light. Connect

WHITE wire from fan to WHITE wire from ceiling.

Connect all GROUND (GREEN) wires together

from fan (on downrod and mounting bracket) to

BARE/GREEN wire from ceiling. (Fig. 1C)

Note: Black wire is hot power for fan. Blue wire is hot

power for light kit. White wire is common for fan and

light kit. Green or bare wire is ground.

FAN AND LIGHT CONTROLLED BY PULL CHAINS

BLACK

WHITE

GROUND/GREEN (BARE)

WHITE

BLUE

WHITE

FROM FAN

120 V Power

FROM

CEILING

FAN CONTROLLED BY PULL CHAIN, LIGHT BY

WALL SWITCH

WHITE

BLACK

BLACK (WALL SWITCH)

GROUND/GREEN (BARE)

BLACK

BLUE

WHITE

FROM FAN

FAN

120 V Power

FROM

CEILING

WHITE

BLACK (WALL SWITCH)

BLACK (WALL SWITCH FOR LIGHT)

GROUND/GREEN (BARE)

BLACK

BLUE

WHITE

FROM FAN

FAN

120 V Power

FROM

CEILING

FAN AND LIGHT CONTROLLED BY TWO WALL

SWITCHES

FAN

GREEN

BLACK

GREEN

WHITE

GREEN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Harbor Breeze Lüfter Handbücher

Harbor Breeze

Harbor Breeze E-TM52BNK5LED Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40945 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40680 Bedienungsanleitung

Harbor Breeze

Harbor Breeze TALAMORE TAL60MBK8LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze AR09-52WHT Bedienungsanleitung

Harbor Breeze

Harbor Breeze COGDELL COG60BNK7LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze GAT24MBK6LOD Bedienungsanleitung

Harbor Breeze

Harbor Breeze ECHOLAKE 42080 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 317058 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40410 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 52 IN CLASSIC STYLE 40081 Bedienungsanleitung

Harbor Breeze

Harbor Breeze MERRIMACK II 41125 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BDB52ABZC5P Bedienungsanleitung

Harbor Breeze

Harbor Breeze FREEPORT LP8079LAZ Bedienungsanleitung

Harbor Breeze

Harbor Breeze 0184428 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 00881 Bedienungsanleitung

Harbor Breeze

Harbor Breeze Casual-3-2011 Bedienungsanleitung

Harbor Breeze

Harbor Breeze STONECROFT 41946 Bedienungsanleitung

Harbor Breeze

Harbor Breeze LP8115LAZ Bedienungsanleitung

Harbor Breeze

Harbor Breeze RLC52WW5C1R Bedienungsanleitung

Harbor Breeze

Harbor Breeze 80209 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BRADBURY BRD48BNK6LRS Bedienungsanleitung

Harbor Breeze

Harbor Breeze WELLSBORO 42072 Handbuch

Harbor Breeze

Harbor Breeze MAZON MZ44MBK3LR Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung